| Age | Commit message (Collapse) | Author |
|---|
|
commit 0bdbf3b071986ba80731203683cf623d5c0cacb1 upstream.
The IRQFD framework calls the architecture dependent function
twice if the corresponding GSI type is edge triggered. For ARM,
the function kvm_set_msi() is getting called twice whenever the
IRQFD receives the event signal. The rest of the code path is
trying to inject the MSI without any validation checks. No need
to call the function vgic_its_inject_msi() second time to avoid
an unnecessary overhead in IRQ queue logic. It also avoids the
possibility of VM seeing the MSI twice.
Simple fix, return -1 if the argument 'level' value is zero.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d0928f18bf890d2853281f59aba0dd5a46b34f9 upstream.
Since it was introduced in commit da8d02d19ffdd201 ("arm64/capabilities:
Make use of system wide safe value"), __raw_read_system_reg() has
erroneously mapped some sysreg IDs to other registers.
For the fields in ID_ISAR5_EL1, our local feature detection will be
erroneous. We may spuriously detect that a feature is uniformly
supported, or may fail to detect when it actually is, meaning some
compat hwcaps may be erroneous (or not enforced upon hotplug).
This patch corrects the erroneous entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: da8d02d19ffdd201 ("arm64/capabilities: Make use of system wide safe value")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adbe7e26f4257f72817495b9bce114284060b0d7 upstream.
When bypassing SWIOTLB on small-memory systems, we need to avoid calling
into swiotlb_dma_mapping_error() in exactly the same way as we avoid
swiotlb_dma_supported(), because the former also relies on SWIOTLB state
being initialised.
Under the assumptions for which we skip SWIOTLB, dma_map_{single,page}()
will only ever return the DMA-offset-adjusted physical address of the
page passed in, thus we can report success unconditionally.
Fixes: b67a8b29df7e ("arm64: mm: only initialize swiotlb when necessary")
CC: Jisheng Zhang <jszhang@marvell.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f36ebaf21fdae99c091c67e8b6fab33969f2667 upstream.
When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.
But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.
The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.
Fixes: 2d58b733c876 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58ab9a088ddac4efe823471275859d64f735577e upstream.
Kirill reported a warning from UBSAN about undefined behavior when using
protection keys. He is running on hardware that actually has support for
it, which is not widely available.
The warning triggers because of very large shifts of integers when doing a
pkey_free() of a large, invalid value. This happens because we never check
that the pkey "fits" into the mm_pkey_allocation_map().
I do not believe there is any danger here of anything bad happening
other than some aliasing issues where somebody could do:
pkey_free(35);
and the kernel would effectively execute:
pkey_free(8);
While this might be confusing to an app that was doing something stupid, it
has to do something stupid and the effects are limited to the app shooting
itself in the foot.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Cc: kirill.shutemov@linux.intel.com
Link: http://lkml.kernel.org/r/20170223222603.A022ED65@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e38bea99a80eab408adee27f873a188d57b76cb upstream.
fuse_file_put() was missing the "force" flag for the RELEASE request when
sending synchronously (fuseblk).
If this flag is not set, then a sync request may be interrupted before it
is dequeued by the userspace filesystem. In this case the OPEN won't be
balanced with a RELEASE.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 5a18ec176c93 ("fuse: fix hang of single threaded fuseblk filesystem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c68bb0f62bf8de8bb30123ea840d5168f25abea upstream.
