| Age | Commit message (Collapse) | Author |
|---|
|
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable REGULATOR_FIXED_VOLTAGE for all OMAP2+ platforms
otherwise system can't boot from SD-card when kernel is
built for single SoC (for example, with CONFIG_SOC_DRA7XX=y only).
It's also required for almost all TI SoC's platforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
|
|
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we have a 32k clocksource driver, let's
select it for OMAP2PLUS builds.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Move the code out from arch/arm/common and merge it inside of the dmaengine
driver.
This change is done with as minimal (if eny) functional change to the code
as possible to avoid introducing regression.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
OMAP5 SoC has Cortex-A15 which does not use TWD timer. It uses
ARCH_TIMER instead, clean up unwanted configuration and enable
OMAP_INTERCONNECT and OPP which is necessary for expected functionality
on the SoC.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DRA7 does use OPP, uses OMAP interconnect and also does require SCU.
These are missing in the SoC only build of DRA7 breaking various PM
features in DRA7 only build.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM development updates from Russell King:
"Included in this update:
- moving PSCI code from ARM64/ARM to drivers/
- removal of some architecture internals from global kernel view
- addition of software based "privileged no access" support using the
old domains register to turn off the ability for kernel
loads/stores to access userspace. Only the proper accessors will
be usable.
- addition of early fixup support for early console
- re-addition (and reimplementation) of OMAP special interconnect
barrier
- removal of finish_arch_switch()
- only expose cpuX/online in sysfs if hotpluggable
- a number of code cleanups"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits)
ARM: software-based priviledged-no-access support
ARM: entry: provide uaccess assembly macro hooks
ARM: entry: get rid of multiple macro definitions
ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die()
ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore()
ARM: mm: improve do_ldrd_abort macro
ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit()
ARM: entry: efficiency cleanups
ARM: entry: get rid of asm_trace_hardirqs_on_cond
ARM: uaccess: simplify user access assembly
ARM: domains: remove DOMAIN_TABLE
ARM: domains: keep vectors in separate domain
ARM: domains: get rid of manager mode for user domain
ARM: domains: move initial domain setting value to asm/domains.h
ARM: domains: provide domain_mask()
ARM: domains: switch to keeping domain value in register
ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE
ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD()
ARM: 8416/1: Feroceon: use of_iomap() to map register base
ARM: 8415/1: early fixmap support for earlycon
...
|
|
* fixes: (28 commits)
ARM: ux500: add an SMP enablement type and move cpu nodes
ARM: dts: keystone: fix dt bindings to use post div register for mainpll
ARM: nomadik: disable UART0 on Nomadik boards
ARM: dts: i.MX35: Fix can support.
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: DRA7: hwmod: fix gpmc hwmod
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
...
|
|
Restore the OMAP4 barrier behaviour using the new implementation which
allows multiplatform systems to hook into the mb() and wmb() ARM
implementations to perform any necessary additional barrier maintanence.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit 606da4826b89b044b51e3a84958b802204cfe4c7.
We actually need this code for proper behaviour of OMAP4, and it needs
fixing a different way other than just removing the code. Disabling
code which is necessary in the hopes of persuing multiplatform kernels
is a stupid approach.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP
system, however AM43XX needs this option regardless of CONFIG_SMP and also
for an AM43XX only build as it is important for controlling power in the SoC.
Without this we cannot suspend the CPU for SoC suspend or cpuidle. The
ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order
for the PRCM to transition the MPU to low power modes.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Olof Johansson:
"We were expecting to sit on this branch through most of the merge
window since the contents was merged into our tree late, but we ended
up sitting on all of our contents so it can go in with the rest.
The contents here is:
- a large branch of cleanups of the CM/PRM blocks on OMAP.
- a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- a branch with DT updates for Freescale i.MX. including some
shuffling from .dts to .dtsi (include) files that causes a little
churn"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/late
Merge "urgent omap boot fix for v4.1 if MFD_SYSCON is not set" from Tony
Lindgren:
Urgent pull request for v4.1 to booting for custom kernel
.config files that do not have MFD_SYSCON set.
