| Age | Commit message (Collapse) | Author |
|---|
|
Casting away const is bad practice. Since this is ARM specific driver
don't have hardware actually test this.
Having getter functions for ops is really unnecessary code bloat, but
not going to touch that.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vivien Didelot says:
====================
net: dsa: add MDB support
This patchset adds the switchdev MDB object support to the DSA layer.
The MDB support for the mv88e6xxx driver is very similar to the FDB
support. The FDB operations care about unicast addresses while the MDB
operations care about multicast addresses.
Both operation set load/purge/dump the Address Translation Table (ATU),
thus common code is used.
Changes in v2 based on Andrew's comments:
- drop "group" in multicast database related doc and comment
- change _one for more relevant _fid in mv88e6xxx_port_db_dump_one
- return -EOPNOTSUPP if switchdev obj ID is neither _FDB nor _MDB
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the MDB operations. This consists of
loading/purging/dumping multicast addresses for a given port in the ATU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDB support for the mv88e6xxx driver will be very similar to the FDB
support, since it consists of loading/purging/dumping address to/from
the Address Translation Unit (ATU).
Prepare the support for MDB by making the FDB code accessing the ATU
generic. The FDB operations now provide access to the unicast addresses
while the MDB operations will provide access to the multicast addresses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SWITCHDEV_OBJ_ID_PORT_MDB support to the DSA layer.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Raghu Vatsavayi says:
====================
liquidio CN23XX support
Following patchset adds support for new device "CN23XX" in
liquidio family of adapters. As adviced by you I have split
the previous V3 patch of 18 patches into two halves. This
first patchset has first 10 patches, which are tested against
net-next. I will post the second half after this one.
This V4 patch also addressed all the comments from previous
submission:
1) Avoid busy loop while reading registers.
2) Other minor comments about debug messages and constants.
Please apply patches in following order as some of the
patches depend on earlier patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add firmware download support for cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support msix interrupt for cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for cn23xx queue manipulation.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for initializing cn23xx device registers
related to mac, input/output and pf global config.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for cn23xx device init and sriov queue config.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for cn23xx specific queue definitions and
features.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds register definitions and structures for new
device cn23xx.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support of common irq enable functionality for both
iq(instruction queue) and oq(output queue).
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch contains changes for firmware version management.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Consolidate common functionality of various devices
from different files into lio_core.c/octeon_console.c.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The addition of the per-queue statistics introduced a harmless warning
on all 32-bit architectures:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function 'qede_get_ethtool_stats':
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
This changes the cast to 'void *' to shut up the warning, which
avoids the assumptions on the size of the pointer type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68db9ec2df07 ("qede: Add support for per-queue stats.")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PM_SLEEP is disabled, we get a couple of harmless warnings:
drivers/net/ethernet/renesas/ravb_main.c:2117:12: error: 'ravb_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/renesas/ravb_main.c:2104:12: error: 'ravb_suspend' defined but not used [-Werror=unused-function]
The simplest solution here is to replace the #ifdef with __maybe_unused
annotations, which lets the compiler do the right thing by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0184165b2f42 ("ravb: add sleep PM suspend/resume support")
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Ahern says:
====================
net: mpls: fragmentation and gso fixes for locally originated traffic
This series fixes mtu and fragmentation for tunnels using lwtunnel
output redirect, and fixes GSO for MPLS for locally originated traffic
reported by Lennert Buytenhek.
A follow on series will address fragmentation and GSO for forwarded
MPLS traffic. Hardware offload of GSO with MPLS also needs to be
addressed.
