| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Only two patches this time, one to fix ethernet probe order on at91
(better fix with proper device aliasing will be done for 3.15, this is
stop-gap), and one update to MAINTAINERS due to Freescale moving their
repo to kernel.org"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: at91: fix network interface ordering for sama5d36
MAINTAINERS: update IMX kernel git tree
|
|
On the newly introduced sama5d36, Gigabit and 10/100 Ethernet network
interfaces are probed in a different order than for the sama5d35.
Moreover, users are accustomed to this order in bootloaders and backports
for older kernel revisions.
So this patch switches DT node order as it is done for the other dual-Ethernet
sama5d3 SoC.
Better interface numbering which does not depend on DT node order is being
developed for stronger interface identification.
Signed-off-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Two omap3430 vs 3630 device tree regression fixes for
issues booting 3430 based boards.
* tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://github.com/broadcom/bcm11351 into fixes
Merge 'bcm pinctrl rename' From Christin Daudt:
Rename pinctrl dt binding to restore consistency with other bcm mobile
bindings.
* tag 'bcm-for-3.14-pinctrl-reduced-rename' of git://github.com/broadcom/bcm11351:
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
+ Linux 3.14-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allwinner fixes from Maxime Ripard:
Two fixes for device trees additions that got added in 3.14. One fixes the
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14
* tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux:
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM fixes from Russell King:
"A number of ARM updates for -rc, covering mostly ARM specific code,
but with one change to modpost.c to allow Thumb section mismatches to
be detected.
ARM changes include reporting when an attempt is made to boot a LPAE
kernel on hardware which does not support LPAE, rather than just being
silent about it.
A number of other minor fixes are included too"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7992/1: boot: compressed: ignore bswapsdi2.S
ARM: 7991/1: sa1100: fix compile problem on Collie
ARM: fix noMMU kallsyms symbol filtering
ARM: 7980/1: kernel: improve error message when LPAE config doesn't match CPU
ARM: 7964/1: Detect section mismatches in thumb relocations
ARM: 7963/1: mm: report both sections from PMD
|
|
Commit 017f161a55b4 (ARM: 7877/1: use built-in byte swap function) added
bswapsdi2.{o,S} to arch/arm/boot/compressed/Makefile, but didn't update
the .gitignore. Thus after a a build git status shows bswapsdi2.S as a
new file, which is a little annoying.
This patch updates arch/arm/boot/compressed/.gitignore to ignore
bswapsdi2.S, as we already do for ashldi3.S and others.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Due to a problem in the MFD Kconfig it was not possible to
compile the UCB battery driver for the Collie SA1100 system,
in turn making it impossible to compile in the battery driver.
(See patch "mfd: include all drivers in subsystem menu".)
After fixing the MFD Kconfig (separate patch) a compile error
appears in the Collie battery driver due to the <mach/collie.h>
implicitly requiring <mach/hardware.h> through <linux/gpio.h>
via <mach/gpio.h> prior to commit
40ca061b "ARM: 7841/1: sa1100: remove complex GPIO interface".
Fix this up by including the required header into
<mach/collie.h>.
Cc: stable@vger.kernel.org
Cc: Andrea Adami <andrea.adami@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
With noMMU, CONFIG_PAGE_OFFSET was not being set correctly. As there's
no MMU, PAGE_OFFSET should be equal to PHYS_OFFSET in all cases. This
commit makes that explicit.
Since we do this, we don't need to mess around in asm/memory.h with
ifdefs to sort this out, so let's get rid of that, and there's no point
offering the "Memory split" option for noMMU as that's meaningless
there.
Fixes: b9b32bf70f2f ("ARM: use linker magic for vectors and vector stubs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from Konrad Rzeszutek Wilk:
"This has exactly one patch for Xen ARM. It sets the dependency to
compile the kernel with MMU enabled - otherwise - the guest won't work
very well"
* tag 'stable/for-linus-3.14-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
ARM: XEN depends on having a MMU
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
There is a single framework fix that prevents dereferencing a NULL
pointer when calling clk_get. The range of fixes for clock driver
regressions spans memory leak fixes, touching the wrong registers that
cause things to explode, misconfigured clock rates that result in
non-responsive devices and even some boot failures. The most benign
fix is DT binding doc typo. It is a stable ABI exposed from the
kernel that was introduced in -rc1, so best to fix it now"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk:at91: Fix memory leak in of_at91_clk_master_setup()
clk: nomadik: fix multiplatform problem
clk: Correct handling of NULL clk in __clk_{get, put}
clk: shmobile: Fix typo in MSTP clock DT bindings
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent for all non-PLL clocks
clk: tegra124: remove gr2d and gr3d clocks
clk: tegra: Fix vic03 mux index
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent all non-PLL clocks
clk: tegra: use max divider if divider overflows
clk: tegra: cclk_lp has a pllx/2 divider
clk: tegra: fix sdmmc clks on Tegra1x4
clk: tegra: fix host1x clock on Tegra124
clk: tegra: PLLD2 fixes for hdmi
clk: tegra: Fix PLLD mnp table
clk: tegra: Fix PLLP rate table
clk: tegra: Correct clock number for UARTE
clk: tegra: Add missing Tegra20 fuse clks
ARM: keystone: dts: fix clkvcp3 control register address
...
