| Age | Commit message (Collapse) | Author |
|---|
|
Based on i.MX6 SoloX with 1GB of RAM.
https://boundarydevices.com/product/nit6_solox-imx6/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It is preferred to use the panel compatible string rather than passing the
LCD timings in the device tree.
So pass the "hannstar,hsd100pxn1" compatible string to describe
the LVDS panel on this board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 256MiB DDR3 SDRAM
ROM 128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6S-8035:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 512MiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6U-8033:
Processor Freescale i.MX 6 Dual Lite, 800MHz
RAM 1GiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6Q-1036:
Processor Freescale i.MX 6Quad, 1GHz
RAM 1GB DDR3 SDRAM 64-bit
ROM 8GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range Extended Consumer Grade (-20°C to 105°C Tj)
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing pinctrl for the RTS/CTS lines to uart1 and set the
fsl,uart-has-rtscts property on all UARTs to enable support for HW
handshake.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the pinctrl setting for the board LED from the hoggrp node
to a separate node referenced by the LED driver, so that the pin is
free to be used for different purpose when the LED driver is disabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on i.MX6 Quad Plus with 4GB of RAM.
https://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add mdio node and an appropriate PHY configuration to enable use of
the PHY interrupt for link status changes.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed95 ("pinctrl: imx: Allow parsing DT without
function nodes"), we can save this container node.
Also move the iomux node to the bottom of the file to improve
readability of the file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The spidev driver doesn't like to be instantiated via a naked 'spidev'
compatible, though it is very convenient to invoke it this way without
a dedicated SPI device for basic functional testing.
Disable the spi node by default to silence the WARN_ON() from the
spidev driver, but leave the configuration intact otherwise.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an empty line between properties and subnode in the clocks node.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the imx6*-tx6* files to this combination.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
mode
With SION set the level on such a pin is reported to the UART. So for
example when the CS5 pin is configured for GPIO mode and the level
changes this triggers an RTS interrupt on uart5.
Adding some severity to this issue: The imx uart driver currently
doesn't handle correctly irqs for changes on RI and DCD which are
enabled automatically when the respective UART is driven in DTE mode
(that is, has the fsl,dte-mode property set in the device tree). This
results in a stuck machine because the irq isn't cleared and so stalls
the CPU.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Apart from a few additions this also contains two fixes where the daisy
chain input selection register was missing. Moreover dropped _MUX from
some pins for consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Utilize the new PCIe Tx configuration to properly support the correct
values.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The TXUL-0010/-0011 modules are Computers On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM 256MB 16-bit DDR3 SDRAM
ROM 128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 85°C
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
|
|
Pull MTD updates from Brian Norris:
"NAND:
- Add sunxi_nand randomizer support
- begin refactoring NAND ecclayout structs
- fix pxa3xx_nand dmaengine usage
- brcmnand: fix support for v7.1 controller
- add Qualcomm NAND controller driver
SPI NOR:
- add new ls1021a, ls2080a support to Freescale QuadSPI
- add new flash ID entries
- support bottom-block protection for Winbond flash
- support Status Register Write Protect
- remove broken QPI support for Micron SPI flash
JFFS2:
- improve post-mount CRC scan efficiency
General:
- refactor bcm63xxpart parser, to later extend for NAND
- add writebuf size parameter to mtdram
Other minor code quality improvements"
* tag 'for-linus-20160324' of git://git.infradead.org/linux-mtd: (72 commits)
mtd: nand: remove kerneldoc for removed function parameter
mtd: nand: Qualcomm NAND controller driver
dt/bindings: qcom_nandc: Add DT bindings
mtd: nand: don't select chip in nand_chip's block_bad op
mtd: spi-nor: support lock/unlock for a few Winbond chips
mtd: spi-nor: add TB (Top/Bottom) protect support
mtd: spi-nor: add SPI_NOR_HAS_LOCK flag
mtd: spi-nor: use BIT() for flash_info flags
mtd: spi-nor: disallow further writes to SR if WP# is low
mtd: spi-nor: make lock/unlock bounds checks more obvious and robust
mtd: spi-nor: silently drop lock/unlock for already locked/unlocked region
mtd: spi-nor: wait for SR_WIP to clear on initial unlock
mtd: nand: simplify nand_bch_init() usage
mtd: mtdswap: remove useless if (!mtd->ecclayout) test
mtd: create an mtd_oobavail() helper and make use of it
mtd: kill the ecclayout->oobavail field
mtd: nand: check status before reporting timeout
mtd: bcm63xxpart: give width specifier an 'int', not 'size_t'
mtd: mtdram: Add parameter for setting writebuf size
mtd: nand: pxa3xx_nand: kill unused field 'drcmr_cmd'
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM DT changes from Arnd Bergmann:
"Here are some final updates for ARM SoC specific dts files:
- The i.MX changes were sent relatively late, and had a dependency on
the clk tree, so I delayed that a bit. Support for the new i.MX6qp
SoC and a couple of new boards is added in this branch.