Running with KASAN and crypto tests currently gives
BUG: KASAN: global-out-of-bounds in __test_aead+0x9d9/0x2200 at addr ffffffff8212fca0
Read of size 16 by task cryptomgr_test/1107
Address belongs to variable 0xffffffff8212fca0
CPU: 0 PID: 1107 Comm: cryptomgr_test Not tainted 4.10.0+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
Call Trace:
dump_stack+0x63/0x8a
kasan_report.part.1+0x4a7/0x4e0
? __test_aead+0x9d9/0x2200
? crypto_ccm_init_crypt+0x218/0x3c0 [ccm]
kasan_report+0x20/0x30
check_memory_region+0x13c/0x1a0
memcpy+0x23/0x50
__test_aead+0x9d9/0x2200
? kasan_unpoison_shadow+0x35/0x50
? alg_test_akcipher+0xf0/0xf0
? crypto_skcipher_init_tfm+0x2e3/0x310
? crypto_spawn_tfm2+0x37/0x60
? crypto_ccm_init_tfm+0xa9/0xd0 [ccm]
? crypto_aead_init_tfm+0x7b/0x90
? crypto_alloc_tfm+0xc4/0x190
test_aead+0x28/0xc0
alg_test_aead+0x54/0xd0
alg_test+0x1eb/0x3d0
? alg_find_test+0x90/0x90
? __sched_text_start+0x8/0x8
? __wake_up_common+0x70/0xb0
cryptomgr_test+0x4d/0x60
kthread+0x173/0x1c0
? crypto_acomp_scomp_free_ctx+0x60/0x60
? kthread_create_on_node+0xa0/0xa0
ret_from_fork+0x2c/0x40
Memory state around the buggy address:
ffffffff8212fb80: 00 00 00 00 01 fa fa fa fa fa fa fa 00 00 00 00
ffffffff8212fc00: 00 01 fa fa fa fa fa fa 00 00 00 00 01 fa fa fa
>ffffffff8212fc80: fa fa fa fa 00 05 fa fa fa fa fa fa 00 00 00 00
^
ffffffff8212fd00: 01 fa fa fa fa fa fa fa 00 00 00 00 01 fa fa fa
ffffffff8212fd80: fa fa fa fa 00 00 00 00 00 05 fa fa fa fa fa fa
This always happens on the same IV which is less than 16 bytes.
Per Ard,
"CCM IVs are 16 bytes, but due to the way they are constructed
internally, the final couple of bytes of input IV are dont-cares.
Apparently, we do read all 16 bytes, which triggers the KASAN errors."
Fix this by padding the IV with null bytes to be at least 16 bytes.
Fixes: 0bc5a6c5c79a ("crypto: testmgr - Disable rfc4309 test and convert test vectors")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa33b9b9a2ebb00d33c83a5312d4fbf2d5aeba36 upstream.
If dso__load_kcore frees all of the existing maps, but one has already
been attached to a callchain cursor node, then we can get a SIGSEGV in
any function that happens to try to use this invalid cursor. Use the
existing map refcount mechanism to forestall cleanup of a map until the
cursor iterates past the node.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 84c2cafa2889 ("perf tools: Reference count struct map")
Link: http://lkml.kernel.org/r/20170106062331.GB2707@templeofstupid.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0bb03924f1a80e7f65900e36c8e6b3dc167c5f8 upstream.
DoS protection conditions were altered in WS2016 and now it's easy to get
-EAGAIN returned from vmbus_post_msg() (e.g. when we try changing MTU on a
netvsc device in a loop). All vmbus_post_msg() callers don't retry the
operation and we usually end up with a non-functional device or crash.
While host's DoS protection conditions are unknown to me my tests show that
it can take up to 10 seconds before the message is sent so doing udelay()
is not an option, we really need to sleep. Almost all vmbus_post_msg()
callers are ready to sleep but there is one special case:
vmbus_initiate_unload() which can be called from interrupt/NMI context and
we can't sleep there. I'm also not sure about the lonely
vmbus_send_tl_connect_request() which has no in-tree users but its external
users are most likely waiting for the host to reply so sleeping there is
also appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a7275a3d867b228216886aae35e1f64291180b1 upstream.
eb5767122feb ("PCI: altera: Simplify TLB_CFG_DW0 usage") used
TLP_FMTTYPE_CFGRD* (instead of TLP_FMTTYPE_CFGWR*) for TLP writes, which
causes writing to configuration space to fail. Fix it by using correct
FMTTYPE for write operation.