|
|
arch/arm/xen/enlighten.c (and maybe others) use MMU-specific functions
like pte_mkspecial which are only available on MMU builds. So let XEN
depend on MMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
problems with booting
Without that change booting leads to crash with more warnings like below:
[ 0.284454] omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
[ 0.284484] omap_hwmod: uart4: cannot _init_clocks
[ 0.284484] ------------[ cut here ]------------
[ 0.284545] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2543 _init+0x300/0x3e4()
[ 0.284545] omap_hwmod: uart4: couldn't init clocks
[ 0.284576] Modules linked in:
[ 0.284606] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-next-20140124-00020-gd2aefec-dirty #26
[ 0.284637] [<c00151c0>] (unwind_backtrace) from [<c0011e20>] (show_stack+0x10/0x14)
[ 0.284667] [<c0011e20>] (show_stack) from [<c0568544>] (dump_stack+0x7c/0x94)
[ 0.284729] [<c0568544>] (dump_stack) from [<c003ff94>] (warn_slowpath_common+0x6c/0x90)
[ 0.284729] [<c003ff94>] (warn_slowpath_common) from [<c003ffe8>] (warn_slowpath_fmt+0x30/0x40)
[ 0.284759] [<c003ffe8>] (warn_slowpath_fmt) from [<c07d1be8>] (_init+0x300/0x3e4)
[ 0.284790] [<c07d1be8>] (_init) from [<c07d217c>] (__omap_hwmod_setup_all+0x40/0x8c)
[ 0.284820] [<c07d217c>] (__omap_hwmod_setup_all) from [<c0008918>] (do_one_initcall+0xe8/0x14c)
[ 0.284851] [<c0008918>] (do_one_initcall) from [<c07c5c18>] (kernel_init_freeable+0x104/0x1c8)
[ 0.284881] [<c07c5c18>] (kernel_init_freeable) from [<c0563524>] (kernel_init+0x8/0x118)
[ 0.284912] [<c0563524>] (kernel_init) from [<c000e368>] (ret_from_fork+0x14/0x2c)
[ 0.285064] ---[ end trace 63de210ad43b627d ]---
Reference:
https://lkml.org/lkml/2013/10/8/553
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The last time tegra_defconfig was rebuilt, various LEDs options were
somehow selected by other options, and hence their entries in
tegra_defconfig were removed by "make savedefconfig". However, for some
reason this is no longer happening, so we need to add the entries back
into tegra_defconfig so the they are enabled in .config.
Fixes: db079b1811d1 ("ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS)"
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull KVM fixes from Paolo Bonzini:
"Three x86 fixes and one for ARM/ARM64.
In particular, nested virtualization on Intel is broken in 3.13 and
fixed by this pull request"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm, vmx: Really fix lazy FPU on nested guest
kvm: x86: fix emulator buffer overflow (CVE-2014-0049)
arm/arm64: KVM: detect CPU reset on CPU_PM_EXIT
KVM: MMU: drop read-only large sptes when creating lower level sptes
|
|
This patch is based on commit:
016c12d2 ("ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree")
and fixes a boot hang due the IGEP board being wrongly initialized
as an OMAP3430 platform instead of an OMAP3630.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes from Tony Lindgren:
Fixes for omaps mostly to fix the 3430 display regression,
and random crashes if booting n900 with device tree and
thumb mode. Also few other regressions and fixes.
* tag 'omap-for-v3.14/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix pinctrl interrupts for core2
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
After splitting padconf core into two parts to avoid exposing
unaccessable registers, the new padconf core2 domain was left
without a wake-up interrupt.
Fix the issue by passing the shared wake-up interrupt in
platform data like we do for padconf core and wkup domains
already.
Fixes: 3d49538364 (ARM: dts: Split omap3 pinmux core device)
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 1fcf7ce0c602 (arm: kvm: implement CPU PM notifier) added
support for CPU power-management, using a cpu_notifier to re-init
KVM on a CPU that entered CPU idle.
The code assumed that a CPU entering idle would actually be powered
off, loosing its state entierely, and would then need to be
reinitialized. It turns out that this is not always the case, and
some HW performs CPU PM without actually killing the core. In this
case, we try to reinitialize KVM while it is still live. It ends up
badly, as reported by Andre Przywara (using a Calxeda Midway):
[ 3.663897] Kernel panic - not syncing: unexpected prefetch abort in Hyp mode at: 0x685760
[ 3.663897] unexpected data abort in Hyp mode at: 0xc067d150
[ 3.663897] unexpected HVC/SVC trap in Hyp mode at: 0xc0901dd0
The trick here is to detect if we've been through a full re-init or
not by looking at HVBAR (VBAR_EL2 on arm64). This involves
implementing the backend for __hyp_get_vectors in the main KVM HYP
code (rather small), and checking the return value against the
default one when the CPU notifier is called on CPU_PM_EXIT.