- Uniphier renames a few files to match the final product names that
were decided by the company, kudos to the kernel developer(s) for
getting support upstream before the product release. Also two
boards are added. The patches were posted early enough and nice
overall, but we forgot to apply them and decided to give it some
more time in linux-next
- at91 has two small bug fixes"
* tag 'armsoc-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: uniphier: add pinmux node for I2C ch4
ARM: dts: uniphier: add @{address} to EEPROM node
ARM: dts: uniphier: add PH1-Pro4 Sanji board support
ARM: dts: uniphier: add PH1-Pro4 Ace board support
ARM: dts: uniphier: enable I2C channel 2 of ProXstream2 Gentil board
ARM: dts: uniphier: add EEPROM node for ProXstream2 Gentil board
ARM: dts: uniphier: add reference clock nodes
ARM: dts: uniphier: rework UniPhier System Bus nodes
ARM: dts: uniphier: factor out ranges property of support card
arm64: dts: uniphier: rename PH1-LD10 to PH1-LD20
ARM: dts: imx53-qsb: Fix gpio button polarity
ARM: dts: vfxxx: Add DAC node for Vybrid SoC
ARM: dts: imx6q: add missing links between ipu2 and mipi dsi
ARM: dts: imx: Add support for Advantech/GE B850v3
ARM: dts: imx: Add support for Advantech/GE B650v3
ARM: dts: imx: Add support for Advantech/GE B450v3
ARM: dts: imx: Add support for Advantech/GE Bx50v3
ARM: dts: imx: Add Advantech BA-16 Qseven module
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt2
Merge "First fixes batch for AT91 on 4.6 - DT only fixes" from Nicolas Ferre:
- prevent the boards from having glitches when inserting/removing SD card on
sama5d3/d4 Xplained. The regulators should be kept on.
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
|
|
Pull more KVM updates from Paolo Bonzini:
"Second round of KVM changes for 4.6:
- build fixes for PPC KVM
- miscellaneous bugfixes for ARM KVM
- cleanup of memory barrier and removal of redundant barriers
- x86 fixes: page tracking oops, support for old buggy KVM nested on 4.5
- support for protection keys in guests
- lockdep fix
- another conversion to simple wait queues and raw spinlocks,
backported from PREEMPT_RT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (27 commits)
KVM: page_track: fix access to NULL slot
KVM: PPC: do not compile in vfio.o unconditionally
kvm, rt: change async pagefault code locking for PREEMPT_RT
KVM/PPC: update the comment of memory barrier in the kvmppc_prepare_to_enter()
KVM/x86: update the comment of memory barrier in the vcpu_enter_guest()
KVM: Replace smp_mb() with smp_load_acquire() in the kvm_flush_remote_tlbs()
KVM/x86: Call smp_wmb() before increasing tlbs_dirty
KVM: Replace smp_mb() with smp_mb_after_atomic() in the kvm_make_all_cpus_request()
KVM/x86: Replace smp_mb() with smp_store_mb/release() in the walk_shadow_page_lockless_begin/end()
KVM: Remove redundant smp_mb() in the kvm_mmu_commit_zap_page()
KVM, pkeys: expose CPUID/CR4 to guest
KVM, pkeys: add pkeys support for permission_fault
KVM, pkeys: introduce pkru_mask to cache conditions
KVM, pkeys: save/restore PKRU when guest/host switches
x86: pkey: introduce write_pkru() for KVM
KVM, pkeys: add pkeys support for xsave state
KVM, pkeys: disable pkeys for guests in non-paging mode
KVM: x86: remove magic number with enum cpuid_leafs
KVM: MMU: return page fault error code from permission_fault
KVM: fix spin_lock_init order on x86
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.6:
- Make earlyprintk=xen work for HVM guests
- Remove module support for things never built as modules"
* tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: make platform-pci.c explicitly non-modular
drivers/xen: make sys-hypervisor.c explicitly non-modular
drivers/xen: make xenbus_dev_[front/back]end explicitly non-modular
drivers/xen: make [xen-]ballon explicitly non-modular
xen: audit usages of module.h ; remove unnecessary instances
xen/x86: Drop mode-selecting ifdefs in startup_xen()
xen/x86: Zero out .bss for PV guests
hvc_xen: make early_printk work with HVM guests
hvc_xen: fix xenboot for DomUs
hvc_xen: add earlycon support
|
|
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 8d545f32bd77 ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 1b53e3416dd0 ("ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm[64] perf updates from Will Deacon:
"I have another mixed bag of ARM-related perf patches here.