Fixes: eb5767122feb ("PCI: altera: Simplify TLB_CFG_DW0 usage")
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49f4b08e61547a5ccd2db551d994c4503efe5666 upstream.
pnv_php_disable_irq() can be called in two paths: Bailing path in
pnv_php_enable_irq() or releasing slot. The MSI (or MSIx) interrupts
is disabled unconditionally in pnv_php_disable_irq(). It's wrong
because that might be enabled by drivers other than pnv-php.
This disables MSI (or MSIx) interrupts and the PCI device only if
it was enabled by pnv-php. In the error path of pnv_php_enable_irq(),
we rely on the newly added parameter @disable_device. In the path
of releasing slot, @pnv_php->irq is checked.
Fixes: 360aebd85a4c ("drivers/pci/hotplug: Support surprise hotplug in powernv driver")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60e2e2fbafdd1285ae1b4ad39ded41603e0c74d0 upstream.
The devfn of 00:02.0 is 0x10. devfn_to_wslot(0x10) == 0x2, and
wslot_to_devfn(0x2) should be 0x10, while it's 0x2 in the current code.
Due to this, hv_eject_device_work() -> pci_get_domain_bus_and_slot()
returns NULL and pci_stop_and_remove_bus_device() is not called.
Later when the real device driver's .remove() is invoked by
hv_pci_remove() -> pci_stop_root_bus(), some warnings can be noticed
because the VM has lost the access to the underlying device at that
time.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
CC: K. Y. Srinivasan <kys@microsoft.com>
CC: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9f1e32600816d695f817477d56490bfc2ba43c6 upstream.
This patch fixes the OTP register definitions for the AR934x and AR9550
WMAC SoC.
Previously, the ath9k driver was unable to initialize the integrated
WMAC on an Aerohive AP121:
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: Unable to initialize hardware; initialization status: -5
| ath9k ar934x_wmac: failed to initialize device
| ath9k: probe of ar934x_wmac failed with error -5
It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA
definitions contain a typo.
Cc: Gabor Juhos <juhosg@openwrt.org>
Fixes: add295a4afbdf5852d0 "ath9k: use correct OTP register offsets for AR9550"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a5e969bb2f6692a256352649355d56d018d6b88 upstream.
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a70e1d6fd6b5e1a81fa6171600942bee34f5128f upstream.
Simply return -EOPNOTSUPP instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb4281528b62207918b1e95827cad7527aa4dbaa upstream.
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb97fbbcac15982406e0c74cd5512a8b6fcf10b3 upstream.
Parallel reads from multiple threads on a file descriptor
are not well defined and racy. It is safer to return to original
behavior and simply fail the additional read.
The solution is to remove request for next read credit.
Fixes: ff1586a7ea57 ("mei: enqueue consecutive reads")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 916cafdc95843fb9af5fd5f83ca499d75473d107 upstream.
There were some bugs in the JNE64 and JLT64 comparision macros. This fixes
them, improves comments, and cleans up the file while we are at it.
Reported-by: Stephen Röttger <sroettger@google.com>
Signed-off-by: Mathias Svensson <idolf@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4753d8a24d4588657bc0a4cd66d4e282dff15c8c upstream.
If the file system requires journal recovery, and the device is
read-ony, return EROFS to the mount system call. This allows xfstests
generic/050 to pass.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97abd7d4b5d9c48ec15c425485f054e1c15e591b upstream.
If the journal is aborted, the needs_recovery feature flag should not
be removed. Otherwise, it's the journal might not get replayed and
this could lead to more data getting lost.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb5efbcb762aee4b454b04f7115f73ccbcf8f0ef upstream.
The write_end() function must always unlock the page and drop its ref
count, even on an error.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd01b690f8f4b1e414f89e5a9a5326bf720d6652 upstream.
In the case where the child's encryption context was inconsistent with
its parent directory, we were using inode->i_sb and inode->i_ino after
the inode had already been iput(). Fix this by doing the iput() in the
correct places.
Note: only ext4 had this bug, not f2fs and ubifs.
