| Age | Commit message (Collapse) | Author |
|---|
|
sleep and avoiding waking kswapd
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.4.
s390:
A bunch of fixes and optimizations for interrupt and time handling.
PPC:
Mostly bug fixes.
ARM:
No big features, but many small fixes and prerequisites including:
- a number of fixes for the arch-timer
- introducing proper level-triggered semantics for the arch-timers
- a series of patches to synchronously halt a guest (prerequisite
for IRQ forwarding)
- some tracepoint improvements
- a tweak for the EL2 panic handlers
- some more VGIC cleanups getting rid of redundant state
x86:
Quite a few changes:
- support for VT-d posted interrupts (i.e. PCI devices can inject
interrupts directly into vCPUs). This introduces a new
component (in virt/lib/) that connects VFIO and KVM together.
The same infrastructure will be used for ARM interrupt
forwarding as well.
- more Hyper-V features, though the main one Hyper-V synthetic
interrupt controller will have to wait for 4.5. These will let
KVM expose Hyper-V devices.
- nested virtualization now supports VPID (same as PCID but for
vCPUs) which makes it quite a bit faster
- for future hardware that supports NVDIMM, there is support for
clflushopt, clwb, pcommit
- support for "split irqchip", i.e. LAPIC in kernel +
IOAPIC/PIC/PIT in userspace, which reduces the attack surface of
the hypervisor
- obligatory smattering of SMM fixes
- on the guest side, stable scheduler clock support was rewritten
to not require help from the hypervisor"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (123 commits)
KVM: VMX: Fix commit which broke PML
KVM: x86: obey KVM_X86_QUIRK_CD_NW_CLEARED in kvm_set_cr0()
KVM: x86: allow RSM from 64-bit mode
KVM: VMX: fix SMEP and SMAP without EPT
KVM: x86: move kvm_set_irq_inatomic to legacy device assignment
KVM: device assignment: remove pointless #ifdefs
KVM: x86: merge kvm_arch_set_irq with kvm_set_msi_inatomic
KVM: x86: zero apic_arb_prio on reset
drivers/hv: share Hyper-V SynIC constants with userspace
KVM: x86: handle SMBASE as physical address in RSM
KVM: x86: add read_phys to x86_emulate_ops
KVM: x86: removing unused variable
KVM: don't pointlessly leave KVM_COMPAT=y in non-KVM configs
KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
KVM: arm/arm64: Clean up vgic_retire_lr() and surroundings
KVM: arm/arm64: Optimize away redundant LR tracking
KVM: s390: use simple switch statement as multiplexer
KVM: s390: drop useless newline in debugging data
KVM: s390: SCA must not cross page boundaries
KVM: arm: Do not indent the arguments of DECLARE_BITMAP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"This time including:
- A new IOMMU driver for s390 pci devices
- Common dma-ops support based on iommu-api for ARM64. The plan is
to use this as a basis for ARM32 and hopefully other architectures
as well in the future.
- MSI support for ARM-SMMUv3
- Cleanups and dead code removal in the AMD IOMMU driver
- Better RMRR handling for the Intel VT-d driver
- Various other cleanups and small fixes"
* tag 'iommu-updates-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/vt-d: Fix return value check of parse_ioapics_under_ir()
iommu/vt-d: Propagate error-value from ir_parse_ioapic_hpet_scope()
iommu/vt-d: Adjust the return value of the parse_ioapics_under_ir
iommu: Move default domain allocation to iommu_group_get_for_dev()
iommu: Remove is_pci_dev() fall-back from iommu_group_get_for_dev
iommu/arm-smmu: Switch to device_group call-back
iommu/fsl: Convert to device_group call-back
iommu: Add device_group call-back to x86 iommu drivers
iommu: Add generic_device_group() function
iommu: Export and rename iommu_group_get_for_pci_dev()
iommu: Revive device_group iommu-ops call-back
iommu/amd: Remove find_last_devid_on_pci()
iommu/amd: Remove first/last_device handling
iommu/amd: Initialize amd_iommu_last_bdf for DEV_ALL
iommu/amd: Cleanup buffer allocation
iommu/amd: Remove cmd_buf_size and evt_buf_size from struct amd_iommu
iommu/amd: Align DTE flag definitions
iommu/amd: Remove old alias handling code
iommu/amd: Set alias DTE in do_attach/do_detach
iommu/amd: WARN when __[attach|detach]_device are called with irqs enabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
|
|
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.4-rc1
Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.