Simon: Can you verify this works with OVS for single and multiple
labels?
v4
- more updates to mpls_gso_segment per Alex's comments (thanks, Alex)
- updates to teaching OVS about marking MPLS labels as the network header
v3
- updates to mpls_gso_segment per Alex's comments
- dropped skb->encapsulation = 1 from mpls_xmit per Alex's comment
v2
- consistent use of network_header in skb to fix GSO for MPLS
- update MPLS code in OVS to network_header and inner_network_header
====================
Tested-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
veth does not really transmit packets only moves the skb from one
netdev to another so gso and checksum is not really needed. Add
the features to mpls_features to get the same benefit and performance
with MPLS as without it.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Lennert the MPLS GSO code is failing to properly segment
large packets. There are a couple of problems:
1. the inner protocol is not set so the gso segment functions for inner
protocol layers are not getting run, and
2 MPLS labels for packets that use the "native" (non-OVS) MPLS code
are not properly accounted for in mpls_gso_segment.
The MPLS GSO code was added for OVS. It is re-using skb_mac_gso_segment
to call the gso segment functions for the higher layer protocols. That
means skb_mac_gso_segment is called twice -- once with the network
protocol set to MPLS and again with the network protocol set to the
inner protocol.
This patch sets the inner skb protocol addressing item 1 above and sets
the network_header and inner_network_header to mark where the MPLS labels
start and end. The MPLS code in OVS is also updated to set the two
network markers.
>From there the MPLS GSO code uses the difference between the network
header and the inner network header to know the size of the MPLS header
that was pushed. It then pulls the MPLS header, resets the mac_len and
protocol for the inner protocol and then calls skb_mac_gso_segment
to segment the skb.
Afterward the inner protocol segmentation is done the skb protocol
is set to mpls for each segment and the network and mac headers
restored.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 145dd5f9c88f ("net: flush the softnet backlog in process
context"), we can easily batch calls to flush_all_backlogs() for all
devices processed in rollback_registered_many()
Tested:
Before patch, on an idle host.
modprobe dummy numdummies=10000
perf stat -e context-switches -a rmmod dummy
Performance counter stats for 'system wide':
1,211,798 context-switches
1.302137465 seconds time elapsed
After patch:
perf stat -e context-switches -a rmmod dummy
Performance counter stats for 'system wide':
225,523 context-switches
0.721623566 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove a useless log message and improve the logic for setting
a PHY address from the contents of the MNG_IF_SEL register.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Preparation for removal of use of skbs from AFS
Here's a set of patches that prepare the way for the removal of the use of
sk_buffs from fs/afs (they'll be entirely retained within net/rxrpc):
(1) Fix a potential NULL-pointer deref in rxrpc_abort_calls().
(2) Condense all the terminal call state machine states to a single one
plus supplementary info.
(3) Add a trace point for rxrpc call usage debugging.
(4) Cleanups and missing headers.
(5) Provide a way for AFS to ask about a call's peer address without
having an sk_buff to query.
(6) Use call->peer directly rather than going via call->conn (which might
be NULL).
(7) Pass struct socket * to various rxrpc kernel interface functions so
they can use that directly rather than getting it from the rxrpc_call
struct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in dev_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass struct socket * to more rxrpc kernel interface functions. They should
be starting from this rather than the socket pointer in the rxrpc_call
struct if they need to access the socket.
I have left:
rxrpc_kernel_is_data_last()
rxrpc_kernel_get_abort_code()
rxrpc_kernel_get_error_number()
rxrpc_kernel_free_skb()
rxrpc_kernel_data_consumed()
unmodified as they're all about to be removed (and, in any case, don't
touch the socket).
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Use call->peer rather than call->conn->params.peer as call->conn may become
NULL.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Provide a function so that kernel users, such as AFS, can ask for the peer
address of a call:
void rxrpc_kernel_get_peer(struct rxrpc_call *call,
struct sockaddr_rxrpc *_srx);
In the future the kernel service won't get sk_buffs to look inside.
Further, this allows us to hide any canonicalisation inside AF_RXRPC for
when IPv6 support is added.
Also propagate this through to afs_find_server() and issue a warning if we
can't handle the address family yet.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
We should #include linux/random.h to use get_random().
