| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI changes from Ingo Molnar:
"The main changes in this cycle were:
- further EFI code generalization to make it more workable for ARM64
- various extensions, such as 64-bit framebuffer address support,
UEFI v2.5 EFI_PROPERTIES_TABLE support
- code modularization simplifications and cleanups
- new debugging parameters
- various fixes and smaller additions"
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
efi: Fix warning of int-to-pointer-cast on x86 32-bit builds
efi: Use correct type for struct efi_memory_map::phys_map
x86/efi: Fix kernel panic when CONFIG_DEBUG_VIRTUAL is enabled
efi: Add "efi_fake_mem" boot option
x86/efi: Rename print_efi_memmap() to efi_print_memmap()
efi: Auto-load the efi-pstore module
efi: Introduce EFI_NX_PE_DATA bit and set it from properties table
efi: Add support for UEFIv2.5 Properties table
efi: Add EFI_MEMORY_MORE_RELIABLE support to efi_md_typeattr_format()
efifb: Add support for 64-bit frame buffer addresses
efi/arm64: Clean up efi_get_fdt_params() interface
arm64: Use core efi=debug instead of uefi_debug command line parameter
efi/x86: Move efi=debug option parsing to core
drivers/firmware: Make efi/esrt.c driver explicitly non-modular
efi: Use the generic efi.memmap instead of 'memmap'
acpi/apei: Use appropriate pgprot_t to map GHES memory
arm64, acpi/apei: Implement arch_apei_get_mem_attributes()
arm64/mm: Add PROT_DEVICE_nGnRnE and PROT_NORMAL_WT
acpi, x86: Implement arch_apei_get_mem_attributes()
efi, x86: Rearrange efi_mem_attributes()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull wchan kernel address hiding from Ingo Molnar:
"This fixes a wchan related information leak in /proc/PID/stat.
There's a bit of an ABI twist to it: instead of setting the wchan
field to 0 (which is our usual technique) we set it conditionally to a
0/1 flag to keep ABI compatibility with older procps versions that
only fetches /proc/PID/wchan (symbolic names) if the absolute wchan
address is nonzero"
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/proc, core/debug: Don't expose absolute kernel addresses via wchan
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timer departement provides:
- More y2038 work in the area of ntp and pps.
- Optimization of posix cpu timers
- New time related selftests
- Some new clocksource drivers
- The usual pile of fixes, cleanups and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
timeconst: Update path in comment
timers/x86/hpet: Type adjustments
clocksource/drivers/armada-370-xp: Implement ARM delay timer
clocksource/drivers/tango_xtal: Add new timer for Tango SoCs
clocksource/drivers/imx: Allow timer irq affinity change
clocksource/drivers/exynos_mct: Use container_of() instead of this_cpu_ptr()
clocksource/drivers/h8300_*: Remove unneeded memset()s
clocksource/drivers/sh_cmt: Remove unneeded memset() in sh_cmt_setup()
clocksource/drivers/em_sti: Remove unneeded memset()s
clocksource/drivers/mediatek: Use GPT as sched clock source
clockevents/drivers/mtk: Fix spurious interrupt leading to crash
posix_cpu_timer: Reduce unnecessary sighand lock contention
posix_cpu_timer: Convert cputimer->running to bool
posix_cpu_timer: Check thread timers only when there are active thread timers
posix_cpu_timer: Optimize fastpath_timer_check()
timers, kselftest: Add 'adjtick' test to validate adjtimex() tick adjustments
timers: Use __fls in apply_slack()
clocksource: Remove return statement from void functions
net: sfc: avoid using timespec
ntp/pps: use y2038 safe types in pps_event_time
...
|
|
Pull ARM updates from Russell King:
"In this ARM merge, we remove more lines than we add. Changes include:
- Enable imprecise aborts early, so that bus errors aren't masked
until later in the boot. This has the side effect that boot
loaders which provoke these aborts can cause the kernel to crash
early in boot, so we install a handler to report this event around
the site where these are enabled.
- Remove the buggy but impossible to enable cmpxchg syscall code.
- Add unwinding annotations to some assembly code.
- Add support for atomic half-word exchange for ARMv6k+.
- Reduce ioremap() alignment for SMP/LPAE cases where we don't need
the large alignment.
- Addition of an "optimal" 3G configuration for systems with 1G of
RAM.
- Increase vmalloc space by 128M.
- Constify some SMP operations structures, which have never been
writable.