Fixes: d9cdc9033181 ("ext4 crypto: enforce context consistency")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b136499e906460919f0d21a49db1aaccf0ae963 upstream.
ext4_journalled_write_end() did not propely handle all the cases when
generic_perform_write() did not copy all the data into the target page
and could mark buffers with uninitialized contents as uptodate and dirty
leading to possible data corruption (which would be quickly fixed by
generic_perform_write() retrying the write but still). Fix the problem
by carefully handling the case when the page that is written to is not
uptodate.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd648b8a8fd5071d232242d5ee7ee3c0815776af upstream.
If filesystem groups are artifically small (using parameter -g to
mkfs.ext4), ext4_mb_normalize_request() can result in a request that is
larger than a block group. Trim the request size to not confuse
allocation code.
Reported-by: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03e916fa8b5577d85471452a3d0c5738aa658dae upstream.
Inside ext4_ext_shift_extents() function ext4_find_extent() is called
without EXT4_EX_NOCACHE flag, which should prevent cache population.
This leads to oudated offsets in the extents tree and wrong blocks
afterwards.
Patch fixes the problem providing EXT4_EX_NOCACHE flag for each
ext4_find_extents() call inside ext4_ext_shift_extents function.
Fixes: 331573febb6a2
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a9b8cba62c0741109c33a2be700ff3d7703a7c2 upstream.
While doing 'insert range' start block should be also shifted right.
The bug can be easily reproduced by the following test:
ptr = malloc(4096);
assert(ptr);
fd = open("./ext4.file", O_CREAT | O_TRUNC | O_RDWR, 0600);
assert(fd >= 0);
rc = fallocate(fd, 0, 0, 8192);
assert(rc == 0);
for (i = 0; i < 2048; i++)
*((unsigned short *)ptr + i) = 0xbeef;
rc = pwrite(fd, ptr, 4096, 0);
assert(rc == 4096);
rc = pwrite(fd, ptr, 4096, 4096);
assert(rc == 4096);
for (block = 2; block < 1000; block++) {
rc = fallocate(fd, FALLOC_FL_INSERT_RANGE, 4096, 4096);
assert(rc == 0);
for (i = 0; i < 2048; i++)
*((unsigned short *)ptr + i) = block;
rc = pwrite(fd, ptr, 4096, 4096);
assert(rc == 4096);
}
Because start block is not included in the range the hole appears at
the wrong offset (just after the desired offset) and the following
pwrite() overwrites already existent block, keeping hole untouched.
Simple way to verify wrong behaviour is to check zeroed blocks after
the test:
$ hexdump ./ext4.file | grep '0000 0000'
The root cause of the bug is a wrong range (start, stop], where start
should be inclusive, i.e. [start, stop].
This patch fixes the problem by including start into the range. But
not to break left shift (range collapse) stop points to the beginning
of the a block, not to the end.
The other not obvious change is an iterator check on validness in a
main loop. Because iterator is unsigned the following corner case
should be considered with care: insert a block at 0 offset, when stop
variables overflows and never becomes less than start, which is 0.
To handle this special case iterator is set to NULL to indicate that
end of the loop is reached.
Fixes: 331573febb6a2
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e02898b423802b1f3a3aaa7f16e896da069ba8f7 upstream.
loop_reread_partitions() needs to do I/O, but we just froze the queue,
so we end up waiting forever. This can easily be reproduced with losetup
-P. Fix it by moving the reread to after we unfreeze the queue.
Fixes: ecdd09597a57 ("block/loop: fix race between I/O and set_status")
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ecdd09597a57251323b0de50e3d45e69298c4a83 upstream.
