| Age | Commit message (Collapse) | Author |
|---|
|
When building for multi-omap, and OMAP4 is enabled, CONFIG_ARCH_OMAP4
will be true and prevent included code from building/running for
OMAP2/3 as well.
This problem exists in io.c where some hwmod/PM/SDRC init code is
prevented from running even on OMAP2/3 when OMAP4 is included in a
multi-OMAP build.
A quick glance suggests that this #ifndef is no longer needed in most
of the cases. In the remaining cases, the function is wrapped with
"if (cpu_is_omap24xx() || cpu_is_omap34xx())" which will be optimized
out for OMAP4-only builds.
Note that this is only a short-term fix. Longer-term, OMAP4
needs to create init functions for SDRC and hwmod late-init.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Get rid of the following warnings:
warning: non-ANSI function declaration of function [...]
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Code should be able to #include any header file without the fear that
the header file will go allocating memory. This is a coding style
issue, similar to commit 82e9bd588563c4e22ebb55b684ebec7e310cc715.
Move the existing hwmod data from .h files to .c files.
While here, convert "omap34xx" to "omap3xxx" in the hwmod files, since
most of these structures should be reusable across all OMAP3 chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
In preparation for multi-OMAP2 kernels, split
mach-omap2/clock2xxx_data.c into mach-omap2/clock2420_data.c and
mach-omap2/clock2430_data.c. 2430 uses a different device space
physical memory layout than past or future OMAPs, and we use a
different virtual memory layout as well, which causes trouble for
architecture-level code/data that tries to support both. We tried
using offsets from the virtual base last year, but those patches never
made it upstream; so after some discussion with Tony about the best
all-around approach, we'll just grit our teeth and duplicate the
structures. The maintenance advantages of a single kernel config that
can compile and boot on OMAP2, 3, and 4 platforms are simply too
compelling.
This approach does have some nice benefits beyond multi-OMAP 2 kernel
support. The runtime size of OMAP2420-specific and OMAP2430-specific
kernels is smaller, since unused clocks for the other OMAP2 chip will
no longer be compiled in. (At some point we will mark the clock data
__initdata and allocate it during registration, which will eliminate
the runtime memory advantage.) It also makes the clock trees slightly
easier to read, since 2420-specific and 2430-specific clocks are no
longer mixed together.
This patch also splits 2430-specific clock code into its own file,
mach-omap2/clock2430.c, which is only compiled in for 2430 builds -
mostly for organizational clarity.
While here, fix a bug in the OMAP2430 clock tree: "emul_ck" was
incorrectly marked as being 2420-only, when actually it is present on
both OMAP2420 and OMAP2430.
Thanks to Tony for some good discussions about how to approach this
problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
|
|
clock34xx_data.c now contains data for the OMAP34xx family, the
OMAP36xx family, and the OMAP3517 family, so rename it to
clock3xxx_data.c. Rename clock34xx.c to clock3xxx.c, and move the
chip family-specific clock functions to clock34xx.c, clock36xx.c, or
clock3517.c, as appropriate. So now "clock3xxx.*" refers to the OMAP3
superset.
The main goal here is to prepare to compile chip family-specific clock
functions only for kernel builds that target that chip family. To get to
that point, we also need to add CONFIG_SOC_* options for those other
chip families; that will be done in future patches, planned for 2.6.35.
OMAP4 is also affected by this. It duplicated the OMAP3 non-CORE DPLL
clkops structure. The OMAP4 variant of this clkops structure has been
removed, and since there was nothing else currently in clock44xx.c, it
too has been removed -- it can always be added back later when there
is some content for it. (The OMAP4 clock autogeneration scripts have been
updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
This patch removes the L4 wakeup io mapping section for omap3
and omap4. L4 wakeup space is part of 4MB L4 space which is
already mapped and hence remove the overlapped mapping.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace ARCH_OMAP34XX with ARCH_OMAP3
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Convert ARCH_OMAP24XX to ARCH_OMAP2
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix omap2_map_common_io for multi-omap
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rename the omap2_clk_init() in the OMAP2, 3, and 4 clock code to be
omap2xxx_clk_init(), omap3xxx_clk_init(), etc. Remove all traces of
the (commented) old virt_prcm_set code from omap3xxx_clk_init() and
omap4xxx_clk_init(), since this will be handled with the OPP code that
is cooking in the PM branch.