- Improve ARMs dma_mmap() support for mapping DMA coherent mappings
into userspace.
- Fix to the NMI backtrace code in the IPI case on ARM where the
failing CPU gets stuck for 10s waiting for its own IPI to be
delivered.
- Removal of legacy PM support from the AMBA bus driver.
- Another fix for the previous fix of vdsomunge"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (23 commits)
ARM: 8449/1: fix bug in vdsomunge swab32 macro
arm: add missing of_node_put
ARM: 8447/1: catch pending imprecise abort on unmask
ARM: 8446/1: amba: Remove unused callbacks for legacy system PM
ARM: 8443/1: Adding support for atomic half word exchange
ARM: clean up TWD after previous patch
ARM: 8441/2: twd: Don't set CLOCK_EVT_FEAT_C3STOP unconditionally
ARM: 8440/1: remove obsolete documentation
ARM: make highpte an expert option
ARM: 8433/1: add a VMSPLIT_3G_OPT config option
ARM: 8439/1: Fix backtrace generation when IPI is masked
ARM: 8428/1: kgdb: Fix registers on sleeping tasks
ARM: 8427/1: dma-mapping: add support for offset parameter in dma_mmap()
ARM: 8426/1: dma-mapping: add missing range check in dma_mmap()
ARM: remove user cmpxchg syscall
ARM: 8438/1: Add unwinding to __clear_user_std()
ARM: 8436/1: hw_breakpoint: remove unnecessary header
ARM: 8434/2: Revert "7655/1: smp_twd: make twd_local_timer_of_register() no-op for nosmp"
ARM: 8432/1: move VMALLOC_END from 0xff000000 to 0xff800000
ARM: 8430/1: use default ioremap alignment for SMP or LPAE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Support for new MM features in ARCv2 cores (THP, PAE40) Some generic
THP bits are touched - all ACKed by Kirill
- Platform framework updates to prepare for EZChip arrival (still in works)
- ARC Public Mailing list setup finally (linux-snps-arc@lists.infraded.org)
* tag 'arc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (42 commits)
ARC: mm: PAE40 support
ARC: mm: PAE40: tlbex.S: Explicitify the size of pte_t
ARC: mm: PAE40: switch to using phys_addr_t for physical addresses
ARC: mm: HIGHMEM: populate high memory from DT
ARC: mm: HIGHMEM: kmap API implementation
ARC: mm: preps ahead of HIGHMEM support #2
ARC: mm: preps ahead of HIGHMEM support
ARC: mm: use generic macros _BITUL()/_AC()
ARC: mm: Improve Duplicate PD Fault handler
MAINTAINERS: Add public mailing list for ARC
ARC: Ensure DT mem base is same as what kernel is built with
ARC: boot: Non Master cpus only need to call EARLY_CPU_SETUP once
ARCv2: smp: [plat-*]: No need to explicitly call mcip_init_smp()
ARC: smp: Introduce smp hook @init_irq_cpu called for all cores
ARC: smp: Rename platform hook @init_smp -> @init_cpu_smp
ARCv2: smp: [plat-*]: No need to explicitly call mcip_init_early_smp()
ARC: smp: Introduce smp hook @init_early_smp for Master core
ARC: remove @init_time, @init_irq platform callbacks
ARC: smp: irqchip: handle IPI as percpu irq like timer
ARC: boot: Support Halt-on-reset and Run-on-reset SMP booting modes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS changes from Jesper Nilsson:
"Mostly another batch of code removal due to move to standard
frameworks for CRISv32, initial devicetree configuration for a couple
of boards, and some small fixes for kgdb and time handling"
* tag 'cris-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: Drop reference to get_cmos_time()
CRIS: Drop code related to obsolete or unused kconfigs
cris: time: Cleanup of persistent clock stuff
cris: re-use helpers to dump data in hex format
CRIS v32: remove old GPIO and LEDs code
CRIS v32: remove I2C bitbanging driver
CRIS v32: add ARTPEC-3 and P1343 device trees
CRIS v32: dev88: add GPIO, LEDs, RTC, temp sensor
CRIS: add dt-bindings symlink
CRIS v32: increase NR_IRQS
cris: arch-v10: kgdb: Add '__used' for static variable is_dyn_brkp
cris: arch-v10: kgdb: Use BAR instead of DTP0 for register P12
cris: kgdb: use native hex2bin
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull avr32 update from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: atngw100: remove useless include
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/sun3: Use %pM format specifier to print ethernet address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Move the out-of-LED-tree led-sead3 driver to the LED subsystem.