It's about 25% CPU and 75% interconnect, but with drivers/bus/
languishing without an obvious maintainer or tree, Olof and I agreed
to keep all of these PMU patches together. I suspect a whole load of
code from drivers/bus/arm-* can be moved under drivers/perf/, so
that's on the radar for the future.
Summary:
- Initial support for ARMv8.1 CPU PMUs
- Support for the CPU PMU in Cavium ThunderX
- CPU PMU support for systems running 32-bit Linux in secure mode
- Support for the system PMU in ARM CCI-550 (Cache Coherent Interconnect)"
* tag 'arm64-perf' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (26 commits)
drivers/perf: arm_pmu: avoid NULL dereference when not using devicetree
arm64: perf: Extend ARMV8_EVTYPE_MASK to include PMCR.LC
arm-cci: remove unused variable
arm-cci: don't return value from void function
arm-cci: make private functions static
arm-cci: CoreLink CCI-550 PMU driver
arm-cci500: Rearrange PMU driver for code sharing with CCI-550 PMU
arm-cci: CCI-500: Work around PMU counter writes
arm-cci: Provide hook for writing to PMU counters
arm-cci: Add helper to enable PMU without synchornising counters
arm-cci: Add routines to save/restore all counters
arm-cci: Get the status of a counter
arm-cci: write_counter: Remove redundant check
arm-cci: Delay PMU counter writes to pmu::pmu_enable
arm-cci: Refactor CCI PMU enable/disable methods
arm-cci: Group writes to counter
arm-cci: fix handling cpumask_any_but return value
arm-cci: simplify sysfs attr handling
drivers/perf: arm_pmu: implement CPU_PM notifier
arm64: dts: Add Cavium ThunderX specific PMU
...
|
|
Code that uses no modular facilities whatsoever should not be
sourcing module.h at all, since that header drags in a bunch
of other headers with it.
Similarly, code that is not explicitly using modular facilities
like module_init() but only is declaring module_param setup
variables should be using moduleparam.h and not the larger
module.h file for that.
In making this change, we also uncover an implicit use of BUG()
in inline fcns within arch/arm/include/asm/xen/hypercall.h so
we explicitly source <linux/bug.h> for that file now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Preemption must be disabled when calling smp_call_function_many
Reported-by: bartosz.wawrzyniak@tieto.com
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs.
The realview_smp_defconfig and realview_defconfig got merged into one,
so we are now down to 110 files.
For stm32, we have now added a Kconfig fragment, the first such file
on arch/arm. The purpose here is to have a shared defconfig file that
works for all boards, while the DRAM offset has to be hardwired on
NOMMU machines at compile time.
