| Age | Commit message (Collapse) | Author |
|---|
|
This is a duplicate of dev->fmt and can be removed. As a consequence a
lot of tests that check if the format has changed midstream can be
removed as well: the format cannot change midstream, so this is a bogus
check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
switches port3
The only remaining place that modifies the relevant bit is in function
cx231xx_set_Colibri_For_LowIF
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The scanning itself just fails (as before this series) but now
the correct busses are scanned.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
All switching should be done by i2c mux adapters.
Drop explicit dont_use_port_3 flag.
Drop info message about switch.
Only the removed code in start_streaming is questionable:
It did switch the port_3 flag without accessing i2c in between.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
I2C bus 1 has internally a switch. Use it as I2C_1_MUX_1 and
I2C_1_MUX_3, letting the I2C core handling the switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
change almost all instances of I2C_1 to I2C_1_MUX_3
Only these cases are changed to I2C_1_MUX_1:
* All that have dont_use_port_3 set.
* CX231XX_BOARD_HAUPPAUGE_EXETER, old code did explicitly not switch to port3.
* eeprom access for 930C
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
number
Get used i2c port from bus_nr and status of port_3 switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is used later for is_tuner function that switches i2c behaviour for
some tuners.
[mchehab@osg.samsung.com: Fix CodingStyle on a multi-line comment]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is a preparation for mapping I2C_1_MUX_1 and I2C_1_MUX_3 later to the seperate
muxed i2c adapters.
Map mux adapters to I2C_1 for now.
Add local variables for i2c_adapters in dvb_init to get line lengths
shorter.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Replace numbers by the constants of same value and same meaning.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Change to I2C_0 ... I2C_2 for the master ports
and add I2C_1_MUX_1 and I2C_1_MUX_3 for the muxed ones.
V2: Renamed mux adapters to seperate them from master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Instead of using the same name for all 3 i2c physical buses
inside cx231xx, name them differently, adding a number
to it. This helps to better deal with the logs.
[mchehab@osg.samsung.com: removed an unused bus_name var from
the original patch]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
For each i2c master there is a i2c_client allocated that could be
deleted now that its only two users have been changed to use their
own i2c_client.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
lockdep reports a potential circular dependecy deadlock when registering input device.
Unlock mutex rc_dev->lock prior to calling ir_raw_event_register to avoid the circular
dependency since that function also calls input_register_device and rc_open.
======================================================
[ INFO: possible circular locking dependency detected ]
3.17.0-rc7+ #24 Not tainted
-------------------------------------------------------
modprobe/647 is trying to acquire lock:
(input_mutex){+.+.+.}, at: [<ffffffff812ed81c>] input_register_device+0x2ba/0x381
but task is already holding lock:
(ir_raw_handler_lock){+.+.+.}, at: [<ffffffff813186ed>] ir_raw_event_register+0x102/0x190
which lock already depends on the new lock.
[cut text]
other info that might help us debug this:
Chain exists of:
input_mutex --> &dev->lock --> ir_raw_handler_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(ir_raw_handler_lock);
lock(&dev->lock);
lock(ir_raw_handler_lock);
lock(input_mutex);
*** DEADLOCK ***
4 locks held by modprobe/647:
#0: (&dev->mutex){......}, at: [<ffffffff812d19f3>] device_lock+0xf/0x11
#1: (&dev->mutex){......}, at: [<ffffffff812d19f3>] device_lock+0xf/0x11
#2: (&dev->lock){+.+.+.}, at: [<ffffffff81317fff>] rc_register_device+0x55d/0x58a
#3: (ir_raw_handler_lock){+.+.+.}, at: [<ffffffff813186ed>] ir_raw_event_register+0x102/0x190
stack backtrace:
CPU: 0 PID: 647 Comm: modprobe Not tainted 3.17.0-rc7+ #24
Call Trace:
[<ffffffff81489d6a>] dump_stack+0x46/0x58
[<ffffffff81487699>] print_circular_bug+0x1f8/0x209
[<ffffffff81074353>] __lock_acquire+0xb54/0xeda