Omaps now have a dependency to MFD_SYSCON for system control
module generic register area and some clocks with the changes
done in omap-for-v4.1/prcm-dts branch.
This can be pulled on top of omap-for-v4.1/prcm-dts, or into
fixes for v4.1.
We already do have a slight MFD_SYSCON dependency for
REGULATOR_PBIAS for dual voltage MMC cards on the first MMC
bus for many devices, so from that point of view this can
also be merged separately from omap-for-v4.1/prcm-dts.
* tag 'omap-for-v4.1/prcm-dts-mfd-syscon-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With the recent changes omaps have developed a dependency to MFD_SYSCON.
This is used for system control module generic register area and some
clocks.
We do have it selected in omap2plus_defconfig, but targeted config
files may not have it selected. Let's make sure it's selected like
few other ARM platforms are already doing.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ARM errata 798181 is applicable for OMAP5/DRA7 based devices. So enable
the same in the build.
DRA7xx is based on Cortex-A15 r2p2 revision.
ARM Errata extract and workaround information is as below.
On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
adequately shooting down all use of the old entries. The
ARM_ERRATA_798181 option enables the Linux kernel workaround
for this erratum which sends an IPI to the CPUs that are running
the same ASID as the one being invalidated.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Cc: Gregoire Gentil <gregoire@gentil.com>
Cc: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
http://www.embest-tech.com/product/single-board-computers/index.html
Cc: Thomas Weber <thomas@tomweber.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Also looks like this board is no longer listed on ema-tech.com
product page at:
http://ema-tech.com/en/categories.html
Cc: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Kconfig-Option OMAP4_ERRATA_I688 is never visible due to a
contradiction in it's dependencies.
The option requires ARCH_MULTIPLATFORM to be 'disabled'. However, an
enclosing menu requires either ARCH_MULTI_V6 or ARCH_MULTI_V7 to be
enabled. These options inherit a dependency from an enclosing menu,
that requires ARCH_MULTIPLATFORM to be 'enabled'.
This is a contradiction and made this option also unavailable for
non-multiplatform configurations.
Since there are no selects on OMAP4_ERRATA_I688, which would ignore
dependencies, the code related to that option is dead and can be
removed.
This (logical) defect has been found with the undertaker tool.
(https://undertaker.cs.fau.de)
Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We still have SND_OMAP_SOC_AM3517EVM depending on MACH_OMAP3517EVM,
so let's keep MACH_OMAP3517EVM Kconfig option around for a little
bit longer.
This removes the dependency between ARM SoC changes and the ASoC
changes, and allows the following three options for the driver:
1. Update the driver for device tree based booting
2. Initialize the driver with legacy platform data, then update
the driver for device tree based booting
3. Just remove the driver if there are no audio users for
3517-evm board
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This board is working with device tree based booting so there should
not be any need to keep the legacy booting support around. People
using this board can boot it with appended DTB with existing bootloader.
By removing the 3517 legacy booting support we can get a bit closer to
making all of omap3 boot in device tree only mode.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This board is working with device tree based booting so there should
not be any need to keep the legacy booting support around. People
using this board can boot it with appended DTB with existing bootloader.
By removing the 3517 legacy booting support we can get a bit closer to
making all of omap3 boot in device tree only mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This board is working with device tree based booting so there should
not be any need to keep the legacy booting support around. People
using this board can boot it with appended DTB with existing bootloader.
By removing the 3517 legacy booting support we can get a bit closer to
making all of omap3 boot in device tree only mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/omap-gpmc
Pull "move omap gpmc to drivers finally" from Tony Lindgren:
We can finally move the GPMC code to live in drivers/memory for
further clean up work.
Note that we still have dependencies to the legacy booting for
omap3 board-*.c files for setting up the board specific memory
timings. For that we need the timing related things still exposed
in include/linux/omap-gpmc.h. This will all become private data
to the GPMC driver once the legacy booting support can be dropped.
* tag 'omap-for-v3.19/gpmc-move-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Just move to drivers as further clean-up can now happen there
finally.
Let's also add Roger and me to the MAINTAINERS so we get
notified for any patches related to GPMC.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Removing minimal support for etb/etm to favour an implementation
that is more flexible, extensible and capable of handling more
platforms.