- Add 'invert' sysfs attribute to the heartbeat trigger.
- Add Device Tree support to the leds-netxbig driver and add related DT
nodes to the kirkwood-netxbig.dtsi and kirkwood-net5big.dts files.
Remove static LED setup from the related board files.
- Remove redundant brightness conversion operation from leds-netxbig.
- Improve leds-bcm6328 driver: improve default-state handling, add more
init configuration options, print invalid LED instead of warning only
about maximum LED value.
- Add a shutdown function for setting gpio-leds into off state when
shutting down.
- Fix DT flash timeout property naming in leds-aat1290.txt.
- Switch to using devm prefixed version of led_classdev_register()
(leds-cobalt-qube, leds-hp6xx, leds-ot200, leds-ipaq-micro,
leds-netxbig, leds-locomo, leds-menf21bmc, leds-net48xx, leds-wrap).
- Add missing of_node_put (leds-powernv, leds-bcm6358, leds-bcm6328,
leds-88pm860x).
- Coding style fixes and cleanups: led-class/led-core, leds-ipaq-micro.
* tag 'leds_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (27 commits)
leds: 88pm860x: add missing of_node_put
leds: bcm6328: add missing of_node_put
leds: bcm6358: add missing of_node_put
powerpc/powernv: add missing of_node_put
leds: leds-wrap.c: Use devm_led_classdev_register
leds: aat1290: Fix property naming of flash-timeout-us
leds: leds-net48xx: Use devm_led_classdev_register
leds: leds-menf21bmc.c: Use devm_led_class_register
leds: leds-locomo.c: Use devm_led_classdev_register
leds: leds-gpio: add shutdown function
Documentation: leds: update DT bindings for leds-bcm6328
leds-bcm6328: add more init configuration options
leds-bcm6328: simplify and improve default-state handling
leds-bcm6328: print invalid LED
leds: netxbig: set led_classdev max_brightness
leds: netxbig: convert to use the devm_ functions
ARM: mvebu: remove static LED setup for netxbig boards
ARM: Kirkwood: add LED DT entries for netxbig boards
leds: netxbig: add device tree binding
leds: triggers: add invert to heartbeat
...
|
|
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,r;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use of resource managed function devm_led_classdev_register to
make initialization path simpler. Also removed redundant remove
function.
Signed-off-by: Fida Mohammad <fmthoker@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
flash-timeout-us property name is changed to flash-max-timeout-us.
This patch fixes that name.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use devm_led_classdev_register instead of led_classdev_register,
removing the redundant net48xx_led_remove function.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register, consequently remove redundant
menf21bmc_led_remove function.
Also drop the unneeded label err_free_leds.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use resource managed function devm_led_classdev_register to make
initialisation path simpler.
Also removed redundant led_classdev_unregister function.
Signed-off-by: Fida Mohammad <fmthoker@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
add a shutdown function for setting the gpio-leds
into off state when shuting down.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch adds latest DT bindings for leds-bcm6328 init register
configuration.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch adds more init register configuration options:
- Serial LEDs multiplexing.
- Serial LEDs clock signal low/high polarity.
- Serial LEDs data signal low/high polarity.
- Serial LEDs shift direction inverted/normal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch simplifies and improves the code related to
default-state handling.
It also changes the code to power off the LEDs by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Print invalid LED instead of warning only about maximum LED value.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch sets the led_classdev max_brightness to the maximum level
value supported by hardware. This allows to get rid of the brightness
conversion operation (from software [0:LED_FULL] to hardware ranges) in
brightness_set().
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch converts the leds-netxbig driver to use the devres functions
devm_gpio_request_one() and devm_led_classdev_register(). This allows to
simplify the code a bit.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Since DT support is now available for the LEDs found on the LaCie
netxbig boards (Kirkwood-based), then the old-fashion netxbig board
setup file is no longer needed. This patch removes this file.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch adds DT entries for the LEDs found on the Kirkwood-based
LaCie boards 2Big and 5Big Network v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch adds device tree support for the netxbig LEDs.
This also introduces a additionnal DT binding for the GPIO extension bus
(netxbig-gpio-ext) used to configure the LEDs. Since this bus could also
be used to control other devices, then it seems more suitable to have it
in a separate DT binding.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch adds possibility to invert heartbeat blinking.