The Exynos defconfig changes depend on changes in the RTC tree, so
this is pulled in here, but has already been merged into 4.6 now"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: imx_v4_v5_defconfig: Enable initramfs support
ARM: imx_v4_v5_defconfig: Cleanup imx_v4_v5_defconfig
ARM: multi_v7_defconfig: Enable LP872x regulator support
ARM: omap2plus_defconfig: Enable LP872x regulator support
ARM: mxs_defconfig: Enable initramfs support
ARM: mxs_defconfig: Cleanup mxs_defconfig
ARM: multi_v5_defconfig: Enable initramfs support
ARM: multi_v5_defconfig: Cleanup multi_v5_defconfig
ARM: multi_v7_defconfig: enable useful configurations for Vybrid
ARM: multi_v7_defconfig: add MACH_ARTPEC6
ARM: omap2plus_defconfig: Enable AT24 eeprom
ARM: omap2plus_defconfig: Enable TI TVP5150 video decoder support
ARM: omap2plus_defconfig: Enable ISP support and dependencies
ARM: omap2plus_defconfig: Enable OMAP IOMMU support
ARM: socfpga_defconfig: enable support for initramfs/initrd support
ARM: at91/defconfig: add sama5d2 adc support in sama5_defconfig
ARM: multi_v7_defconfig: Enable BCM283x
ARM: bcm2835_defconfig: Enable RPi power domain driver
ARM: bcm2835_defconfig: Enable RPi firmware driver
ARM: bcm2835_defconfig: enable ARMv7 support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
plus a couple of related 64-bit updates:
New SoC support:
- Allwinner A83T
- Axis Artpec-6 SoC
- Mediatek MT7623 SoC
- TI Keystone K2G SoC
- ST Microelectronics stm32f469
New board or machine support:
- ARM Juno R2
- Buffalo Linkstation LS-QVL and LS-GL
- Cubietruck plus
- D-Link DIR-885L
- DT support for ARM RealView PB1176 and PB11MPCore
- Google Nexus 7
- Homlet v2
- Itead Ibox
- Lamobo R1
- LG Optimus Black
- Logicpd dm3730
- Raspberry Pi Model A
Other changes include
- Lots of updates for Qualcomm APQ8064, MSM8974 and others
- Improved support for Nokia N900 and other OMAP machines
- Common clk support for lpc32xx
- HDLCD display on ARM
- Improved stm32f429 support
- Improved Renesas device support, r8a779x and others
- Lots of Rockchip updates
- Samsung cleanups
- ADC support for Atmel SAMA5D2
- BCM2835 (Raspberry Pi) improvements
- Broadcom Northstar Plus enhancements
- OMAP GPMC rework
- Several improvements for Atmel SAMA5D2 / Xplained
- Global change to remove inofficial "arm,amba-bus" compatible
string"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (350 commits)
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus"
ARM: dts: artpec: dual-license on artpec6.dtsi
ARM: dts: ux500: add synaptics RMI4 for Ux500 TVK DT
arm64: dts: juno/vexpress: fix node name unit-address presence warnings
arm64: dts: foundation-v8: add SBSA Generic Watchdog device node
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: stm32f429: Enable Ethernet on Eval board
ARM: dts: omap3-sniper: TWL4030 keypad support
Revert "ARM: dts: DRA7: Add dt nodes for PWMSS"
ARM: dts: dm814x: dra62x: Disable wait pin monitoring for NAND
ARM: dts: dm814x: dra62x: Fix NAND device nodes
ARM: dts: stm32f429: Add Ethernet support
ARM: dts: stm32f429: Add system config bank node
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
ARM: dts: exynos: Don't overheat the Odroid XU3-Lite on high load
ARM: dts: exynos: Add cooling levels for Exynos5422/5800 CPUs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Arnd Bergmann:
"Here's our branch of ARM64 contents for this merge window, now
containing all ARM64 changes other than device tree files.
- Various new platforms get added:
* Allwinner A64 SoC
* Annapurna Labs Alpine SoCs
* Broadcom Vulcan
* Marvell Armada 3700 SoCs
* Amlogic S905
- Various defconfig changes to enable platform specific drivers
This branch includes the clk git tree to resolve a build-time
dependency"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
arm64: defconfig: Increase MMC_BLOCK_MINORS to 16
arm64: defconfig: Add Qualcomm sdhci and restart functionality
ARM64: Enable Amlogic Meson GXBaby platform
arm64: defconfig: Enable Samsung MFD and related configs
arm64: alpine: select the Alpine MSI controller driver
arm64: defconfig: enable the Alpine family
arm64: add Alpine SoC family
arm64: defconfig: Enable exynos thermal config
arm64: add defconfig options for Allwinner SoCs
arm64: defconfig: Enable DesignWare APB GPIO controller
arm64: defconfig: Add Renesas R-Car Gen3 USB 2.0 phy driver support
arm64: EXYNOS: Consolidate ARCH_EXYNOS7 symbol into ARCH_EXYNOS