Conflicts:
arch/x86/include/asm/kvm_host.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking changes from Ingo Molnar:
"The main changes in this cycle were:
- More gradual enhancements to atomic ops: new atomic*_read_ctrl()
ops, synchronize atomic_{read,set}() ordering requirements between
architectures, add atomic_long_t bitops. (Peter Zijlstra)
- Add _{relaxed|acquire|release}() variants for inc/dec atomics and
use them in various locking primitives: mutex, rtmutex, mcs, rwsem.
This enables weakly ordered architectures (such as arm64) to make
use of more locking related optimizations. (Davidlohr Bueso)
- Implement atomic[64]_{inc,dec}_relaxed() on ARM. (Will Deacon)
- Futex kernel data cache footprint micro-optimization. (Rasmus
Villemoes)
- pvqspinlock runtime overhead micro-optimization. (Waiman Long)
- misc smaller fixlets"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM, locking/atomics: Implement _relaxed variants of atomic[64]_{inc,dec}
locking/rwsem: Use acquire/release semantics
locking/mcs: Use acquire/release semantics
locking/rtmutex: Use acquire/release semantics
locking/mutex: Use acquire/release semantics
locking/asm-generic: Add _{relaxed|acquire|release}() variants for inc/dec atomics
atomic: Implement atomic_read_ctrl()
atomic, arch: Audit atomic_{read,set}()
atomic: Add atomic_long_t bitops
futex: Force hot variables into a single cache line
locking/pvqspinlock: Kick the PV CPU unconditionally when _Q_SLOW_VAL
locking/osq: Relax atomic semantics
locking/qrwlock: Rename ->lock to ->wait_lock
locking/Documentation/lockstat: Fix typo - lokcing -> locking
locking/atomics, cmpxchg: Privatize the inclusion of asm/cmpxchg.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI changes from Ingo Molnar:
"The main changes in this cycle were:
- further EFI code generalization to make it more workable for ARM64
- various extensions, such as 64-bit framebuffer address support,
UEFI v2.5 EFI_PROPERTIES_TABLE support
- code modularization simplifications and cleanups
- new debugging parameters
- various fixes and smaller additions"
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
efi: Fix warning of int-to-pointer-cast on x86 32-bit builds
efi: Use correct type for struct efi_memory_map::phys_map
x86/efi: Fix kernel panic when CONFIG_DEBUG_VIRTUAL is enabled
efi: Add "efi_fake_mem" boot option
x86/efi: Rename print_efi_memmap() to efi_print_memmap()
efi: Auto-load the efi-pstore module
efi: Introduce EFI_NX_PE_DATA bit and set it from properties table
efi: Add support for UEFIv2.5 Properties table
efi: Add EFI_MEMORY_MORE_RELIABLE support to efi_md_typeattr_format()
efifb: Add support for 64-bit frame buffer addresses
efi/arm64: Clean up efi_get_fdt_params() interface
arm64: Use core efi=debug instead of uefi_debug command line parameter
efi/x86: Move efi=debug option parsing to core
drivers/firmware: Make efi/esrt.c driver explicitly non-modular
efi: Use the generic efi.memmap instead of 'memmap'
acpi/apei: Use appropriate pgprot_t to map GHES memory
arm64, acpi/apei: Implement arch_apei_get_mem_attributes()
arm64/mm: Add PROT_DEVICE_nGnRnE and PROT_NORMAL_WT
acpi, x86: Implement arch_apei_get_mem_attributes()
efi, x86: Rearrange efi_mem_attributes()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
|
|
Pull EDAC updates from Borislav Petkov:
"A bunch of fixes all over the place and some hw enablement this time.
