Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
|
|
if we have a !PM kernel build, our runtime
suspend/resume callbacks will be left defined but
unused. Add a ifdef CONFIG_PM guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e507 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In specific conditions (involving usb hubs) dwc2 devices can create a
lot of interrupts, even to the point of overwhelming devices running
at low frequencies. Some devices need to do special clock handling
at shutdown-time which may bring the system clock below the threshold
of being able to handle the dwc2 interrupts. Disabling dwc2-irqs
in a shutdown callbacks prevents reboots/poweroffs from getting stuck
in such cases.
The hsotg struct already contains an unused irq element, so we can
just use it to store the irq number for the shutdown callback.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The phy's init routine must be called before it can be used. Do so in
musb_init_controller and the matching shutdown in musb_remove.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Queue a request to disabled ep doesn't make sense, and induce caller
make mistakes.
Here is a example for the android mtp gadget function driver. A mem
corruption can happen on below senario.
1) On disconnect, mtp driver disable its EPs,
2) During send_file_work and receive_file_work, mtp queues a request
to ep. (The mtp driver need improve its synchronization logic!)
3) mtp_function_unbind is invoked and all mtp requests are freed.
4) when udc process the request queued on step 2, will cause kernel
NULL pointer dereference exception.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The "enumspd" field is located in register DSTS[2:1], but the code
which checks the bitfield does not shift the value accordingly. This
in turn causes incorrect detection of gadget link partner speed in
dwc2_hsotg_irq_enumdone() .
Shift the value accordingly to fix the problem with speed detection.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The
gadget_init function should not access any device registers because the
mode isn't guaranteed here.
Also, this is already called elsewhere before anything starts on the
gadget so it is not necessary here.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Reset already happens before this so just force the dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The delay for force mode is only 25ms according to the databook.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The dwc2_core_reset() function exists in the core so use that one
instead.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use the previously cached hw params in the gadget. This saves a reset
and force mode in the gadget initialization during probe and makes
getting the hardware parameters consistent between gadget and host.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Adds separate functions to get the host and device specific hardware
parameters. The functions check whether the parameters need to be read
at all, depending on dr_mode, and forces the mode only if necessary.
This saves some delays during probe. This also adds two device mode
parameters that will be used by the gadget.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added functions to set force mode for host and device. These functions
will check the current mode and only force if needed thus avoiding
unnecessary force mode delays. However clearing the mode is currently
done unconditionally and with the delay in place. This is needed during
the connector ID status change interrupt in order to ensure that the
mode has changed properly. This preserves the old behavior only for this
case. The warning comment about this is moved into the clear mode
condition.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The reset is required to get reset values of the hardware parameters but
the force mode is not. Move the base reset into dwc2_get_hwparams() and
do the reset and force mode afterwards.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
These functions should go in core.h where they can be called from core,
device, or host.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The dr_mode parameter was being checked against how the dwc2 module
was being configured at compile time. But it wasn't checked against
the hardware capabilities, nor were the hardware capabilities checked
against the compilation parameters.
This commit adds those checks and adjusts dr_mode to an appropriate
value, if needed. If the hardware capabilities and module compilation
do not match then we fail as it wouldn't be possible to run properly.
The hardware, module, and dr_mode, can each be set to host, device,
or otg. Check that all these values are compatible and adjust the
value of dr_mode if possible.
The following table summarizes the behavior:
actual
HW MOD dr_mode dr_mode
------------------------------
HST HST any : HST
HST DEV any : ---
HST OTG any : HST
DEV HST any : ---
DEV DEV any : DEV
DEV OTG any : DEV
OTG HST any : HST
OTG DEV any : DEV
OTG OTG any : dr_mode
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added functions to query the GHWCFG2.OTG_MODE. This tells us whether the
controller hardware is configured for OTG, device-only, or host-only.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
dwc2_core_reset() was previously renamed to
dwc2_core_reset_and_dr_force_mode(). Now add back dwc2_core_reset() which
performs only a basic core reset without forcing the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This
describes what it is doing more accurately. This is in preparation of
introducing a plain dwc2_core_reset() function that only performs the
reset and doesn't force the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
According to the databook, the core soft reset should be done before
checking for AHBIDLE. The gadget version of core reset had it correct
but the hcd version did not. This fixes the hcd version.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Calls to dwc2_core_reset() are currently very slow, taking at least
150ms (possibly more). It behooves us to take as many of these calls
out as possible.
