| Age | Commit message (Collapse) | Author |
|---|
|
If the driver needs to change a clock rate, then it must be propogated
through the MSTP clock to the parent clock (such as shdi0 -> sd0). Without
this we cannot up-rate default clocks which are really slow (such as the
mmcif1 which defaults to 12MHz where it could be running at 97MHz)
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The clock generator for rcar-gen2 has the lb, sdh, sd0 and sd1 clocks
parented to pll1_div2 where the hardware diagram shows these to be
directly fed from pll1.
This fixes the initial rate for sdh0 clock to be 97.5MHz instead of
the reported 48MHz where the manual says the default register values
are for 97.5MHz.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This restores the default clocks registration order as parsed from
devicetree, i.e. as before commit 1771b10d605d26ccee771a7fb4b08718
"clk: respect the clock dependencies in of_clk_init", for when there
is no explicit parent clock dependencies between clock providers
specified in the device tree.
It prevents regressions (boot failure, division by 0 errors) on
imx and exynos platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The orignal code will use the bigger rate between
"previous rate" and "current rate" when caculate the
rate.
In fact, hardware cares about the closest one.
So choose the closer rate between "previous rate" and
"current rate".
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The formula is numerator/denominator = Fin / (Fout * factor)
So
Fout = Fin * denominator / (numerator * factor).
Current clk_factor_round_rate and clk_factor_recalc_rate use
wrong formula. This patch will fix them.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The code has typo when calculate denominator. It should use
den_mask instead of num_mask.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch supports the A9-mux clocks used by ClockGenA9
A9-mux clock : Multiplexer inside ClockGenA9. A9 clock can be driven by
either PLL or External clock (with an optional divide-by-2). This is
implemented as 3-parent clock : PLL, Ext-clk OR Ext-clk/2
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch added support for DT registration of ClockGenA9/DDR/GPU
ClockgenA9/DDR : It includes c32 type PLL (also in ClockgenA1x), hence
only CLK_OF_DECLARE implementation is required.
ClockgenGPU : It includes c65 type PLL (also in ClockgenAx), hence
only CLK_OF_DECLARE implementation is required.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch supports the 216/432/660 type Quad Frequency Synthesizers
used by ClockGenB/C/D/E/F
QUADFS clock : It includes support for all 216/432/660 type Quad
Frequency Synthesizers : implemented as Fixed Parent / Rate / Gate clock,
with clock rate calculated reading H/w settings done at BOOT.
QuadFS have 4 outputs : chan0 chan1 chan2 chan3
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch supports the VCC-mux and MUX clocks used by ClockGenC/F
VCC-mux clock : Divider-Multiplexer-Gate inside ClockGenC/F
It includes support for each channel : 4-parent Multiplexer, Post Divide
by 1, 2, 4 or 8, Gate to switch OFF the output channel. The clock is
implemented using generic clocks implemented in the kernel clk_divider, clk_mux,
clk_gate and clk_composite (to combine all)
MUX clock : 2-parent clock used inside ClockGenC/F. The clock is implemented
using generic clocks implemented in the kernel clk_mux.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch supports the c65/c32 type PLLs used by ClockGenA(s)
PLL clock : It includes support for all c65/c32 type PLLs
inside ClockGenA(s) : implemented as Fixed Parent / Fixed Rate clock,
with clock rate calculated reading H/w settings done at BOOT.
c65 PLLs have 2 outputs : HS and LS
c32 PLLs have 1-4 outputs : ODFx
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch supports the DIVMUX and PreDiv clocks used by ClockGenA(s)
DIVMUX clock : Divider-Multiplexer-Gate inside ClockGenA(s)
It includes support for each channel : 3-parent Multiplexer,
Divider for each Parent, Gate to switch OFF the output channel. The
clock is implemented using generic clocks implemented in the kernel
clk_divider and clk_mux.
PreDiv clock : Fixed Divider Clock used inside ClockGenA(s) to divide
the oscillator clock by factor-of-16. The clock is implemented using
generic clocks implemented in the kernel clk_divider.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a new clk_ops->debug_init method to allow a clock hardware
driver to populate the clock's debugfs directory with entries
beyond those common for every clock.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
of_find_node_by_name() walks over all nodes and can thus walk outside of
the parent node. Use of_get_child_by_name() instead.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
If parent device does not have of_node set the s2mps11_clk_parse_dt()
returned NULL. This NULL was later passed to of_clk_add_provider() which
dereferenced it in pr_debug() call.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
drivers/clk/hisilicon/clk-hi3620.c:338
mmc_clk_delay() warn: always true condition '(para >= 0) => (0-u32max >= 0)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
If a rate change failed it's the opportunity of the caller to handle
this. Do not spam the log with a message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Framework is not ARM specific and used by many architectures. Change ML
from LAKML to LKML.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Until now the clock providers were initialized in the order found in
the device tree. This led to have the dependencies between the clocks
not respected: children clocks could be initialized before their
parent clocks.
Instead of forcing each platform to manage its own initialization order,
this patch adds this work inside the framework itself.