Inside set_status, transfer need to setup again, so
we have to drain IO before the transition, otherwise
oops may be triggered like the following:
divide error: 0000 [#1] SMP KASAN
CPU: 0 PID: 2935 Comm: loop7 Not tainted 4.10.0-rc7+ #213
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
task: ffff88006ba1e840 task.stack: ffff880067338000
RIP: 0010:transfer_xor+0x1d1/0x440 drivers/block/loop.c:110
RSP: 0018:ffff88006733f108 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8800688d7000 RCX: 0000000000000059
RDX: 0000000000000000 RSI: 1ffff1000d743f43 RDI: ffff880068891c08
RBP: ffff88006733f160 R08: ffff8800688d7001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800688d7000
R13: ffff880067b7d000 R14: dffffc0000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88006d000000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000006c17e0 CR3: 0000000066e3b000 CR4: 00000000001406f0
Call Trace:
lo_do_transfer drivers/block/loop.c:251 [inline]
lo_read_transfer drivers/block/loop.c:392 [inline]
do_req_filebacked drivers/block/loop.c:541 [inline]
loop_handle_cmd drivers/block/loop.c:1677 [inline]
loop_queue_work+0xda0/0x49b0 drivers/block/loop.c:1689
kthread_worker_fn+0x4c3/0xa30 kernel/kthread.c:630
kthread+0x326/0x3f0 kernel/kthread.c:227
ret_from_fork+0x31/0x40 arch/x86/entry/entry_64.S:430
Code: 03 83 e2 07 41 29 df 42 0f b6 04 30 4d 8d 44 24 01 38 d0 7f 08
84 c0 0f 85 62 02 00 00 44 89 f8 41 0f b6 48 ff 25 ff 01 00 00 99 <f7>
7d c8 48 63 d2 48 03 55 d0 48 89 d0 48 89 d7 48 c1 e8 03 83
RIP: transfer_xor+0x1d1/0x440 drivers/block/loop.c:110 RSP:
ffff88006733f108
---[ end trace 0166f7bd3b0c0933 ]---
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e112666b4959b25a8552d63bc564e1059be703e8 upstream.
If the journal has been aborted, we shouldn't mark the underlying
buffer head as dirty, since that will cause the metadata block to get
modified. And if the journal has been aborted, we shouldn't allow
this since it will almost certainly lead to a corrupted file system.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 907565337ebf998a68cb5c5b2174ce5e5da065eb upstream.
Userspace applications should be allowed to expect the membarrier system
call with MEMBARRIER_CMD_SHARED command to issue memory barriers on
nohz_full CPUs, but synchronize_sched() does not take those into
account.
Given that we do not want unrelated processes to be able to affect
real-time sensitive nohz_full CPUs, simply return ENOSYS when membarrier
is invoked on a kernel with enabled nohz_full CPUs.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b0408745e7ff24757cbfd571d69026c0ddb803c upstream.
LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the
proper power off sequence is used before shutting down the platform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 857de6e00778738dc3d61f75acbac35bdc48e533 upstream.
The device handler needs to check if a given queue belongs to a scsi
device; only then does it make sense to attach a device handler.
[mkp: dropped flags]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c421530bf848604e97d0785a03b3fe2c62775083 upstream.
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb835223752 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40630f462824ee24bc00d692865c86c3828094e0 upstream.
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bba5dc332ec2d3a685cb4dae668c793f6a3713a3 upstream.
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3cd6d3d9b1abab8dcdf0800224ce26daac24eea2 upstream.
Properly set SRB flags when hosting device supports tagged queuing.
This patch improves the performance on Fiber Channel disks.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d36a19541fe8f392778ac137d60f9be8dfdd8f9d upstream.
The lvm2 sequence to manage dm-raid constructor flags that trigger a
rebuild or a reshape is defined as:
1) load table with flags (e.g. rebuild/delta_disks/data_offset)
2) clear out the flags in lvm2 metadata
3) store the lvm2 metadata, reload the table to reset the flags
previously established during the initial load (1) -- in order to
prevent repeatedly requesting a rebuild or a reshape on activation
Currently, loading an inactive table with rebuild/reshape flags
specified will cause dm-raid to rebuild/reshape on resume and thus start
updating the raid metadata (about the progress). When the second table
reload, to reset the flags, occurs the constructor accesses the volatile
progress state kept in the raid superblocks. Because the active mapping
is still processing the rebuild/reshape, that position will be stale by
the time the device is resumed.
In the reshape case, this causes data corruption by processing already
reshaped stripes again. In the rebuild case, it does _not_ cause data
corruption but instead involves superfluous rebuilds.
Fix by keeping the raid set frozen during the first resume and then
allow the rebuild/reshape during the second resume.