- Convert EDAC to debugfs wrappers and make drivers use those
(Borislav Petkov)
- L3 and SoC support for xgene_edac (Loc Ho)
- AMD F15h, models 0x60-6f support to amd64_edac (Aravind
Gopalakrishnan)
- Fixes and cleanups all over the place"
* tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
EDAC: Fix PAGES_TO_MiB macro misuse
EDAC, altera: SoCFPGA EDAC should not look for ECC_CORR_EN
EDAC: Use edac_debugfs_remove_recursive()
EDAC, ppc4xx_edac: Fix module autoload for OF platform driver
Documentation/EDAC: Add reference documents section for amd64_edac
EDAC, amd64_edac: Update copyright and remove changelog
EDAC, amd64_edac: Extend scrub rate support to F15hM60h
EDAC: Don't allow empty DIMM labels
EDAC: Fix sysfs dimm_label store operation
EDAC: Fix sysfs dimm_label show operation
arm64, EDAC: Add L3/SoC DT subnodes to the APM X-Gene SoC EDAC node
EDAC, xgene: Add SoC support
EDAC, xgene: Fix possible sprintf() overflow issue
EDAC, xgene: Add L3 support
EDAC, Documentation: Update X-Gene EDAC binding for L3/SoC subnodes
EDAC, sb_edac: Fix TAD presence check for sbridge_mci_bind_devs()
EDAC, ghes_edac: Remove redundant memory_type array
EDAC, xgene: Convert to debugfs wrappers
EDAC, i5100: Convert to debugfs wrappers
EDAC, altera: Convert to debugfs wrappers
...
|
|
'x86/amd' into next
Conflicts:
drivers/iommu/amd_iommu_types.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This should be our final batch of fixes for 4.3:
- A patch from Sudeep Holla that fixes annotation of wakeup sources
properly, old unused format seems to have spread through copying.
- Two patches from Tony for OMAP. One dealing with MUSB setup
problems due to runtime PM being enabled too early on the parent
device. The other fixes IRQ numbering for OMAP1"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
usb: musb: omap2430: Fix regression caused by driver core change
ARM: OMAP1: fix incorrect INT_DMA_LCD
ARM: dts: fix gpio-keys wakeup-source property
|
|
|
|
Make sure that the task scheduler domain hierarchy is set-up correctly
on systems with single or multi-cluster topology.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now that we added special handling to the C files in libstub, move
the one remaining arm64 specific EFI stub C file to libstub as
well, so that it gets the same treatment. This should prevent future
changes from resulting in binaries that may execute incorrectly in
UEFI context.
With efi-entry.S the only remaining EFI stub source file under
arch/arm64, we can also simplify the Makefile logic somewhat.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
A kernel built with DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA doesn't
have .text aligned to a page boundary, though fixup_executable works at
page-granularity thanks to its use of create_mapping. If .text is not
page-aligned, the first page it exists in may be marked non-executable,
leading to failures when an attempt is made to execute code in said
page.
This patch upgrades ALIGN_DEBUG_RO and ALIGN_DEBUG_RO_MIN to force page
alignment for DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA kernels,
ensuring that all sections with specific RWX permission requirements are
mapped with the correct permissions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Laura Abbott <laura@labbott.name>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: da141706aea52c1a ("arm64: add better page protections to arm64")
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Trying to build with CONFIG_ZONE_DMA=n leaves visible references
to the now-undefined ZONE_DMA, resulting in a syntax error.
Hide the references behind an #ifdef instead of using IS_ENABLED.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
For reasons not entirely apparent, but now enshrined in history, the
architectural mapping of AArch32 banked registers to AArch64 registers
actually orders SP_<mode> and LR_<mode> backwards compared to the
intuitive r13/r14 order, for all modes except FIQ.
Fix the compat_<reg>_<mode> macros accordingly, in the hope of avoiding
subtle bugs with KVM and AArch32 guests.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The current arm64 Image relocation code in the UEFI stub assumes that
the dram_base argument it receives is always a multiple of 2 MB. In
reality, it is simply the lowest start address of all RAM entries in
the UEFI memory map, which means it could be any multiple of 4 KB.