clk: samsung: Don't build ARMv8 clock drivers on ARMv7
MAINTAINERS: Add entry for Broadcom Vulcan SoC
arm64: cputype info for Broadcom Vulcan
arm64: Broadcom Vulcan support
arm64: defconfig: Add Broadcom Vulcan to defconfig
arm64: update ARCH_MVEBU for Marvell Armada 7K/8K support
Documentation: arm: add Marvell Armada 7K and 8K families
Documentation: arm: add link to Armada 38x Functional Spec
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A few simple cleanups across multiple platforms, not much standing
out:
- lpc32xx removes its private implementation of the clk API, after
generic code was merged in 4.5
- all unused Makefile.boot files get removed
- a number of simplifications for shmobile
- asm/clkdev.h gets replaced with the asm-generic version after all
mach/clkdev.h implementations are gone"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: Kconfig: Get rid of old comment
ARM: shmobile: Consolidate SCU mapping code
arm: lpc32xx: remove direct control of GPIOs from shared mach file
arm: lpc32xx: remove selected HAVE_IDE
arm: lpc32xx: switch to common clock framework
ARM: Use generic clkdev.h header
ARM: plat-versatile: Remove unused clock.c file
ARM: netx: remove redundant "depends on ARCH_NETX"
ARM: integrator: remove redundant select in Kconfig
ARM: drop unused Makefile.boot of Multiplatform SoCs
ARM: mvebu: add missing of_node_put()
ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
ARM: shmobile: Typo s/MIPDR/MPIDR/
ARM: shmobile: Add includes providing forward declarations
ARM: shmobile: rcar-gen2: Make rcar_gen2_dma_contiguous static
ARM: mv78xx0: use "depends on" instead of "if" after prompt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle tuning that
was lost in a cleanup
- a small regression fix for cns3xxx PCI"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
CNS3xxx: Fix PCI cns3xxx_write_config()
MAINTAINERS: unify email addrs for Kevin Hilman
CNS3xxx: remove unused *_VIRT definitions
ARM: OMAP2+: Fix hwmod clock for l4_ls
soc: TI knav_qmss: fix dma_addr_t printing
ARM: prima2: always enable reset controller
ARM: socfpga: hide unused functions
ARM: ux500: fix ureachable iounmap()
ARM: ks8695: fix __initdata annotation
ARM: mvebu: mark mvebu_hwcc_pci_nb as __maybe_unused
ARM: mv78xx0: avoid unused function warning
ARM: orion: only select I2C_BOARDINFO when using I2C
ARM: OMAP2+: Fix out of range register access with syscon_config.max_register
ARM: OMAP3: Add cpuidle parameters table for omap3430
ARM: davinci: make I2C support optional
ARM: davinci: DA8xx+DMx combined kernels need PATCH_PHYS_VIRT
ARM: davinci: avoid unused mityomapl138_pn_info variable
ARM: davinci: limit DT support to DA850
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
...
|
|
Pull watchdog updates from Wim Van Sebroeck:
- new drivers for: NI 903x/913x watchdog driver, WinSystems EBC-C384
watchdog timer and ARM SBSA watchdog driver
- Support for NCT6102D devices
- Improvements of the generic watchdog framework (improve restart
handler, make set_timeout optional, introduce infrastructure
triggered keepalives, ...
- improvements on the pnx4008 watchdog driver
- several smaller fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (28 commits)
watchdog: Ensure that wdd is not dereferenced if NULL
watchdog: imx2: Convert to use infrastructure triggered keepalives
watchdog: dw_wdt: Convert to use watchdog infrastructure
watchdog: Add support for minimum time between heartbeats
watchdog: Make stop function optional
watchdog: Introduce WDOG_HW_RUNNING flag
watchdog: Introduce hardware maximum heartbeat in watchdog core
watchdog: Make set_timeout function optional
arm: lpc32xx: remove restart handler
arm: lpc32xx: phy3250 remove restart hook
watchdog: pnx4008: restart: support "cmd" from userspace
watchdog: pnx4008: add support for soft reset
watchdog: pnx4008: add restart handler
watchdog: pnx4008: update logging during power-on
watchdog: tangox_wdt: test clock rate to avoid division by 0
watchdog: atlas7_wdt: test clock rate to avoid division by 0
watchdog: s3c2410_wdt: Add max and min timeout values
Watchdog: introduce ARM SBSA watchdog driver
Documentation: add sbsa-gwdt driver documentation
watchdog: Add watchdog timer support for the WinSystems EBC-C384
...
|
|
Pull ARM updates from Russell King:
"Another mixture of changes this time around:
- Split XIP linker file from main linker file to make it more
maintainable, and various XIP fixes, and clean up a resulting
macro.