Fixes: 9dbd1aa3a ("dm raid: add reshaping support to the target")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 37a098e9d10db6e2efc05fe61e3a6ff2e9802c53 upstream.
The sloppy nature of lockless access to percpu pointers
(s->current_path) in rr_select_path(), from multiple threads, is
causing some paths to used more than others -- which results in less
IO performance being observed.
Revert these upstream commits to restore truly symmetric round-robin
IO submission in DM multipath:
b0b477c dm round robin: use percpu 'repeat_count' and 'current_path'
802934b dm round robin: do not use this_cpu_ptr() without having preemption disabled
There is no benefit to all this complexity if repeat_count = 1 (which is
the recommended default).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6085831883c25860264721df15f05bbded45e2a2 upstream.
Fixes: dfcfac3e4cd9 ("dm stats: collect and report histogram of IO latencies")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca763d0a53b264a650342cee206512bc92ac7050 upstream.
A rounding bug due to compiler generated temporary being 32bit was found
in remap_to_cache(). A localized cast in remap_to_cache() fixes the
corruption but this preferred fix (changing from uint32_t to sector_t)
eliminates potential for future rounding errors elsewhere.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30582c25a4b4e0a5e456a309fde79b845e9473b2 upstream.
Until now, the trans_stat information of passive devfreq is not updated.
This patch updates the trans_stat information after setting the target
frequency of passive devfreq device.
Fixes: 996133119f57 ("PM / devfreq: Add new passive governor")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcf23c79c4e46130701370af4383b61a3cba755c upstream.
The devfreq using passive governor is not able to change the governor.
So, the user can not change the governor through 'available_governor' sysfs
entry. Also, the devfreq which don't use the passive governor is not able to
change to 'passive' governor on the fly.
Fixes: 996133119f57 ("PM / devfreq: Add new passive governor")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc15ed663e7e53ee4dc3e60f8d09c93a0528c694 upstream.
On failure to return a pathname from ima_d_path(), a pointer to
dname is returned, which is subsequently used in the IMA measurement
list, the IMA audit records, and other audit logging. Saving the
pointer to dname for later use has the potential to race with rename.
Intead of returning a pointer to dname on failure, this patch returns
a pointer to a copy of the filename.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95e91b831f87ac8e1f8ed50c14d709089b4e01b8 upstream.
The issue is described here, with a nice testcase:
https://bugzilla.kernel.org/show_bug.cgi?id=192931
The problem is that shmat() calls do_mmap_pgoff() with MAP_FIXED, and
the address rounded down to 0. For the regular mmap case, the
protection mentioned above is that the kernel gets to generate the
address -- arch_get_unmapped_area() will always check for MAP_FIXED and
return that address. So by the time we do security_mmap_addr(0) things
get funky for shmat().
The testcase itself shows that while a regular user crashes, root will
not have a problem attaching a nil-page. There are two possible fixes
to this. The first, and which this patch does, is to simply allow root
to crash as well -- this is also regular mmap behavior, ie when hacking
up the testcase and adding mmap(... |MAP_FIXED). While this approach
is the safer option, the second alternative is to ignore SHM_RND if the
rounded address is 0, thus only having MAP_SHARED flags. This makes the
behavior of shmat() identical to the mmap() case. The downside of this
is obviously user visible, but does make sense in that it maintains
semantics after the round-down wrt 0 address and mmap.
Passes shm related ltp tests.
Link: http://lkml.kernel.org/r/1486050195-18629-1-git-send-email-dave@stgolabs.net
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reported-by: Gareth Evans <gareth.evans@contextis.co.uk>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 441398d378f29a5ad6d0fcda07918e54e4961800 upstream.
Currently SS_AUTODISARM is not supported in compatibility mode, but does
not return -EINVAL either. This makes dosemu built with -m32 on x86_64
to crash. Also the kernel's sigaltstack selftest fails if compiled with
-m32.
This patch adds the needed support.