Since the arm64 kernel Image needs to reside TEXT_OFFSET bytes beyond
a 2 MB aligned base, or it will fail to boot, make sure we round dram_base
to 2 MB before using it to calculate the relocation address.
Fixes: e38457c361b30c5a ("arm64: efi: prefer AllocatePages() over efi_low_alloc() for vmlinux")
Reported-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Increase the standard cacheline size to avoid having locks in the same
cacheline.
Cavium's ThunderX core implements cache lines of 128 byte size. With
current granulare size of 64 bytes (L1_CACHE_SHIFT=6) two locks could
share the same cache line leading a performance degradation.
Increasing the size fixes that.
Increasing the size has no negative impact to cache invalidation on
systems with a smaller cache line. There is an impact on memory usage,
but that's not too important for arm64 use cases.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The comparison between TASK_SIZE_64 and MODULES_VADDR does not
make any sense on arm64, it is simply something that has been
carried over from the ARM port which arm64 is based on. So drop it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
It allows a selectable timer interrupt frequency of 100, 250, 300 and 1000 HZ.
We will get better performance when choose a suitable frequency in some scene.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The <linux/mm.h> already provides the PAGE_ALIGNED macro. Let's
use this macro instead of IS_ALIGNED and passing PAGE_SIZE directly.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Acked-by: Laura Abbott <laura@labbott.name>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
test_bit and set_bit take the bit number to operate on, rather than a
mask. This patch fixes the ICACHEF_* definitions so that they represent
the bit index in __icache_flags as opposed to the mask returned by the
BIT macro.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
enable_cpu_capabilities is only called from within cpufeature.c, so it
can be declared static.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This reverts commit e306dfd06fcb44d21c80acb8e5a88d55f3d1cf63.
With this patch applied, we were the only architecture making this sort
of adjustment to the PC calculation in the unwinder. This causes
problems for ftrace, where the PC values are matched against the
contents of the stack frames in the callchain and fail to match any
records after the address adjustment.
Whilst there has been some effort to change ftrace to workaround this,
those patches are not yet ready for mainline and, since we're the odd
architecture in this regard, let's just step in line with other
architectures (like arch/arm/) for now.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit dd006da21646 ("arm64: mm: increase VA range of identity map")
introduced a mechanism to extend the virtual memory map range
to support arm64 systems with system RAM located at very high offset,
where the identity mapping used to enable/disable the MMU requires
additional translation levels to map the physical memory at an equal
virtual offset.
The kernel detects at boot time the tcr_el1.t0sz value required by the
identity mapping and sets-up the tcr_el1.t0sz register field accordingly,
any time the identity map is required in the kernel (ie when enabling the
MMU).
After enabling the MMU, in the cold boot path the kernel resets the
tcr_el1.t0sz to its default value (ie the actual configuration value for
the system virtual address space) so that after enabling the MMU the
memory space translated by ttbr0_el1 is restored as expected.
Commit dd006da21646 ("arm64: mm: increase VA range of identity map")
also added code to set-up the tcr_el1.t0sz value when the kernel resumes
from low-power states with the MMU off through cpu_resume() in order to
effectively use the identity mapping to enable the MMU but failed to add
the code required to restore the tcr_el1.t0sz to its default value, when
the core returns to the kernel with the MMU enabled, so that the kernel
might end up running with tcr_el1.t0sz value set-up for the identity
mapping which can be lower than the value required by the actual virtual
address space, resulting in an erroneous set-up.
This patchs adds code in the resume path that restores the tcr_el1.t0sz
default value upon core resume, mirroring this way the cold boot path
behaviour therefore fixing the issue.
Cc: <stable@vger.kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: dd006da21646 ("arm64: mm: increase VA range of identity map")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
If the STXR instruction fails in the SWP emulation code, we leave *data
overwritten with the loaded value, therefore corrupting the data written
by a subsequent, successful attempt.
This patch re-jigs the code so that we only write back to *data once we
know that the update has happened.