Also removing the only client of the old driver. That code can
easily be replaced by entries for etb/etm in the device tree.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This board seems to be in use only for few automated
boot test system and has been booting in device tree
only mode for quite some time now.
So let's drop the board file for it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The 81xx support is known to be broken for quite some
time now because of missing patches. And it should be
using device tree based booting now anyways.
So let's just drop the board file for it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support. Among the things new for this release
are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier
SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still
ongoing"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits)
ARM: hisi: depend on ARCH_MULTI_V7
CNS3xxx: Fix debug UART.
ARM: at91: fix nommu build regression
ARM: meson: add basic support for MesonX SoCs
ARM: meson: debug: add debug UART for earlyprintk support
irq: Export handle_fasteoi_irq
ARM: mediatek: Add earlyprintk support for mt6589
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
ARM: debug: fix alphanumerical order on debug uarts
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
...
|
|
Just move the code over as it has no dependencies
on arch/arm/ anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 21278aeafbfa ("ARM: use menuconfig for sub-arch menus") improved
the sub-arch menus, but accidentally caused new warnings for omap1.
This was because the commit added a menu entry around config ARCH_OMAP
bool entry where the menu had depends on ARCH_MULTI_V6 || ARCH_MULTI_V7.
As ARCH_OMAP is shared between omap1 and omap2plus, let's fix the
issue by defining ARCH_OMAP in the shared plat-omap/Kconfig.
Fixes: 21278aeafbfa ("ARM: use menuconfig for sub-arch menus")
Reported-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
OPP is now a normal kernel library selected by its users rather than a
feature that architectures need to enable so ARCH_HAS_OPP serves no
function any more - remove the selects.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull ARM fixes from Russell King:
"A number of low impact fixes, the most noticable one is the thumb2
frame pointer fix. We also fix a regression caused during this merge
window with ARM925 CPUs running with caches disabled, and fix a number
of warnings"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: arm925: ensure assembly sets up writethrough mapping
ARM: perf: fix compiler warning with gcc 4.6.4 (and tidy code)
ARM: l2c: fix dependencies on PL310 errata symbols
ARM: 8069/1: Make thread_save_fp macro aware of THUMB2 mode
ARM: 8068/1: scoop: Remove unused variable
|
|
A number of configurations spit out warnings similar to:
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_588369 which has unmet direct dependencies (CACHE_L2X0)
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_727915 which has unmet direct dependencies (CACHE_L2X0)
Clean up the dependencies here:
* PL310 symbols should only be selected when CACHE_L2X0 is enabled.
* Since the cache-l2x0 code detects PL310 presence at runtime, and we will
eventually get rid of CACHE_PL310, surround these errata options with an
if CACHE_L2X0 conditional rather than repeating the dependency against
each.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The System Type menu is getting quite long with platforms and is
inconsistent in handling of sub-arch specific options. Tidy up the menu
by making platform options a menuconfig entry containing any platform
specific config items.
[arnd: change OMAP part according to suggestion from
Tony Lindgren <tony@atomide.com>]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This config exists entirely to hide the cpufreq menu from the
kernel configuration unless a platform has selected it. Nothing
is actually built if this config is 'Y' and it just leads to more
patches that add a select under a platform Kconfig so that some
other CPUfreq option can be chosen. Let's remove the option so
that we can always enable CPUfreq drivers on ARM platforms.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit d941f86fad41b ("ARM: l2c: AM43x: add L2 cache support") enabled
the L2 cache support for the am43xx SoC, but caused a build regression
when the driver for that cache controller is disabled:
arch/arm/mach-omap2/built-in.o: In function `am43xx_init_early':
:(.init.text+0xb20): undefined reference to `omap_l2_cache_init'
This did not happen for OMAP4, which has the same call, but enables
the l2x0 driver unconditionally. We could do the same thing for
am43xx, but it seems better to allow turning it off and make the
code work in either case.
This adds an inline wrapper for omap_l2_cache_init for the disabled
case, and removes the 'select' from OMAP4 so it becomes a user
visible option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
|