[<ffffffff81080f17>] ? console_unlock+0x34d/0x399
[<ffffffff81074c01>] lock_acquire+0xd9/0x111
[<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381
[<ffffffff8148e650>] mutex_lock_interruptible_nested+0x57/0x381
[<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381
[<ffffffff81124e03>] ? kfree+0x7c/0x96
[<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381
[<ffffffff81072531>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff812ed81c>] input_register_device+0x2ba/0x381
[<ffffffff8131a537>] ir_mce_kbd_register+0x109/0x139
[<ffffffff81318728>] ir_raw_event_register+0x13d/0x190
[<ffffffff81317e40>] rc_register_device+0x39e/0x58a
[<ffffffff81072531>] ? trace_hardirqs_on+0xd/0xf
[<ffffffffa00cf2e3>] nvt_probe+0x5ad/0xd52 [nuvoton_cir]
[<ffffffffa00ced36>] ? nvt_resume+0x80/0x80 [nuvoton_cir]
[<ffffffff81296003>] pnp_device_probe+0x8c/0xa9
[<ffffffff812d1b94>] ? driver_sysfs_add+0x6e/0x93
[<ffffffff812d203a>] driver_probe_device+0xa1/0x1e3
[<ffffffff812d217c>] ? driver_probe_device+0x1e3/0x1e3
[<ffffffff812d21ca>] __driver_attach+0x4e/0x6f
[<ffffffff812d075b>] bus_for_each_dev+0x5a/0x8c
[<ffffffff812d1b24>] driver_attach+0x19/0x1b
[<ffffffff812d1879>] bus_add_driver+0xf1/0x1d6
[<ffffffff812d2817>] driver_register+0x87/0xbe
[<ffffffffa0120000>] ? 0xffffffffa0120000
[<ffffffff81295da4>] pnp_register_driver+0x1c/0x1e
[<ffffffffa0120010>] nvt_init+0x10/0x1000 [nuvoton_cir]
[<ffffffff8100030e>] do_one_initcall+0xea/0x18c
[<ffffffff8111497f>] ? __vunmap+0x9d/0xc7
[<ffffffff810a3ca1>] load_module+0x1c21/0x1f2c
[<ffffffff810a0bce>] ? show_initstate+0x44/0x44
[<ffffffff810a404e>] SyS_init_module+0xa2/0xb1
[<ffffffff81490ed2>] system_call_fastpath+0x16/0x1b
Signed-off-by: Tomas Melin <tomas.melin@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patches fixes an ancient bug in the dvb_usb_af9005 driver, which
has been reported at least in the following threads:
https://lkml.org/lkml/2009/2/4/350
https://lkml.org/lkml/2014/9/18/558
If the driver is compiled in without any IR support (neither
DVB_USB_AF9005_REMOTE nor custom symbols), the symbol_request calls in
af9005_usb_module_init() return pointers != NULL although the IR
symbols are not available.
This leads to the following oops:
...
[ 8.529751] usbcore: registered new interface driver dvb_usb_af9005
[ 8.531584] BUG: unable to handle kernel paging request at 02e00000
[ 8.533385] IP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d
[ 8.535613] *pde = 00000000
[ 8.536416] Oops: 0000 [#1] PREEMPT PREEMPT DEBUG_PAGEALLOCDEBUG_PAGEALLOC
[ 8.537863] CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc6-00151-ga5c075c #1
[ 8.539827] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 8.541519] task: 89c9a670 ti: 89c9c000 task.ti: 89c9c000
[ 8.541519] EIP: 0060:[<7d9d67c6>] EFLAGS: 00010206 CPU: 0
[ 8.541519] EIP is at af9005_usb_module_init+0x6b/0x9d
[ 8.541519] EAX: 02e00000 EBX: 00000000 ECX: 00000006 EDX: 00000000
[ 8.541519] ESI: 00000000 EDI: 7da33ec8 EBP: 89c9df30 ESP: 89c9df2c
[ 8.541519] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[ 8.541519] CR0: 8005003b CR2: 02e00000 CR3: 05a54000 CR4: 00000690
[ 8.541519] Stack:
[ 8.541519] 7d9d675b 89c9df90 7d992a49 7d7d5914 89c9df4c 7be3a800 7d08c58c 8a4c3968
[ 8.541519] 89c9df80 7be3a966 00000192 00000006 00000006 7d7d3ff4 8a4c397a 00000200
[ 8.541519] 7d6b1280 8a4c3979 00000006 000009a6 7da32db8 b13eec81 00000006 000009a6
[ 8.541519] Call Trace:
[ 8.541519] [<7d9d675b>] ? ttusb2_driver_init+0x16/0x16
[ 8.541519] [<7d992a49>] do_one_initcall+0x77/0x106
[ 8.541519] [<7be3a800>] ? parameqn+0x2/0x35
[ 8.541519] [<7be3a966>] ? parse_args+0x113/0x25c
[ 8.541519] [<7d992bc2>] kernel_init_freeable+0xea/0x167
[ 8.541519] [<7cf01070>] kernel_init+0x8/0xb8
[ 8.541519] [<7cf27ec0>] ret_from_kernel_thread+0x20/0x30
[ 8.541519] [<7cf01068>] ? rest_init+0x10c/0x10c
[ 8.541519] Code: 08 c2 c7 05 44 ed f9 7d 00 00 e0 02 c7 05 40 ed f9 7d 00 00 e0 02 c7 05 3c ed f9 7d 00 00 e0 02 75 1f b8 00 00 e0 02 85 c0 74 16 <a1> 00 00 e0 02 c7 05 54 84 8e 7d 00 00 e0 02 a3 58 84 8e 7d eb
[ 8.541519] EIP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d SS:ESP 0068:89c9df2c
[ 8.541519] CR2: 0000000002e00000
[ 8.541519] ---[ end trace 768b6faf51370fc7 ]---
The prefered fix would be to convert the whole IR code to use the kernel IR
infrastructure (which wasn't available at the time this driver had been created).