Cc: <stable@vger.kernel.org>
Fixes: bd35a4adc413 ("arm64: Port SWP/SWPB emulation support from arm")
Reported-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We have been getting away with using a void* for the physical
address of the UEFI memory map, since, even on 32-bit platforms
with 64-bit physical addresses, no truncation takes place if the
memory map has been allocated by the firmware (which only uses
1:1 virtually addressable memory), which is usually the case.
However, commit:
0f96a99dab36 ("efi: Add "efi_fake_mem" boot option")
adds code that clones and modifies the UEFI memory map, and the
clone may live above 4 GB on 32-bit platforms.
This means our use of void* for struct efi_memory_map::phys_map has
graduated from 'incorrect but working' to 'incorrect and
broken', and we need to fix it.
So redefine struct efi_memory_map::phys_map as phys_addr_t, and
get rid of a bunch of casts that are now unneeded.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: izumi.taku@jp.fujitsu.com
Cc: kamezawa.hiroyu@jp.fujitsu.com
Cc: linux-efi@vger.kernel.org
Cc: matt.fleming@intel.com
Link: http://lkml.kernel.org/r/1445593697-1342-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
updates the bindings documents and dtsi file according to the review
comments[https://lkml.org/lkml/2015/9/21/670] from Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* acpi-init:
clocksource: cosmetic: Drop OF 'dependency' from symbols
clocksource / arm_arch_timer: Convert to ACPI probing
clocksource: Add new CLKSRC_{PROBE,ACPI} config symbols
clocksource / ACPI: Add probing infrastructure for ACPI-based clocksources
irqchip / GIC: Convert the GIC driver to ACPI probing
irqchip / ACPI: Add probing infrastructure for ACPI-based irqchips
ACPI: Add early device probing infrastructure
|
|
If we panic in hyp mode, we inject a call to panic() into the EL1N host
kernel. If a guest context is active, we first attempt to restore the
minimal amount of state necessary to execute the host kernel with
restore_sysregs.
However, the SP is restored as part of restore_common_regs, and so we
may return to the host's panic() function with the SP of the guest. Any
calculations based on the SP will be bogus, and any attempt to access
the stack will result in recursive data aborts.
When running Linux as a guest, the guest's EL1N SP is like to be some
valid kernel address. In this case, the host kernel may use that region
as a stack for panic(), corrupting it in the process.
Avoid the problem by restoring the host SP prior to returning to the
host. To prevent misleading backtraces in the host, the FP is zeroed at
the same time. We don't need any of the other "common" registers in
order to panic successfully.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: <kvmarm@lists.cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The ARM architecture only saves the exit class to the HSR (ESR_EL2 for
arm64) on synchronous exceptions, not on asynchronous exceptions like an
IRQ. However, we only report the exception class on kvm_exit, which is
confusing because an IRQ looks like it exited at some PC with the same
reason as the previous exit. Add a lookup table for the exception index
and prepend the kvm_exit tracepoint text with the exception type to
clarify this situation.
Also resolve the exception class (EC) to a human-friendly text version
so the trace output becomes immediately usable for debugging this code.
Cc: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We introduce kvm_arm_halt_guest and resume functions. They
will be used for IRQ forward state change.
Halt is synchronous and prevents the guest from being re-entered.
We use the same mechanism put in place for PSCI former pause,
now renamed power_off. A new flag is introduced in arch vcpu state,
pause, only meant to be used by those functions.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The kvm_vcpu_arch pause field is renamed into power_off to prepare
for the introduction of a new pause field. Also vcpu_pause is renamed
into vcpu_sleep since we will sleep until both power_off and pause are
false.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
vhost drivers provide guest VMs with better I/O performance and lower
CPU utilization. This patch allows users to select vhost devices under
KVM configuration menu on ARM. This makes vhost support on arm/arm64
on a par with other architectures (e.g. x86, ppc).
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We currently schedule a soft timer every time we exit the guest if the
timer did not expire while running the guest. This is really not
necessary, because the only work we do in the timer work function is to
kick the vcpu.
