| Age | Commit message (Collapse) | Author |
|---|
|
Add pin muxing support for the Nokia N900 i2c controllers.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add DT OPP table for DRA7xx family of devices. This data is decoded by
OF with of_init_opp_table() helper function.
The data is based on DRA75x, DRA74x Data Manual revision F (Sept 2013).
TODO: add OPP_HIGH after AVS-Class0 is functional
NOTE: The voltage and frequency values work well only on NOM samples
and it is mandatory to use ABB/AVS Class 0 support for all OPPs.
Clock nodes are pending clock node alignment.
[nm@ti.com: cleanups and rebase to latest]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add DT OPP table for OMAP54xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
The data is based on OMAP543x ES2.0 DM Operating Condition Addendum
Version 0.6(April 2013)
NOTE: The voltage and frequency values work well only on NOM samples
and are supposed to work properly only with ABB/AVS for ALL OPPs.
TODO: Add SPEED BIN OPP after ABB and AVS support so the cpufreq works
on all samples seamlessly. Clock node is pending alignment for clock
dts conversion
[nm@ti.com: sync to latest and fixes]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
regulator smps123 supply from Palmas PMIC powers CPU0 on DRA7 EVM.
[nm@ti.com: rebase to latest]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM.
Based on a patch by J Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Correct mcspi pin descriptions to match corresponding node name and
add chip select number to be consistent with OMAP5 TRM.
Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Control module is not usb specific.
Changes the label to usb_ctrl_mod.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
NanoBone Specification:
-----------------------
CPU:
TI AM335x
Memory:
256MB DDR3
128MB NOR flash
128KB FRAM
Ethernet:
2 x 10/100 connected to SMSC LAN8710 PHY
USB:
1 x USB2.0 Type A
I2C:
2Kbit EEPROM (Microchip 24AA02)
RTC (Maxim DS1338)
GPIO Expander (Microchip MCP23017)
Expansion connector:
6 x UART
1 x MMC/SD
1 x USB2.0
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Provide alias to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.
Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add mmc1 dt node to IGEP COM AQUILA board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add nodes for McASP0 and McASP1 for AM43xx.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on beagle after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Adds sound, tlv320aic3106, mcasp1, and am335x_evm_audio_pin nodes.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add missing mcasp entries in the am33xx.dtsi include file.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.
Update as well DT properties for epwmss, aes, des.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.
Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Do not reset GPIO0 at boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.
Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.
[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
This allows the palmas pm_power_off to kick in on power off command
and switch off the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added
constants for IRQ edge/level triggered types so use it instead of
a magic number to enhance the DT readability.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Commit ad871c10b ("ARM: dts: OMAP: Add usb_otg and glue data to O
added USB OTG support for most OMAP boards but some OMAP3 boards
such as IGEP boards were not updated. This patch adds an USB OTG
device node to these board.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Enable the hdmi output and the LCD Controller on BeagleBone
Black. Also configure the correct pinmux for output of
video data from the SoC to the HDMI encoder.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm
Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
AM437x SoC has a DES3DES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
AM437x SoC has AES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
AES interrupts were previously not used, but after recent changes
to omap-aes driver, its being used.
Correct the interrupt number to have working PIO mode.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the AES module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the SHAM module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
OMAP4 has an DES3DES module that uses the omap-des crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Set bus-width to make SD card operate in 4 bit mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.
The board adds the following connectivity:
o USB OTG
o USB HOST
o HDMI
o Ethernet
o Serial Debug (3.3V)
o 2x46 pin headers
o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:
o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.
Move the fixed regulator to be at root of platform.
Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