Link: http://lkml.kernel.org/r/20170205101213.8163-2-stsp@list.ru
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Cc: Milosz Tanski <milosz@adfin.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Waiman Long <Waiman.Long@hpe.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Wang Xiaoqiang <wangxq10@lzu.edu.cn>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71ab6cfe88dcf9f6e6a65eb85cf2bda20a257682 upstream.
get_scan_count() considers the whole node LRU size when
- doing SCAN_FILE due to many page cache inactive pages
- calculating the number of pages to scan
In both cases this might lead to unexpected behavior especially on 32b
systems where we can expect lowmem memory pressure very often.
A large highmem zone can easily distort SCAN_FILE heuristic because
there might be only few file pages from the eligible zones on the node
lru and we would still enforce file lru scanning which can lead to
trashing while we could still scan anonymous pages.
The later use of lruvec_lru_size can be problematic as well. Especially
when there are not many pages from the eligible zones. We would have to
skip over many pages to find anything to reclaim but shrink_node_memcg
would only reduce the remaining number to scan by SWAP_CLUSTER_MAX at
maximum. Therefore we can end up going over a large LRU many times
without actually having chance to reclaim much if anything at all. The
closer we are out of memory on lowmem zone the worse the problem will
be.
Fix this by filtering out all the ineligible zones when calculating the
lru size for both paths and consider only sc->reclaim_idx zones.
The patch would need to be tweaked a bit to apply to 4.10 and older but
I will do that as soon as it hits the Linus tree in the next merge
window.
Link: http://lkml.kernel.org/r/20170117103702.28542-3-mhocko@kernel.org
Fixes: b2e18757f2c9 ("mm, vmscan: begin reclaiming pages on a per-node basis")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Trevor Cordes <trevor@tecnopolis.ca>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd538803731e50367b7c59ce4ad3454426a3d671 upstream.
lruvec_lru_size returns the full size of the LRU list while we sometimes
need a value reduced only to eligible zones (e.g. for lowmem requests).
inactive_list_is_low is one such user. Later patches will add more of
them. Add a new parameter to lruvec_lru_size and allow it filter out
zones which are not eligible for the given context.
Link: http://lkml.kernel.org/r/20170117103702.28542-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c57b5808c625f4fc93da330b932647eaff321f7 upstream.
With CONFIG_BALLOON_COMPACTION=y the kernel will mount balloon_mnt for
balloon page migration when we probe a virtio_balloon device. However
we do not unmount it when removing the device. Fix this.
Fixes: b1123ea6d3b3 ("mm: balloon: use general non-lru movable page feature")
Link: http://lkml.kernel.org/r/1486531318-35189-1-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd8416c47715cf324c9a16f13273f9fda87acfed upstream.
With rw_page, page_endio is used for completing IO on a page and it
propagates write error to the address space if the IO fails. The
problem is it accesses page->mapping directly which might be okay for
file-backed pages but it shouldn't for anonymous page. Otherwise, it
can corrupt one of field from anon_vma under us and system goes panic
randomly.
swap_writepage
bdev_writepage
ops->rw_page
I encountered the BUG during developing new zram feature and it was
really hard to figure it out because it made random crash, somtime
mmap_sem lockdep, sometime other places where places never related to
zram/zsmalloc, and not reproducible with some configuration.
When I consider how that bug is subtle and people do fast-swap test with
brd, it's worth to add stable mark, I think.
Fixes: dd6bd0d9c7db ("swap: use bdev_read_page() / bdev_write_page()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1587a4945408faa58d0485002c110eb2454740c upstream.
At the end of a window period, if the reclaimed pages is greater than
scanned, an unsigned underflow can result in a huge pressure value and
thus a critical event. Reclaimed pages is found to go higher than
scanned because of the addition of reclaimed slab pages to reclaimed in
shrink_node without a corresponding increment to scanned pages.
Minchan Kim mentioned that this can also happen in the case of a THP
page where the scanned is 1 and reclaimed could be 512.
Link: http://lkml.kernel.org/r/1486641577-11685-1-git-send-email-vinmenon@codeaurora.org
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Shiraz Hashim <shashim@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