The inverted LED is more time ON then OFF. It's because it looks
better when the heartbeat LED is next to other LED which is most
time ON. The invert value is exported same way via sysfs in file
invert like oneshot. I get inspiration from this trigger.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Since the API for controlling LED brightness and blinking is defined in
the LED core, move the related timer and work callbacks to the led-core.c,
and initialize them through a new led_core_init API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
|
|
Fixes the following randconfig problem
leds-sead3.c:(.text+0x7dc): undefined reference to `led_classdev_unregister'
leds-sead3.c:(.text+0x7e8): undefined reference to `led_classdev_unregister'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Spaces at the starting of a line are removed, indentation using
tab, instead of space. Also, line width of more than 80 characters
is also taken care of.
Two warnings are left alone to aid better readability.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use of resource-managed function devm_led_classdev_register
instead of led_classdev_register is preferred, consequently
remove redundant function micro_leds_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to make the error path simpler.
The goto is replaced with direct return, unneeded label err is
dropped. Also, remove redundant ot200_led_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to simplify error path.
An unnecessary check of ret is replaced with a direct return
Also, remove redundant hp6xxled_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register to make the error-path simpler.
To be compatible with the change, goto is replaced with direct
return, unneeded label err_null is dropped and unnecessary variable
retval is removed. Also, remove redundant cobalt_qube_led_remove.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Quite a few new features for regmap this time, mostly expanding things
around the edges of the existing functionality to cover more devices
rather than thinsg with wide applicability:
- Support for offload of the update_bits() operation to hardware
where devices implement bit level access.
- Support for a few extra operations that need scratch buffers on
fast_io devices where we can't sleep.
- Expanded the feature set of regmap_irq to cope with some extra
register layouts.
- Cleanups to the debugfs code"
* tag 'regmap-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Allow installing custom reg_update_bits function
regmap: debugfs: simplify regmap_reg_ranges_read_file() slightly
regmap: debugfs: use memcpy instead of snprintf
regmap: debugfs: use snprintf return value in regmap_reg_ranges_read_file()
regmap: Add generic macro to define regmap_irq
regmap: debugfs: Remove scratch buffer for register length calculation
regmap: irq: add ack_invert flag for chips using cleared bits as ack
regmap: irq: add support for chips who have separate unmask registers
regmap: Allocate buffers with GFP_ATOMIC when fast_io == true
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for the v4.4 development cycle.
The only changes hitting outside drivers/gpio are in the pin control
subsystem and these seem to have settled nicely in linux-next.
Development mistakes and catfights are nicely documented in the
reverts as you can see. The outcome of the ABI fight is that we're
working on a chardev ABI for GPIO now, where hope to show results for
the v4.5 kernel.
Summary of changes:
GPIO core:
- Define and handle flags for open drain/open collector and open
source/open emitter, also know as "single-ended" configurations.
- Generic request/free operations that handle calling out to the
(optional) pin control backend.
- Some refactoring related to an ABI change that did not happen, yet
provide useful.
- Added a real-time compliance checklist. Many GPIO chips have
irqchips, and need to think this over with the RT patches going
upstream.
- Restructure, fix and clean up Kconfig menus a bit.
New drivers:
- New driver for AMD Promony.
- New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
ISA-style. Very retro.
Subdriver changes:
- OMAP changes to handle real time requirements.
- Handle trigger types for edge and level IRQs on PL061 properly. As
this hardware is very common it needs to set a proper example for
others to follow.
- Some container_of() cleanups.
- Delete the unused MSM driver in favor of the driver that is
embedded inside the pin control driver.
- Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
targets.
- A consolidated IT87xx driver replacing the earlier very specific
IT8761e driver.
- Handle the TI TCA9539 in the PCA953x driver. Also handle ACPI
devices in this subdriver.
- Drop xilinx arch dependencies as these FPGAs seem to profilate over
a few different architectures. MIPS and ARM come to mind"
* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
gpio: fix up SPI submenu
gpio: drop surplus I2C dependencies
gpio: drop surplus X86 dependencies
gpio: dt-bindings: document the official use of "ngpios"
gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
gpio / ACPI: Allow shared GPIO event to be read via operation region
gpio: group port-mapped I/O drivers in a menu
gpio: Add ACCES 104-IDIO-16 driver maintainer entry
gpio: zynq: Document interrupt-controller DT binding
gpio: xilinx: Drop architecture dependencies
gpio: generic: Revert to old error handling in bgpio_map
gpio: add a real time compliance notes
Revert "gpio: add a real time compliance checklist"
gpio: Add GPIO support for the ACCES 104-IDIO-16
gpio: driver for AMD Promontory
gpio: xlp: Convert to use gpiolib irqchip helpers
gpio: add a real time compliance checklist
gpio/xilinx: enable for MIPS
gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
gpiolib: Split GPIO flags parsing and GPIO configuration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.4 kernel
development cycle. Development pace is high in pin control again this
merge window. 28 contributors, 83 patches.