Kicking the vcpu does two things:
(1) If the vpcu thread is on a waitqueue, make it runnable and remove it
from the waitqueue.
(2) If the vcpu is running on a different physical CPU from the one
doing the kick, it sends a reschedule IPI.
The second case cannot happen, because the soft timer is only ever
scheduled when the vcpu is not running. The first case is only relevant
when the vcpu thread is on a waitqueue, which is only the case when the
vcpu thread has called kvm_vcpu_block().
Therefore, we only need to make sure a timer is scheduled for
kvm_vcpu_block(), which we do by encapsulating all calls to
kvm_vcpu_block() with kvm_timer_{un}schedule calls.
Additionally, we only schedule a soft timer if the timer is enabled and
unmasked, since it is useless otherwise.
Note that theoretically userspace can use the SET_ONE_REG interface to
change registers that should cause the timer to fire, even if the vcpu
is blocked without a scheduled timer, but this case was not supported
before this patch and we leave it for future work for now.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).
Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The keyboard driver for GPIO buttons(gpio-keys) checks for one of the
two boolean properties to enable gpio buttons as wakeup source:
1. "wakeup-source" or
2. the legacy "gpio-key,wakeup"
However juno, ste-snowball and emev2-kzm9d dts file have a undetected
"wakeup" property to indictate the wakeup source.
This patch fixes it by making use of "wakeup-source" property.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The hwcap string arrays used for generating the contents of
/proc/cpuinfo are currently arrays of non-const pointers.
There's no need for these pointers to be mutable, so this patch makes
them const so that they can be moved to .rodata.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Use the system wide safe value from the new API for safer
decisions
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Tested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Use the system wide value of ID_AA64DFR0 to make safer decisions
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The FP/ASIMD is detected in fpsimd_init(), which is built-in
unconditionally. Lets move the hwcap handling to the central place.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Extend struct arm64_cpu_capabilities to handle the HWCAP detection
and make use of the system wide value of the feature registers for
a reliable set of HWCAPs.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now that we can reliably read the system wide safe value for a
feature register, use that to compute the system capability.
This patch also replaces the 'feature-register-specific'
methods with a generic routine to check the capability.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
At the moment we run through the arm64_features capability list for
each CPU and set the capability if one of the CPU supports it. This
could be problematic in a heterogeneous system with differing capabilities.
Delay the CPU feature checks until all the enabled CPUs are up(i.e,
smp_cpus_done(), so that we can make better decisions based on the
overall system capability. Once we decide and advertise the capabilities
the alternatives can be applied. From this state, we cannot roll back
a feature to disabled based on the values from a new hotplugged CPU,
due to the runtime patching and other reasons. So, for all new CPUs,
we need to make sure that they have the established system capabilities.
Failing which, we bring the CPU down, preventing it from turning online.
Once the capabilities are decided, any new CPU booting up goes through
verification to ensure that it has all the enabled capabilities and also
invokes the respective enable() method on the CPU.
The CPU errata checks are not delayed and is still executed per-CPU
to detect the respective capabilities. If we ever come across a non-errata
capability that needs to be checked on each-CPU, we could introduce them via
a new capability table(or introduce a flag), which can be processed per CPU.
The next patch will make the feature checks use the system wide
safe value of a feature register.
NOTE: The enable() methods associated with the capability is scheduled
on all the CPUs (which is the only use case at the moment). If we need
a different type of 'enable()' which only needs to be run once on any CPU,
we should be able to handle that when needed.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
[catalin.marinas@arm.com: static variable and coding style fixes]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
check_cpu_capabilities runs through a given list of caps and
checks if the system has the cap, updates the system capability
bitmap and also runs any enable() methods associated with them.
All of this is not quite obvious from the name 'check'. This
patch splits the check_cpu_capabilities into two parts :
1) update_cpu_capabilities
=> Runs through the given list and updates the system
wide capability map.
2) enable_cpu_capabilities
=> Runs through the given list and invokes enable() (if any)
for the caps enabled on the system.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Suggested-by: Catalin Marinas <catalin.marinsa@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