It turns out that the calls in dwc2_fs_phy_init() and dwc2_hs_phy_init()
should (as documented in the code) only be needed if we need to do a PHY
SELECT. That means that if we see that we can avoid the PHY SELECT then
we can avoid the reset.
This patch appears to successfully bypass two resets (one per USB
device) on rk3288-based ARM Chromebooks.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
I found that the probe function of dwc2 driver takes much time
when kernel boot up. There are many long delays in the probe
function these take almost 1 second.
This patch trying to reduce unnecessary delay time.
In dwc2_core_reset() I see it use two at least 20ms delays to
wait AHB idle and core soft reset, but dwc2 data book said that
dwc2 core soft reset and AHB idle just need a few clocks (I think
it refers to AHB clock, and AHB clock run at 150MHz in my RK3288
board), so 20ms is too long, delay 1us for wait AHB idle and soft
reset is enough.
And in dwc2_get_hwparams() it takes 150ms to wait ForceHostMode
and ForceDeviceMode valid but in data book it said software must
wait at least 25ms before the change to take effect, so I reduce
this time to 25ms~50ms. By the way, is there any state bit show
that the force mode take effect ? Could we poll curmod bit for
figuring out if the change take effect ?
It seems that usleep_range() at boot time will pick the longest
value in the range. In dwc2_core_reset() there is a very long
delay takes 200ms, and this function run twice when probe, could
any one tell me is this delay time resonable ?
I have tried this patch in my RK3288-evb board. It works well.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On some host-only DWC2 ports (like the one in rk3288) when we set
GUSBCFG_FORCEHOSTMODE in GUSBCFG and then read back, we don't see the
bit set. Presumably that's because the port is always forced to HOST
mode so there's no reason to implement these status bits.
Since we know dwc2_core_reset() is always called before
dwc2_get_hwparams() and we know dwc2_core_reset() should have set
GUSBCFG_FORCEHOSTMODE whenever hsotg->dr_mode == USB_DR_MODE_HOST, we
can just check hsotg->dr_mode to decide that we can skip the delays in
dwc2_get_hwparams().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In (usb: dwc2: reset dwc2 core before dwc2_get_hwparams()) we added an
extra reset to the probe path for the dwc2 USB controllers. This
allowed proper detection of parameters even if the firmware had already
used the USB part.
Unfortunately, this extra reset is quite slow and is affecting boot
speed. We can avoid the double-reset by skipping the extra reset that
would happen just after the one we added. Logic that explains why this
is safe:
* As of the CL mentioned above, we now always call dwc2_core_reset() in
dwc2_driver_probe() before dwc2_hcd_init().
* The only caller of dwc2_hcd_init() is dwc2_driver_probe(), so we're
guaranteed that dwc2_core_reset() was called before dwc2_hdc_init().
* dwc2_hdc_init() is the only caller that passes an irq other than -1 to
dwc2_core_init(). Thus if dwc2_core_init() is called with an irq
other than -1 we're guaranteed that dwc2_core_reset was called before
dwc2_core_init().
...this allows us to remove the dwc2_core_reset() in dwc2_core_init() if
irq is not < 0.
Note that since "irq" wasn't used in the function dwc2_core_init()
anyway and since select_phy was always set at exactly the same times we
could avoid the reset, we remove "irq" and rename "select_phy" to
"initial_setup" and adjust the callers accordingly.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We initiate dwc2 usb controller in BIOS, dwc2_core_reset() should
be called before dwc2_get_hwparams() to reset core registers to
default value. Without this the FIFO setting might be incorrect
because calculating FIFO size need power-on value of
GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
This patch could avoid warnning massage like in rk3288 platform:
[ 2.074764] dwc2 ff580000.usb: 256 invalid for
host_perio_tx_fifo_size. Check HW configuration.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Previously dwc2_get_hwparams() was changing GUSBCFG and not putting it
back the way it was (specifically it set and cleared FORCEHOSTMODE).
