| Age | Commit message (Collapse) | Author |
|---|
|
updates to the fsl-mc node for full functionality:
-msi-parent is needed for interrupt support
-ranges is needed to enable the bus driver to translate bus addresses
-dpmac nodes provide a basis for relating dpmac objects to PHYs
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.
The chip-specific compatible "fsl,ls2080a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.
The chip-specific compatible "fsl,ls1043a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds dts nodes for DSPI on LS1043A-RDB.
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1043a-QDS board is a high-performance computing, evaluation,
development, and test platform supporting the LS1043a SoC.
shawn.guo: sort the entries in Makefile alphabetcially
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"The arm64 device tree changes make up an increasing portion of the
overall changes, so they are kept separate from the 32-bit devicetree
changes and from the other arm64 updates.
Newly added SoCs and boards are:
- 96Boards Husky board
- AMD Overdrive board
- Amlogic S905 SoC and related Tronsmart boxes
- Annapurna Labs Alpine family and development board
- Broadcom Vulcan servers
- Broadcom Northstar 2 SoC
- Marvell Armada 3700 family and development board
- Qualcomm MSM8996 SoC
Additional devices are enabled for existing platforms from Applied
Micro, Hisilicon, Mediatek, Qualcomm, and Renesas and there are a
couple of other updates for Rockchip, Xilinx and NXP/Freescale"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (102 commits)
ARM64: dts: amlogic: Add Tronsmart Vega S95 configs
Documentation: devicetree: amlogic: Document Tronsmart Vega S95 boards
ARM64: dts: Prepare configs for Amlogic Meson GXBaby
Documentation: devicetree: amlogic: Document Meson GXBaby
devicetree: bindings: Add vendor prefix for Tronsmart
arm64: dts: qcom: Fix MPP's function used for LED control
arm64: dts: alpine: add the MSIX node in the Alpine v2 dtsi
arm64: dts: add the Alpine v2 EVP
arm64: dts: marvell: re-order Device Tree nodes for Armada AP806
arm64: dts: marvell: update Armada AP806 clock description
arm64: dts: marvell: add Device Tree files for Armada 7K/8K
arm64: dts: apm: Add DT node for X-Gene v2 SLIMpro Mailbox I2C Driver
arm64: dts: apm: Mailbox device tree node for APM X-Gene v2 platform.
arm64: dts: apm: Add DT node for X-Gene v1 SLIMpro Mailbox I2C Driver
arm64: dts: apm: mailbox device tree node for APM X-Gene platform.
arm64: dts: apm: Update GPIO to control power-off on X-Gene v2 platforms
arm64: dts: apm: Update GPIO standby controller DT node for X-Gene v2 platforms
arm64: dts: apm: Update GPIO to control power-off on X-Gene v1 platforms
arm64: dts: salvator-x: enable USB 2.0 Host of channel 1 and 2
arm64: dts: salvator-x: enable usb2_phy of channel 1 and 2
...
|
|
The patch adds LS2085a to PCIe compatible to fix the compatibility
issue when using firmware with LS2085a compatible property.
Signed-off-by: Minghuan Lian <minghuan.lian@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add "snps,quirk-frame-length-adjustment" property to USB3 node for
erratum A009116. This property provides value of GFLADJ_30MHZ for post
silicon frame length adjustment.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for
them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
dts/ls2080a: Update DTSI to add support of SP805 WDT
Documentation: DT: Add entry for ARM SP805-WDT
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
arm64: dts: hikey: add label properties to UARTs
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
arm64: dts: apq8016-sbc: enable UART0 on LS connector
arm64: dts: juno: Add idle-states to device tree
arm64: dts: Added syscon-reboot node for FSL's LS2080A SoC
arm64: dts: add LS1043a-RDB board support
arm64: dts: add Freescale LS1043a SoC support
Documentation: DT: Add entry for Freescale LS1043a-RDB board
arm64: dts: uniphier: add PH1-LD10 SoC/board support
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
...
|
|
This patch updates the LS2080a DTSI (DTS Include) file to add
support for eight SP805 Watchdog units which can be used to
reset the eight Cortex-A57 cores available on LS2080A.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Added sys-reboot node to the FSL's LS2080A SoC DT to leverage
the ARM-generic reboot mechanism for this SoC. This mechanism
is enabled through CONFIG_POWER_RESET_SYSCON.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Wenbin Song <Wenbin.Song@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
LS1043a is an SoC with 4 ARMv8 A53 cores and most other IP blocks are
similar to LS1021a which also complies to Freescale Chassis 2.1 spec.
Created LS1043a SoC DTSI file to be included by board level DTS files.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Wenbin Song <Wenbin.Song@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6ce0 ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
This patch adds build support for LS2080a QDS & RDB board DTS files
in the arm64 DTS Makefile.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the LS2080a DTS files for QDS and RDB boards
which support the LS2080a SoC.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch updates the LS2080a simulator DTS to add support of various
peripherals which are supported on the simulator platform and explicitly
disables those which are yet not supported on the platform.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch removes the same from the .dtsi and .dts
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch updates the LS2080a DTSI (DTS Include) file to add
support for the following peripherals:
- USB 3.0 Host
- PMU
- CCN-504
- SATA
- SPI
- PCIe
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Freescale is renaming the LS2085A SoC to LS2080A. This patch
addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Freescale will be a spinning-out a set of ARMv8 based SoCs which
will be based on a similar overall SoC architecture. So, this patch
converts the existing infrastructure in the arm64/dts, arm64/Kconfig
and arm64/configs to use the generic convention ARCH_LAYERSCAPE
in place of the more specific FSL_LS2085A, to save code duplication
later-on.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the device tree support for FSL LS2085A SoC
based on ARMv8 architecture.
Following levels of DTSI/DTS files have been created for the
LS2085A SoC family:
- fsl-ls2085a.dtsi:
DTS-Include file for FSL LS2085A SoC.
- fsl-ls2085a-simu.dts:
DTS file for FSL LS2085a software simulator model.
In addition, this patch adds build support for FSL's LS2085A
simulator model in arm64 dts Makefile.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnab Basu <arnab_basu@rocketmail.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