Using the data of the device tree the of_clk_init function now delayed
the initialization of a clock provider if its parent provider was not
ready yet.
The strict dependency check (all parents of a given clk must be
initialized) was added by Boris BREZILLON
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The clock bindings for Freescale CoreNet platform are updated.
So, the driver needs to be updated accordingly.
The main changes include:
- Added a new node to present the input system clock
- Changed PLL and MUX's compatible string
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The PCKRDY bit is not set until the system clock is enabled.
This patch moves the management of the ready status in the system clock
driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
System clks are just gates, and thus do not provide any rate operations.
Authorize clk rate change to be propagated to system clk parents.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Implement the determine_rate callback to choose the best parent clk that
fulfills the requested rate.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Briefly document the common clock framework locking scheme from a clock
driver point of view.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into clk-next-hisilcon
updating clock drivers for Hisilicon
|
|
This should read MOD0 and not MMC; MMC is just one example of a MOD0
clock.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Some divisor calculations were misrounded, causing higher than requested
rates on some clocks. Fix them up using DIV_ROUND_UP, and replace one
homebrew instance of it as well with the right macro.
Reported-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Allwinner actually reworked the PLL4 on A20; now it's compatible with
the sun4i PLL5/6 design previous to any divisions, as well as to the new
PLL8 in sun7i.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
into clk-next-sunxi
Allwinner sunXi SoCs clock changes
This adds support for the new, more correct clock node naming and gets
the A10 compatibles in line with the rest of the other SoCs. It also
adds support for the USB, GMAC and A31's PLL6 clocks. Some of these
changes also require DT modifications that will be merged via arm-soc.
|
|
Remove the static variable. So these common clock register helper could
be used in more SoCs.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
|
|
Now only fixed rate clocks are appended into the clock driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
|
|
The fixed rate and fixed factor clock isn't registered to clk table.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
|
|
WARNING: drivers/clk/socfpga/built-in.o(.data+0xc0): Section mismatch in
reference from the variable socfpga_child_clocks to the function
.init.text:socfpga_pll_init()
The variable socfpga_child_clocks references
the function __init socfpga_pll_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/clk/socfpga/built-in.o(.data+0x184): Section mismatch in
reference from the variable socfpga_child_clocks to the function
.init.text:socfpga_periph_init()
The variable socfpga_child_clocks references
the function __init socfpga_periph_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/clk/socfpga/built-in.o(.data+0x248): Section mismatch in
reference from the variable socfpga_child_clocks to the function
.init.text:socfpga_gate_init()
The variable socfpga_child_clocks references
the function __init socfpga_gate_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Reported-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
clk-next-mvebu
clock: mvebu new SoC changes for v3.15 (incremental pull #2)
- mvebu (Armada 375)
- fix ratio register offest
- mvebu (Armada 380)
- expand core divider clock driver to support 380 SoC (enables nand support)
|
|
Since clock operation within S2MPS11 and S5M8767 are similar, we can
support both the devices within a single driver.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The clocks in S2MPS11 and S5M8767 are managed in the same way, baring
a difference in the register offset. It would be better to update
existing S2MPS11 driver to support the clocks in S5M8767, rather than
creating an almost duplicate driver altogether.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
MOXA ART SoCs allow to determine PLL output and APB frequencies
by reading registers holding multiplier and divisor information.
Add a clock driver for this SoC.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The Core Divider clock support two new compatible strings for Armada
375 and Armada 380 SoCs. Add the compatible strings to the documentation.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-7-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit adds support for the Core Divider clocks of the Armada
380 SoCs. Similarly to Armada 370 and XP, the Core Divider clocks of
the 380 have gate capabilities. The only difference is the register layout.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-2-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit fixes the ratio register offset which is 0x4,
as per the Armada 375 SoC specification.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394638901-13368-2-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
ti/clk-divider.c does not calculate the rates consistently at the moment.
As an example, on OMAP3 we have a clock divider with a source clock of
864000000 Hz. With dividers 6, 7 and 8 the theoretical rates are:
6: 144000000
7: 123428571.428571...
8: 108000000
Calling clk_round_rate() with the rate in the first column will give the
rate in the second column:
144000000 -> 144000000
143999999 -> 123428571
123428572 -> 123428571
123428571 -> 108000000
Note how clk_round_rate() returns 123428571 for rates from 123428572 to
143999999, which is mathematically correct, but when clk_round_rate() is
called with 123428571, the returned value is surprisingly 108000000.
This means that the following code works a bit oddly:
rate = clk_round_rate(clk, 123428572);
clk_set_rate(clk, rate);
As clk_set_rate() also does clock rate rounding, the result is that the
clock is set to the rate of 108000000, not 123428571 returned by the
clk_round_rate.
This patch changes the ti/clk-divider.c to use DIV_ROUND_UP when
calculating the rate. This gives the following behavior which fixes the
inconsistency:
144000000 -> 144000000
143999999 -> 123428572
123428572 -> 123428572
123428571 -> 108000000
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