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Remove one #ifndef'd-out variable and a couple of excessive blank lines.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add a trace event for debuging rxrpc_call struct usage.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Condense the terminal states of a call state machine to a single state,
plus a separate completion type value. The value is then set, along with
error and abort code values, only when the call is transitioned to the
completion state.
Helpers are provided to simplify this.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
The call pointer in a channel on a connection will be NULL if there's no
active call on that channel. rxrpc_abort_calls() needs to check for this
before trying to take the call's state_lock.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-08-29
This series contains updates to fm10k only.
Jake provides all the changes in this series starting with fixes an issue
where VF devices may fail during an unbind/bind and we will never zero
the reference counter for the pci_dev structure. Updated the hot path
to use SW counters instead of checking for hardware Tx pending for
possible transmit hangs, which will improve performance. Fixed the NAPI
budget accounting so that fm10k_poll will return actual work done,
capped at (budget - 1) instead of returning 0. Added a check to ensure
that the device is in the normal IO state before continuing to probe,
which allows us to give a more descriptive message of what is wrong
in the case of uncorrectable AER error. In preparation for adding Geneve
Rx offload support, refactored the current VXLAN offload flow to be a bit
more generic. Added support for receive offloads on one Geneve tunnel.
Ensure that other bits in the RXQCTL register do not get cleared, to
make sure that bits related to queue ownership are maintained. Fixed
an issue in queue ownership assignment which casued a race condition
between the PF and the VF such that potentially a VF could cause FUM
fault errors due to normal PF/VF driver behavior.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All three conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Add missing sysfs attribute group terminator to it87 driver"
* tag 'hwmon-for-linus-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (it87) Add missing sysfs attribute group terminator
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix bugs that could cause kernel deadlocks or file system corruption
while moving xattrs to expand the extended inode.
Also add some sanity checks to the block group descriptors to make
sure we don't end up overwriting the superblock"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid deadlock when expanding inode size
ext4: properly align shifted xattrs when expanding inodes
ext4: fix xattr shifting when expanding inodes part 2
ext4: fix xattr shifting when expanding inodes
ext4: validate that metadata blocks do not overlap superblock
ext4: reserve xattr index for the Hurd
|
|
Pull networking fixes from David Miller:
1) Segregate namespaces properly in conntrack dumps, from Liping Zhang.
2) tcp listener refcount fix in netfilter tproxy, from Eric Dumazet.
3) Fix timeouts in qed driver due to xmit_more, from Yuval Mintz.
4) Fix use-after-free in tcp_xmit_retransmit_queue().
5) Userspace header fixups (use of __u32, missing includes, etc.) from
Mikko Rapeli.
6) Further refinements to fragmentation wrt gso and tunnels, from
Shmulik Ladkani.
7) Trigger poll correctly for zero length UDP packets, from Eric
Dumazet.
8) TCP window scaling fix, also from Eric Dumazet.
9) SLAB_DESTROY_BY_RCU is not relevant any more for UDP sockets.
10) Module refcount leak in qdisc_create_dflt(), from Eric Dumazet.
11) Fix deadlock in cp_rx_poll() of 8139cp driver, from Gao Feng.
12) Memory leak in rhashtable's alloc_bucket_locks(), from Eric Dumazet.
13) Add new device ID to alx driver, from Owen Lin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
Add Killer E2500 device ID in alx driver.
