| Age | Commit message (Collapse) | Author |
|---|
|
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
spi: fix probe/remove section markings
Add OMAP spi100k driver
spi-imx: don't access struct device directly but use dev_get_platdata
spi-imx: Add mx25 support
spi-imx: use positive logic to distinguish cpu variants
spi-imx: correct check for platform_get_irq failing
ARM: NUC900: Add spi driver support for nuc900
spi: SuperH MSIOF SPI Master driver V2
spi: fix spidev compilation failure when VERBOSE is defined
spi/au1550_spi: fix setupxfer not to override cfg with zeros
spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove
spi/i.MX: fix broken error handling for gpio_request
spi/i.mx: drain MXC SPI transfer buffer when probing device
MAINTAINERS: add SPI co-maintainer.
spi/xilinx_spi: fix incorrect casting
spi/mpc52xx-spi: minor cleanups
xilinx_spi: add a platform driver using the xilinx_spi common module.
xilinx_spi: add support for the DS570 IP.
xilinx_spi: Switch to iomem functions and support little endian.
xilinx_spi: Split into of driver and generic part.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (58 commits)
mfd: Add twl6030 regulator subdevices
regulator: Add support for twl6030 regulators
rtc: Add twl6030 RTC support
mfd: Add support for twl6030 irq framework
mfd: Rename twl4030_ routines in twl-regulator.c
mfd: Rename twl4030_ routines in rtc-twl.c
mfd: Rename all twl4030_i2c*
mfd: Rename twl4030* driver files to enable re-use
mfd: Clarify twl4030 return value for read and write
mfd: Add all twl4030 regulators to the twl4030 mfd driver
mfd: Don't set mc13783 ADREFMODE for touch conversions
mfd: Remove ezx-pcap defines for custom led gpio encoding
mfd: Near complete mc13783 rewrite
mfd: Remove build time warning for WM835x register default tables
mfd: Force I2C to be built in when building WM831x
mfd: Don't allow wm831x to be built as a module
mfd: Fix incorrect error check for wm8350-core
mfd: Fix twl4030 warning
gpiolib: Implement gpio_to_irq() for wm831x
mfd: Remove default selection of AB4500
...
|
|
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
|
|
No idea if this platform actually uses cpufreq_get(), but it doesn't
have any cpufreq drivers. That's not to say it doesn't use cpufreq_get()
in its drivers. LH7a40x is unmaintained anyhow, and should probably
be killed off.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix:
arch/arm/mach-sa1100/generic.c:117: error: redefinition of 'cpufreq_get'
include/linux/cpufreq.h:299: error: previous definition of 'cpufreq_get' was here
cpufreq_get() is used on these platforms to tell drivers what the CPU
frequency is, and therefore the bus frequency - which is critical for
setting the PCMCIA and LCD timings. Adding ifdefs to these drivers to
select cpufreq_get() or some other interface adds confusion. Making
these drivers use some other interface for the normal paths and cpufreq
stuff for the cpufreq notifier is insane as well.
(Why x86 can't provide a version of cpufreq_get() which returns the
CPU frequency when CPUFREQ is disabled is beyond me, rather than
requiring a dummy zero-returning cpufreq_get(). Especially as they
do:
unsigned long khz = cpufreq_get(cpu);
if (!khz)
khz = tsc_khz;
In other words, if CPUFREQ is disabled, get it from tsc_khz - why
not provide a dummy cpufreq_get() which returns tsc_khz?)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The power scripts optimisation was mainly done by:
Tero Kristo <tero.kristo@nokia.com> and
Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
I'm only refactoring and testing it against the mainline kernel.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
|
|
Anders Grafström reports that footbridge fails to build after 1c4a4f4.
Fix this by adding the necessary definitions for __pfn_to_bus and
__bus_to_pfn.
Reported-by: Anders Grafström <anders.grafstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When the VFP notifier is called for flush_thread(), we may be
preemptible, meaning we might migrate to another CPU, which means
referencing the current CPU number without some form of locking is
invalid, and can cause data corruption.
For the most cases, this isn't a problem since atomic notifiers are run
under rcu lock, which for most configurations results in preemption
being disabled - except when the preemptable tree-based rcu
implementation is selected.
Let's make it safe anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The Arcom Zeus CF slot requires the same kind of support as the Viper.
To avoid code duplication, introduce a platform device that abstracts
the differences.
This also allows for the removal of the ugly export of viper_cf_rst().
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: GTWX5715 platform only has two PCI IRQ lines, not four.
IXP4xx: Introduce IXP4XX_GPIO_IRQ(n) macro and convert IXP4xx platform files.