Until anyone who still has this old hardware steps up an does the conversion,
fix it by not calling the symbol_request calls if the driver is compiled in
without the default IR symbols (CONFIG_DVB_USB_AF9005_REMOTE).
Due to the IR related pointers beeing NULL by default, IR support will then be disabled.
The downside of this solution is, that it will no longer be possible to
compile custom IR symbols (not using CONFIG_DVB_USB_AF9005_REMOTE) in.
Please note that this patch has NOT been tested with all possible cases.
I don't have the hardware and could only verify that it fixes the reported
bug.
Reported-by: Fengguag Wu <fengguang.wu@intel.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
DVBSky T9580 uses Integrated CX23885 IR controller to decode IR signal.
The IR type of DVBSky remote control is RC5.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add CI support for DVBSky T980C card. The new host device independent CIMaX SP2 I2C driver was used to implement it.
IRQ handling is not implemented at this point. It could be used to detect the CAM insertion/removal instantly.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
If the CI chip has an I2C driver, we need to store I2C client into state.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Improve debugging output.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Incorrect struct used in the SP2 driver.
Reported-by: Max Nibble <nibble.max@gmail.com>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds basic support for DVBSky T980C card. CI interface is not supported.
DVBSky T980C is a PCIe card with the following components:
- CX23885 PCIe bridge
- Si2168-A20 demodulator
- Si2158-A20 tuner
- CIMaX SP2 CI chip
The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI:
https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.html
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The au0828 quirks table is currently not in sync with the au0828
media driver.
Syncronize it and put them on the same order as found at au0828
driver, as all the au0828 devices with analog TV need the
same quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add a macro to simplify au0828 quirk table. That makes easier
to check it against the USB IDs at drivers/media/usb/au0828/au0828-cards.c.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Set the property for delivery system also in case of SYS_DVBC_ANNEX_B.
This behaviour is observed in the sniffs taken with Hauppauge HVR-955Q
Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This field is not used on this driver anymore. Remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch partially reverts 0fb220f2a5cb. What happened is
that the conversion of debug messages to use pr_debug() was a
bad idea, because one needing to debug would need to both
enable debug level via a modprobe parameter, and then to
enable the dynamic printk's.
So, for now, let's use printk() directly at dprintk().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
FE_SET_PROPERTY requires to open the devnode on R/W mode, or
otherwise it will fail. Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
dib7000p is for DVB, and not ISDB. So, there's no layer.
That removes this compilation warning:
drivers/media/dvb-frontends/dib7000p.c:1972: warning: 'i' is used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The warning is simple:
drivers/media/v4l2-core/v4l2-ctrls.c:1685:15: warning: incorrect type in assignment (different address spaces)
but the fix isn't.
The core problem was that the conversion from user to kernelspace was
done at too low a level and that needed to be moved up. That made it possible
to drop pointers to v4l2_ext_control from set_ctrl and validate_new and
clean up this sparse warning because those functions now always operate
on kernelspace pointers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch adds support for returning -ENODATA if the current
output doesn't support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch groups the v4l2_ioctl_ops.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
started
this patch uses vb2_is_busy() helper to check if streaming is
actually started, instead of driver managing it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch adds support for using vb2_ioctl_* helpers.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch converts the driver to use fh handling provided by the
v4l core instead of driver doing it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch teaches vpbe driver to use vb2_fop_mmap/poll helpers.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch improve vpbe_buffer_prepare() callback, as buf_prepare()
callback is never called with invalid state and check for
vb2_plane_vaddr(vb, 0) is dropped as payload check should
be done unconditionally.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch drops buf_cleanup() callback as this callback
is never called with buffer state active.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch makes use of vb2_ops_wait_prepare/finish helper functions.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
this patch moves the initialization of vb2 queue and the DMA
context to probe() and clean up in remove() callback respectively.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The NV12M is supported by all the version of MFC, so it is better
to use it as default OUTPUT format.
MFC v5 doesn't support NV21, I have tested it, for the SEC doc
it is not supported either.
Signed-off-by: ayaka <ayaka@soulik.info>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Patch b906352c2338 ([media] coda: dequeue buffers if start_streaming fails)
incorrectly marked buffers as DEQUEUED in case of start_streaming failure, when
in fact they should be set to QUEUED. The videobuf2 core warns about this.
Reported-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Interrupt result flags have to be cleared before a hardware job is run.
Otherwise, if they are cleared asynchronously, we may end up clearing them
after the interrupt for which we wanted to wait has already arrived, thus
overwriting the job results that we intended to wait for.
To prevent this, clear the flags only under hw_lock and before running
a hardware job.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
G_CTRL on V4L2_CID_MIN_BUFFERS_FOR_CAPTURE will fail if userspace happens to
query it after getting a resolution change event and before the codec has
a chance to parse the header and switch to an initialized state.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