net: smc91x: fix SMC accesses
Documentation: networking: dsa: Remove platform device TODO
net/mlx5: Increase number of ethtool steering priorities
net/mlx5: Add error prints when validate ETS failed
net/mlx5e: Fix memory leak if refreshing TIRs fails
net/mlx5e: Add ethtool counter for TX xmit_more
net/mlx5e: Fix ethtool -g/G rx ring parameter report with striding RQ
net/mlx5e: Don't wait for SQ completions on close
net/mlx5e: Don't post fragmented MPWQE when RQ is disabled
net/mlx5e: Don't wait for RQ completions on close
net/mlx5e: Limit UMR length to the device's limitation
rhashtable: fix a memory leak in alloc_bucket_locks()
sfc: fix potential stack corruption from running past stat bitmask
team: loadbalance: push lacpdus to exact delivery
net: hns: dereference ppe_cb->ppe_common_cb if it is non-null
8139cp: Fix one possible deadloop in cp_rx_poll
i40e: Change some init flow for the client
Revert "phy: IRQ cannot be shared"
net: dsa: bcm_sf2: Fix race condition while unmasking interrupts
...
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Remove module related code from two drivers that are only configurable
as built-in: intel_pmic_gpio and platform/olpc"
* tag 'platform-drivers-x86-v4.8-4' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_pmic_gpio: Make explicitly non-modular
platform/olpc: Make ec explicitly non-modular
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Ben Herrenschmidt:
"This was meant to be sent early last week, but I has a change pending
on one of the fixes and other things made me forget all about. Ugh.
We have some misc fixes for powerpc 4.8. Some trivial bits and some
regressions, and a trivial cleanup or two that I saw no point in
letting rot in patchwork"
* tag 'powerpc-4.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: signals: Discard transaction state from signal frames
powerpc/powernv : Drop reference added by kset_find_obj()
powerpc/tm: do not use r13 for tabort_syscall
powerpc: move hmi.c to arch/powerpc/kvm/
powerpc: sysdev: cpm: fix gpio save_regs functions
powerpc/pseries: PACA save area fix for MCE vs MCE
powerpc/pseries: PACA save area fix for general exception vs MCE
powerpc/prom: Fix sub-processor option passed to ibm, client-architecture-support
powerpc, hotplug: Avoid to touch non-existent cpumasks.
powerpc: migrate exception table users off module.h and onto extable.h
powerpc/powernv/pci: fix iterator signedness
powerpc/pseries: use pci_host_bridge.release_fn() to kfree(phb)
cxl: use pcibios_free_controller_deferred() when removing vPHBs
powerpc: mpc8349emitx: Delete unnecessary assignment for the field "owner"
powerpc/512x: Delete unnecessary assignment for the field "owner"
drivers/macintosh: Delete owner assignment
powerpc: cputhreads: Add missing include file
|
|
Attribute array it87_attributes_in lacks its NULL terminator,
causing random behavior when operating on the attribute group.
Fixes: 52929715634a ("hwmon: (it87) Use is_visible for voltage sensors")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When the PF assigns a new MAC address to a VF it uses the base address
registers to store the MAC address. This allows a VF which loads after
this setup the ability to get the initial address without having to wait
for a mailbox message. Unfortunately to do this, the PF must take queue
ownership away from the VF, which can cause fault errors when there is
already an active VF driver.
This queue ownership assignment causes race condition between the PF and
the VF such that potentially a VF can cause FUM fault errors due to
normal PF/VF driver behavior.
It is not safe to simply allow the PF to write the base address
registers without taking queue ownership back as the PF must also
disable the queues, and this would impact active VF use. The current
code is safe because the queue ownership will prevent the VF from
actually writing but does trigger the FUM fault.
We can do better by simply avoiding the register write process when
a mailbox message suffices. If the message can be sent over the mailbox,
then we will not perform the queue ownership assignment and we won't
update the base address to be the same as the MAC address.
We do still have to write the TXQCTL registers in order to update the
VID of the queue. This is necessary because the TXQCTL register is
read-only from the VF, and thus the VF cannot do this for itself. This
register does not need to wait for the Tx queue to be disabled and is
safe for the PF to write during normal VF operation, so we move this
write to the top of the function above the mailbox message. Without
this, the TXQCTL register would be misconfigured and cause the VF to Tx
hang.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Ensure that other bits in the RXQCTL register do not get cleared. This
ensures that bits related to queue ownership are maintained.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
