Age | Commit message (Collapse) | Author |
|
Add pmic / regulator nodes to Mele M9 dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The blue led on the Mele M9 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to m9:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using
the same dts for both models. Unfortunately this does not work for the otg
controller, on the M9 this is routed to a micro-usb connector on the outside,
while as on the A1000G-quad it is connected to an usb to sata bridge
(which is not populated on the M9 pcb).
This commit adds a new dts for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Prepare the device trees to use the C preprocessor.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Mele M9 has an ir receiver, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Mele M9 has an ethernet board, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Mele M9 / A1000G quad has a blue status led, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Mele M9 / A1000G quad uses both usb-ports, one goes to an internal
usb wifi card, the other to a build-in usb-hub, so neither need their
OHCI companion controller to be enabled since the are always connected at
USB-2 speeds.
The controller which is attached to the wifi also does not need a vbus
regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a new sun6i-a31-m9 dts file for the Mele M9 / Mele A1000G Quad. These
HTPCs use the same board in a different case, for more details see:
http://linux-sunxi.org/Mele_M9
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|