- Decompressor cleanups from Masahiro Yamada
- Avoid printing an error for a missing L2 cache
- Remove some duplicated symbols in System.map, and move
vectors/stubs back into kernel VMA
- Various low priority fixes from Arnd
- Updates to allow bus match functions to return negative errno
values, touching some drivers and the driver core. Greg has acked
these changes.
- Virtualisation platform udpates form Jean-Philippe Brucker.
- Security enhancements from Kees Cook
- Rework some Kconfig dependencies and move PSCI idle management code
out of arch/arm into drivers/firmware/psci.c
- ARM DMA mapping updates, touching media, acked by Mauro.
- Fix places in ARM code which should be using virt_to_idmap() so
that Keystone2 can work.
- Fix Marvell Tauros2 to work again with non-DT boots.
- Provide a delay timer for ARM Orion platforms"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (45 commits)
ARM: 8546/1: dma-mapping: refactor to fix coherent+cma+gfp=0
ARM: 8547/1: dma-mapping: store buffer information
ARM: 8543/1: decompressor: rename suffix_y to compress-y
ARM: 8542/1: decompressor: merge piggy.*.S and simplify Makefile
ARM: 8541/1: decompressor: drop redundant FORCE in Makefile
ARM: 8540/1: decompressor: use clean-files instead of extra-y to clean files
ARM: 8539/1: decompressor: drop more unneeded assignments to "targets"
ARM: 8538/1: decompressor: drop unneeded assignments to "targets"
ARM: 8532/1: uncompress: mark putc as inline
ARM: 8531/1: turn init_new_context into an inline function
ARM: 8530/1: remove VIRT_TO_BUS
ARM: 8537/1: drop unused DEBUG_RODATA from XIP_KERNEL
ARM: 8536/1: mm: hide __start_rodata_section_aligned for non-debug builds
ARM: 8535/1: mm: DEBUG_RODATA makes no sense with XIP_KERNEL
ARM: 8534/1: virt: fix hyp-stub build for pre-ARMv7 CPUs
ARM: make the physical-relative calculation more obvious
ARM: 8512/1: proc-v7.S: Adjust stack address when XIP_KERNEL
ARM: 8411/1: Add default SPARSEMEM settings
ARM: 8503/1: clk_register_clkdev: remove format string interface
ARM: 8529/1: remove 'i' and 'zi' targets
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- new tool 'dtx_diff' to diff DT files
- sync kernel's dtc/libfdt to current dtc repo master
- fix for reserved memory regions located in highmem
- document standard unit suffixes for DT properties
- various DT binding doc updates
* tag 'devicetree-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Add vendor prefix for eGalax_eMPIA Technology Inc
Input: ads7846: Add description how to use internal reference (ADS7846)
ARM: realview: add EB syscon variants to bindings
devicetree: bindings: ARM: Use "uV" for micro-volt
serial: fsl-imx-uart: Fix typo in fsl,dte-mode description
of: add 'const' for of_property_*_string*() parameter '*np'
of/unittest: fix infinite loop in of_unittest_destroy_tracked_overlays()
of: alloc anywhere from memblock if range not specified
kbuild: Allow using host dtc instead of kernel's copy
of: resolver: Add missing of_node_get and of_node_put
of: Add United Radiant Technology Corporation vendor prefix
dt/bindings: add documentation on standard property unit suffixes
scripts/dtc: Update to upstream commit b06e55c88b9b
ARM: boot: Add an implementation of strnlen for libfdt
scripts/dtc: dtx_diff - add info to error message
dtc: create tool to diff device trees
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
|
|
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
|
|
This will be needed for UniPhier PH1-LD11 and PH1-LD20 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Just for consistent coding style.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Initial commit for PH1-Pro4 Sanji board support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Initial commit for PH1-Pro4 Ace board support.
Note:
There are two variants for the amount of DDR memory; 1GB or 2GB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is used for on-board inter-connection.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This board has an EEPROM (STMicroelectronics M24C64-WMN6TP) connected
to the I2C channel 0 of the SoC. Its slave address is 0x54.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add master clock nodes generated by crystal oscillators.
PH1-sLD3, PH1-LD4: 24.576 MHz
PH1-Pro4, ProXstream2: 25.000 MHz
PH1-Pro5: 20.000 MHz
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