After this patch, there should be very little else in the clock code
that blocks a multi-OMAP 2+3 kernel. (OMAP2420+OMAP2430 still has some
outstanding issues that need to be resolved; this is pending on some
additions to the hwmod data.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong. These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains. For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.
Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Port the APIs to support the OMAP4 clockdomain framework.
Also take care of the compiling requirements for the same.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
The proper Macros have to be used for platform specific calls and
some of the compiling requirements and init calls are taken care of.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
|
|
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Remove duplicated #include('s) in
arch/arm/mach-omap2/clock34xx.c
arch/arm/mach-omap2/io.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Remove old mux code for 34xx
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
This patch enables omap_serial_early_init() function for OMAP4430
SDP. Without this the bootup would throw oops in omap_serial_init().
Note that the ifndef CONFIG_ARCH_OMAP4 is split into two sections
to enable omap_serial_early_init(). This ifndef cannot be removed
until omap4 clock framework is implemented.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Tony Lindgren <tony@atomide.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds few necessary peripherals for OMAP4.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like these patches were not tested that well..
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Connect the omap_hwmod code to the kernel boot. Create some basic
interconnect and device structures for OMAP2/3 chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface. Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.
Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them. Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput(). Jouni signed off on Tero's patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>
|
|
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
On the OMAP3, initialize SDRC timings when the kernel boots. This ensures
that the kernel is running with known, optimized SDRC timings, rather than
whatever was configured by the bootloader.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to
mach-omap2/sdrc.c. Rename the OMAP2xxx-specific functions to use an
'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the
function names rather than "memory." Mark several functions
as static that should not be used outside the sdrc2xxx.c file.
linux-omap source commit is bf1612b9d8d29379558500cd5de9ae0367c41fc4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the contents of the arch/arm/mach-omap2/memory.h file to the
existing mach/sdrc.h file, and remove memory.h. Modify files which
include memory.h to include asm/arch/sdrc.h instead.
linux-omap source commit is e7ae2d89921372fc4b9712a32cc401d645597807.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/mach-omap2/gpmc.c
arch/arm/mach-omap2/irq.c
|
|
Add minimal omap3430 support based on earlier patches from
Syed Mohammed Khasim. Also merge in omap34xx SRAM support
from Karthik Dasu and use consistent naming for sram init
functions.
Also do following changes that make 34xx support usable:
- Remove unused sram.c functions for 34xx
- Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally
in entry-macro.S
- Update mach-omap2/io.c to support 2420, 2430, and 34xx
- Also merge in 34xx GPMC changes to add fields wr_access and
wr_data_mux_bus from Adrian Hunter
- Remove memory initialization call omap2_init_memory() until
until more generic memory initialization patches are posted.
It's OK to rely on bootloader initialization until then.
Signed-off-by: Syed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Karthik Dasu<karthik-dp@ti.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Misc updates from linux-omap tree, mostly to update common
device initialization and add missing defines from linux-omap
tree. Also some changes to make room for adding 34xx in
following patches.
Note that the I2C resources are now set up in
arch/arm/plat-omap/i2c.c helper, and can be removed
from devices.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add clockdomain definitions for OMAP24xx and OMAP34xx chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add powerdomains common to both OMAP2 and OMAP3 (WKUP and GFX/SGX).
Modify mach-omap2/io.c to initialize the powerdomain code on boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch enables OMAP2 to boot.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Place SMS and SDRC into smart idle mode
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
- in addition to fixed FB regions - as passed by the bootloader -
allow dynamic allocations
- do some more checking against overlapping / reserved regions
- move the FB specific parts out from sram.c to fb.c
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch syncs omap specific core code with linux-omap.
Most of the changes are needed to fix bitrot caused by
driver updates in linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Implement basic support for General-Purpose Memory Controller
as found on OMAP2420.
Dynamic CS address space allocation still needs to be done.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