Since we want to move dwc2_core_reset() _before_ dwc2_get_hwparams() we
should make sure dwc2_get_hwparams() isn't messing with things in a
permanent way.
Since we're now looking at GUSBCFG, it's obvious that we shouldn't need
all the extra delays if FORCEHOSTMODE was already set. This will avoid
some delays for any ports that have forced host mode.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When receiving GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt,
DCTL will be overwritten with DCTL_CGOUTNAK or DCTL_CGNPINNAK values.
Instead of overwriting it, write only needed bits.
It could cause an issue if GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF
interrupt is received after dwc2 disabled pullup by writing
DCTL_SFTDISCON bit.
Pullup will then be re-enabled whereas it should not.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
To stop an out endpoint, software should set sets the Global OUT NAK,
but not the Global Non-periodic IN NAK. This driver bug leads the out-ep
failed be in disabled state with below error.
dwc2_hsotg_ep_stop_xfr: timeout DOEPCTL.EPDisable
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It dose not work when we want to use the usb-to-serial port based
on one usb gadget as a console. Thus this patch adds the console
initialization to support this request.
To avoid the re-entrance when transferring data with usb endpoint,
it introduces a kthread to do the IO transmission.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We want the USB and PHY fixes in here as well to make things easier for
testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Late fixes for the RTC subsystem for 4.4:
A fix for a nasty hardware bug in rk808 and an initialization
reordering in da9063 to fix a possible crash"
* tag 'rtc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: da9063: fix access ordering error during RTC interrupt at system power on
rtc: rk808: Compensate for Rockchip calendar deviation on November 31st
|
|
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = devm_request_threaded_irq()
comes before
rtc->rtc_dev = devm_rtc_device_register();
In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc_dev.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.
This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty/serial driver fixes for 4.4-rc6 that resolve some
reported problems. All of these have been in linux-next. The details
are in the shortlog"
* tag 'tty-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix GPF in flush_to_ldisc()
serial: earlycon: Add missing spinlock initialization
serial: sh-sci: Fix length of scatterlist
n_tty: Fix poll() after buffer-limited eof push read
serial: 8250_uniphier: fix dl_read and dl_write functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.4-rc6. All of them resolve some
reported problems. Full details in the shortlog"
* tag 'usb-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: fix invalid memory access in hub_activate()
USB: ipaq.c: fix a timeout loop
phy: core: Get a refcount to phy in devm_of_phy_get_by_index()
phy: cygnus: pcie: add missing of_node_put
phy: miphy365x: add missing of_node_put
phy: miphy28lp: add missing of_node_put
phy: rockchip-usb: add missing of_node_put
phy: berlin-sata: add missing of_node_put
phy: mt65xx-usb3: add missing of_node_put
phy: brcmstb-sata: add missing of_node_put
phy: sun9i-usb: add USB dependency
|
|
Pull md fixes from Neil Brown:
"Four fixes for md:
- two recently introduced regressions fixed.
- one older bug in RAID10 - tagged for -stable since 4.2
- one minor sysfs api improvement"
* tag 'md/4.4-rc5-fixes' of git://neil.brown.name/md:
Fix remove_and_add_spares removes drive added as spare in slot_store
md: fix bug due to nested suspend
MD: change journal disk role to disk 0
md/raid10: fix data corruption and crash during resync
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Partial revert of "powerpc: Individual System V IPC system calls"
- pr_warn_once on unsupported OPAL_MSG type from Stewart
- Fix deadlock in opal-irqchip introduced by "Fix double endian
conversion" from Alistair
* tag 'powerpc-4.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/opal-irqchip: Fix deadlock introduced by "Fix double endian conversion"
powerpc/powernv: pr_warn_once on unsupported OPAL_MSG type
Partial revert of "powerpc: Individual System V IPC system calls"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of reference counting bugs here, one in spidev and one with
holding an extra reference in the core that we never freed if we
removed a device, plus a driver specific fix. Both of the refcounting
bugs are very old but they've only been found by observation so
hopefully their impact has been low"
* tag 'spi-fix-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fix parent-device reference leak
spi: spidev: Hold spi_lock over all defererences of spi in release()
spi-fsl-dspi: Fix CTAR Register access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.4 series. Most prominent: I revert the
error propagation from the .get() function until we can fix up all the
drivers properly for v4.5.