It hits a few sites outside the pin control subsystem:
- Device tree bindings in Documentation (as usual)
- MAINTAINERS
- drivers/base/* for the "init" state handling by Doug Anderson.
This has been ACKed by Greg.
- drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
in the USB subsystem. This has been ACKed by both Greg and Felipe.
- arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
through the ARM SoC tree but ended up here.
This time I am using Geert Uytterhoeven as submaintainer for SH PFC
since the are three-four people working in parallel with new Renesas
ASICs.
Summary of changes:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state different from
the "default" state for pin control state handling in the core
framework. This is applied before the driver's probe() call if
defined and takes precedence over "default". If both are defined,
"init" will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the device tree
ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r" controller.
- Moved the Cygnus driver to use DT-provided GPIO ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic fixes"
* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
pinctrl: pinconf: remove needless loop
pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
pinctrl: zynq: fix UTF-8 errors
pinctrl: zynq: Initialize early
pinctrl: at91: add missing of_node_put
pinctrl: tegra-xusb: Correct lane mux options
pinctrl: intel: Add Intel Broxton pin controller support
pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
drivers/pinctrl: Add the concept of an "init" state
pinctrl: uniphier: set input-enable before pin-muxing
pinctrl: cygnus: Add new compatible string for gpio controller driver
pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
pinctrl: cygnus: Optional DT property to support pin mappings
pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
...
|
|
Pull EDAC updates from Borislav Petkov:
"A bunch of fixes all over the place and some hw enablement this time.
- Convert EDAC to debugfs wrappers and make drivers use those
(Borislav Petkov)
- L3 and SoC support for xgene_edac (Loc Ho)
- AMD F15h, models 0x60-6f support to amd64_edac (Aravind
Gopalakrishnan)
- Fixes and cleanups all over the place"
* tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
EDAC: Fix PAGES_TO_MiB macro misuse
EDAC, altera: SoCFPGA EDAC should not look for ECC_CORR_EN
EDAC: Use edac_debugfs_remove_recursive()
EDAC, ppc4xx_edac: Fix module autoload for OF platform driver
Documentation/EDAC: Add reference documents section for amd64_edac
EDAC, amd64_edac: Update copyright and remove changelog
EDAC, amd64_edac: Extend scrub rate support to F15hM60h
EDAC: Don't allow empty DIMM labels
EDAC: Fix sysfs dimm_label store operation
EDAC: Fix sysfs dimm_label show operation
arm64, EDAC: Add L3/SoC DT subnodes to the APM X-Gene SoC EDAC node
EDAC, xgene: Add SoC support
EDAC, xgene: Fix possible sprintf() overflow issue
EDAC, xgene: Add L3 support
EDAC, Documentation: Update X-Gene EDAC binding for L3/SoC subnodes
EDAC, sb_edac: Fix TAD presence check for sbridge_mci_bind_devs()
EDAC, ghes_edac: Remove redundant memory_type array
EDAC, xgene: Convert to debugfs wrappers
EDAC, i5100: Convert to debugfs wrappers
EDAC, altera: Convert to debugfs wrappers
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
- Add new ioctl to allow userspace to send multi commands
- Wait for card busy signalling before starting SDIO requests
- Remove MMC_CLKGATE
- Enable tuning for DDR50 mode
- Some code clean-up/improvements to mmc pwrseq
- Use highest priority for eMMC restart handler
- Add DT bindings for eMMC hardware reset support
- Extend the mmc_send_tuning() API
- Improve ios show for debugfs
- A couple of code optimizations
MMC host:
- Some generic OF improvements
- Various code clean-ups
- sirf: Add support for DDR50
- sunxi: Add support for card busy detection
- mediatek: Use MMC_CAP_RUNTIME_RESUME
- mediatek: Add support for eMMC HW-reset
- mediatek: Add support for HS400
- dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
- dw_mmc: Add external DMA interface support
- dw_mmc: Some various improvements
- dw_mmc-rockchip: MMC tuning with the clock phase framework