IXP4xx: move Gemtek GTWX5715 platform macros to the platform code.
IXP4xx: Remove unused Motorola PrPMC1100 platform macros.
IXP4xx: move FSG platform macros to the platform code.
IXP4xx: move DSM G600 platform macros to the platform code.
IXP4xx: move NAS100D platform macros to the platform code.
IXP4xx: move NSLU2 platform macros to the platform code.
IXP4xx: move Coyote platform macros to the platform code.
IXP4xx: move AVILA platform macros to the platform code.
IXP4xx: move IXDP425 platform macros to the platform code.
IXP4xx: Extend PCI MMIO indirect address space to 1 GB.
IXP4xx: Fix compilation failure with CONFIG_IXP4XX_INDIRECT_PCI.
IXP4xx: Drop "__ixp4xx_" prefix from in/out/ioread/iowrite functions for clarity.
IXP4xx: Rename indirect MMIO primitives from __ixp4xx_* to __indirect_*.
IXP4xx: Ensure index is positive in irq_to_gpio() and npe_request().
ARM: fix insl() and outsl() endianness on IXP4xx architecture.
IXP4xx: Fix normally-disabled debugging text in drivers/net/arm/ixp4xx_eth.c.
IXP4xx: change the timer base frequency to 66.666000 MHz.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (75 commits)
omap3: Fix OMAP35XX_REV macros
omap: serial: fix non-empty uart fifo read abort
omap3: Zoom2/3: Update hsmmc board config params
omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
omap3: id code detection 3525 vs 3515
omap3: rx51: Use wl1251 in SPI mode 3
omap3: zoom2/3: make MMC slot work again
omap1: htcherald: Update defconfig to include mux support
omap1: LCD_DMA: Use some define rather than a hexadecimal
omap: header: remove unused data-type
omap: arch/arm/plat-omap/devices.c - sort alphabetically
omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
OMAP3: serial - allow platforms specify which UARTs to initialize
omap3: cm-t35: add mux initialization
OMAP4: Sync up omap4430 defconfig
OMAP4: Remove the secondary wait loop
OMAP4: AuxCoreBoot registers only accessible in secure mode
OMAP4: Fix SRAM base and size
OMAP4: Fix cpu detection
omap3: pandora: board file updates for .33
...
|
|
* 'for-linus' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
HTC Dream: mmc compilation fixes
video: Allow selecting MSM framebuffer in Kconfig
Add arm msm maintainer entry
msm: Add memory map for HTC Dream
msm: add minimal board file for HTC Dream device
msm: make debugging UART (for DEBUG_LL) configurable
|
|
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
|
|
OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.
OMAP3xxx:
UART IP revision >= 0x52 have this issue
MVR register format is:
Bits Field Name Description Type Reset
31:8 RESERVED RO 0x0
7:4 MAJOR Major revision number of the module. RO 0x--
3:0 MINOR Minor revision number of the module. RO 0x--
OMAP4xxx:
All revisions have this issue
Revision id check is not used as the format of MVR resigster has changed
For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
Bits Field Name Description Type Reset
31:30 SCHEME Scheme revision number of module RO 0x1
29:28 RESERVED RO 0x1
27:16 FUNC Function revision number of module RO 0x041
15:11 RTL Rtl revision number of module RO 0x00
10:8 MAJOR Major revision number of the module. RO 0x6
7:6 CUSTOM Custom revision number of the module. RO 0x0
5:0 MINOR Minor revision number of the module. RO 0x02
Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty
tested on zoom3(3630) board
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The TWL4030 keypad driver is not enabled by default for zoom2 and zoom3
boards.
This patch will enable the same for both zoom2 and zoom3 boards.
Tested on zoom2(3430) and zoom3(3630) boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap3: zoom2/3: make MMC slot work again
Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The existing htcherald_defconfig did not include mux support, which
prevented USB and other functionality from working out of the box.
This change updates the defconfig to add it in. It also aligns the
defconfig to the -rc8 kernel config.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Comment in omap_init_devices asks to keep init calls and their
implementations in alphabetical order, so let it be that way.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable minimum features to boot omap4430 on es1.0 samples. v2 versions
removes the "CONFIG_SYSFS_DEPRECATED_V2" since it's deprecated. Without
this older file system doesn't boot. One need to upgrade the filesystem
if getting stuck in first init function.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The secondary cores wakes up in time so the wait loop is not
necessary anymore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the public sram base address and available
size on OMAP4430.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Defconfig file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Board file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add 36xx CBP package support
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove old mux code for 34xx
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace omap_cfg_reg() with new style signal or gpio functions
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