- Revert the error number propagation from the .get() vtable entry
temporarily, until we make the proper fixes to all drivers.
- Fix the clamping behaviour in the generic GPIO driver.
- Driver fix for the ath79 driver"
* tag 'gpio-v4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: revert get() to non-errorprogating behaviour
gpio: generic: clamp values from bgpio_get_set()
gpio: ath79: Fix the logic to clear offset bit of AR71XX_GPIO_REG_OE register
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for Freescale i.MX7D, Intel, Broadcom 2835
- One MAINTAINERS entry
* tag 'pinctrl-v4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
MAINTAINERS: pinctrl: Add maintainers for pinctrl-single
pinctrl: bcm2835: Fix initial value for direction_output
pinctrl: intel: fix offset calculation issue of register PAD_OWN
pinctrl: intel: fix bug of register offset calculation
pinctrl: freescale: add ZERO_OFFSET_VALID flag for vf610 pinctrl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A set of 'usual' driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rcar: disable runtime PM correctly in slave mode
i2c: designware: Keep pm_runtime_enable/_disable calls in sync
i2c: designware: fix IO timeout issue for AMD controller
i2c: imx: init bus recovery info before adding i2c adapter
i2c: do not use 0x in front of %pa
i2c: davinci: Increase module clock frequency
i2c: mv64xxx: The n clockdiv factor is 0 based on sunxi SoCs
i2c: rk3x: populate correct variable for sda_falling_time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a few assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - fix wake-on-touch
Input: elan_i2c - set input device's vendor and product IDs
Input: sun4i-lradc-keys - fix typo in binding documentation
Input: atmel_mxt_ts - add maxtouch to I2C table for module autoload
Input: arizona-haptic - fix disabling of haptics device
Input: aiptek - fix crash on detecting device without endpoints
Input: atmel_mxt_ts - add generic platform data for Chromebooks
Input: parkbd - clear unused function pointers
Input: walkera0701 - clear unused function pointers
Input: turbografx - clear unused function pointers
Input: gamecon - clear unused function pointers
Input: db9 - clear unused function pointers
|
|
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a potential regression introduced during the 4.3 cycle
(generic power domains framework), a nasty bug that has been present
forever (power capping RAPL driver), a build issue (Tegra cpufreq
driver) and a minor ugliness introduced recently (intel_pstate).
Specifics:
- Fix a potential regression in the generic power domains framework
introduced during the 4.3 development cycle that may lead to
spurious failures of system suspend in certain situations (Ulf
Hansson).
- Fix a problem in the power capping RAPL (Running Average Power
Limits) driver that causes it to initialize successfully on some
systems where it is not supposed to do that which is due to an
incorrect check in an initialization routine (Prarit Bhargava).
- Fix a build problem in the cpufreq Tegra driver that depends on the
regulator framework, but that dependency is not reflected in
Kconfig (Arnd Bergmann).
- Fix a recent mistake in the intel_pstate driver where a numeric
constant is used directly instead of a symbol defined specifically
for the case in question (Prarit Bhargava)"
* tag 'pm+acpi-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: fix BIOS lock check
cpufreq: intel_pstate: Minor cleanup for FRAC_BITS
cpufreq: tegra: add regulator dependency for T124
PM / Domains: Allow runtime PM callbacks to be re-used during system PM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes this time, two in SES picked up by KASAN for various types
of buffer overrun. The first is a USB array which returns page 8
whatever is asked for and causes us to overrun with incorrect data
format assumptions and the second is an invalid iteration of page 10
(the additional information page).
The final fix is a reversion of a NULL deref fix which caused
suspend/resume not to be called in pairs leading to incorrect device
operation (Jens has queued a more proper fix for the problem in
block)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ses: fix additional element traversal bug
Revert "SCSI: Fix NULL pointer dereference in runtime PM"
ses: Fix problems with simple enclosures
|
|
When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|