- sdhci: Properly clear IRQs during resume
- sdhci: Enable tuning for DDR50 mode
- sdhci-of-esdhc: Use IRQ mode for card detection
- sdhci-of-esdhc: Support both BE and LE host controller
- sdhci-pci: Build o2micro support in the same module
- sdhci-pci: Support for new Intel host controllers
- sdhci-acpi: Support for new Intel host controllers"
* tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc: (73 commits)
mmc: dw_mmc: fix the wrong setting for UHS-DDR50 mode
mmc: dw_mmc: fix the CardThreshold boundary at CardThrCtl register
mmc: dw_mmc: NULL dereference in error message
mmc: pwrseq: Use highest priority for eMMC restart handler
mmc: mediatek: add HS400 support
mmc: mmc: extend the mmc_send_tuning()
mmc: mediatek: add implement of ops->hw_reset()
mmc: mediatek: fix got GPD checksum error interrupt when data transfer
mmc: mediatek: change the argument "ddr" to "timing"
mmc: mediatek: make cmd_ints_mask to const
mmc: dt-bindings: update Mediatek MMC bindings
mmc: core: Add DT bindings for eMMC hardware reset support
mmc: omap_hsmmc: Enable omap_hsmmc for Keystone 2
mmc: sdhci-acpi: Add more ACPI HIDs for Intel controllers
mmc: sdhci-pci: Add more PCI IDs for Intel controllers
arm: lpc18xx_defconfig: remove CONFIG_MMC_DW_IDMAC
arm: hisi_defconfig: remove CONFIG_MMC_DW_IDMAC
arm: exynos_defconfig: remove CONFIG_MMC_DW_IDMAC
arc: axs10x_defconfig: remove CONFIG_MMC_DW_IDMAC
mips: pistachio_defconfig: remove CONFIG_MMC_DW_IDMAC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver for MAX31790, added support for TMP75C, as well as cleanups
and minor improvements in various drivers"
* tag 'hwmon-for-linus-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (fam15h_power) Add max compute unit accumulated power
hwmon: (fam15h_power) Enable power1_input on AMD Carrizo
hwmon: (fam15h_power) Refactor attributes for dynamically added
hwmon: (ina2xx) remove no longer used variable 'kind'
hwmon: (nct6775) Introduce separate temperature labels for NCT6792 and NCT6793
hwmon: (nct6775) NCT6791D and NCT6792D have an additional temperature source
hwmon: (ina2xx) give precedence to DT over checking for platform data.
hwmon: (ina2xx) convert driver to using regmap
hwmon: (coretemp) Increase limit of maximum core ID from 32 to 128.
hwmon: (lm75) Add support for TMP75C
hwmon: (ibmpowernv) Add OF compatibility table entry
hwmon: (abx500) drop the use of IRQF_NO_SUSPEND
hwmon: (max31790) Fix dereference of ERR_PTR
hwmon: Driver for Maxim MAX31790
|
|
Function get_cmos_time() was removed with commit 657926a83df9 ("cris:
time: Cleanup of persistent clock stuff"). The remaining reference to
it may cause the following build error.
arch/cris/kernel/built-in.o:(___ksymtab+get_cmos_time+0x0):
undefined reference to `get_cmos_time'
Makefile:946: recipe for target 'vmlinux' failed
Fixes: 657926a83df9 ("cris: time: Cleanup of persistent clock stuff")
Cc: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
|
|
Drop all code related to Kconfigs that don't exist.
Fix one Kconfig where it was actually typo:ed (ETRAX_KGB_PORT2)
Drop content related to CRIS v32 SoCs from etraxgpio.h headerfile,
all use of GPIO for both ETRAX FS and ARTPEC-3 should now be through
standard gpiolib instead.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
- Remove update_persistent_clock(), as it does nothing now.
- Remove read_persistent_clock(), let it fall back to the weak version.
Cc: Mikael Starvik <starvik@axis.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
|
|
There are native helpers such as print_hex_byte() and %*ph specifier to dump
data in hex format. Re-use them instead of a custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
|
|
Since we now have a gpiolib driver, remove this code:
The gpio-etraxfs driver (along with things like gpio-keys-polled for
polling support) replaces the GIO driver implementations in mach-a3 and
mach-fs. The various generic external chip drivers replace the "virtual
gpio" parts.
The generic gpio-leds driver replaces the LED handling.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
|
|
Now that we have a gpiolib GPIO driver, the generic i2c-gpio driver
provides this functionality.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
|