Reported-by: Andre Przywara <osp@andrep.de>
Tested-by: Andre Przywara <osp@andrep.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <rob.herring@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
into clk-fixes
|
|
This commit updates bcm11351.dtsi with the new compatible string for
the same driver.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
|
|
for non SMP build, NR_CPUS is 1 and hence the code complains with below
warnings.
arch/arm/mach-omap2/cpuidle44xx.c:207:8: warning: array subscript is above array bounds [-Warray-bounds]
arch/arm/mach-omap2/cpuidle44xx.c:212:11: warning: array subscript is above array bounds [-Warray-bounds]
Kill it by making array size fixed.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Without enabling the workaround for ARM errata 430973 thumb
compiled userland crashes randomly on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.14/fixes
Several OMAP clock/PM/device data fixes for v3.14-rc. There's an OMAP5
reboot fix in there, plus a clock fix for rate computations involving
x2 multipliers.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.14-rc/20140219131753/
Note that most full-chip PM is broken since the v3.14 merge; it's
not caused by this series.
|
|
Pull devicetree fixes from Grant Likely:
"Device tree compatible match order bug fix
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of
of_device_ids, but it more than one entry will match, then the device
driver may choose the wrong one. Commit 105353145e, "match each node
compatible against all given matches first", was queued for v3.14 but
ended up causing other bugs. Commit 06b29e76a7 attempted to fix it
but it had other bugs. Merely reverting the fix and waiting until
v3.15 isn't a good option because there is code in v3.14 that depends
on the revised behaviour to boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also
adds new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc
pull, but moving the test case data out of out of arch/arm so that it
could be validated on other architectures was important"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Add self test for of_match_node()
of: Move testcase FDT data into drivers/of
of: reimplement the matching method for __of_match_node()
Revert "of: search the best compatible match first in __of_match_node()"
|
|
Currently, when the kernel is configured with LPAE support, but the
CPU doesn't support it, the error message is fairly cryptic:
Error: unrecognized/unsupported processor variant (0x561f5811).
This messages is normally shown when there is an issue when comparing
the processor ID (CP15 0, c0, c0) with the values/masks described in
proc-v7.S. However, the same message is displayed when LPAE support is
enabled in the kernel configuration, but not available in the CPU,
after looking at ID_MMFR0 (CP15 0, c0, c1, 4). Having the same error
message is highly misleading.
This commit improves this by showing a different error message when
this situation occurs:
Error: Kernel with LPAE support, but CPU does not support LPAE.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Quite a few fixes this time.
Three locking fixes, all marked for -stable. A couple error path
fixes and some misc fixes. Hugh found a bug in memcg offlining
sequence and we thought we could fix that from cgroup core side but
that turned out to be insufficient and got reverted. A different fix
has been applied to -mm"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: update cgroup_enable_task_cg_lists() to grab siglock
Revert "cgroup: use an ordered workqueue for cgroup destruction"
cgroup: protect modifications to cgroup_idr with cgroup_mutex
cgroup: fix locking in cgroup_cfts_commit()
cgroup: fix error return from cgroup_create()
cgroup: fix error return value in cgroup_mount()
cgroup: use an ordered workqueue for cgroup destruction
nfs: include xattr.h from fs/nfs/nfs3proc.c
cpuset: update MAINTAINERS entry
arm, pm, vmpressure: add missing slab.h includes
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"This contains fixes for incorrect atomic test in dma-mapping subsystem
for ARM and x86 architecture"
* 'fixes-for-v3.14' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
x86: dma-mapping: fix GFP_ATOMIC macro usage
ARM: dma-mapping: fix GFP_ATOMIC macro usage
|
|
The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.
Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
If CLK_SET_RATE_PARENT is set for a clkoutx2 clock, calling
clk_set_rate() on the clock "skips" the x2 multiplier as there are no
set_rate and round_rate functions defined for the clkoutx2.
This results in getting double the requested clock rates, breaking the
display on omap3430 based devices. This got broken when
d0f58bd3bba3877fb1af4664c4e33273d36f00e4 and related patches were merged
for v3.14, as omapdss driver now relies more on the clk-framework and
CLK_SET_RATE_PARENT.
This patch implements set_rate and round_rate for clkoutx2.
Tested on OMAP3430, OMAP3630, OMAP4460.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit 313a76e (ARM: OMAP2+: hwmod: Fix SOFTRESET logic) introduced
softreset bit cleaning right after set one. It is caused L3 error for
OMAP4 ISS because ISS register write occurs when ISS reset process is in
progress. Avoid this situation by cleaning softreset bit later, when reset
process is successfully finished.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The spinlock module's SYSCONFIG register on DRA7xx does not
support smart wakeup, and also does not have the CLKACTIVITY
field. The sysc data for spinlock module has been appropriately
fixed up to reflect the same.
Cc: Ambresh K <ambresh@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Use the correct register offset for issuing the
reset command in OMAP5. Since dev_inst is set dynamically
OMAP4 should not be affected by this change.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@gmail.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into clk-fixes
|
|
Fix tegra_init_cache() to check whether the system has a PL310 cache
before touching the PL310 registers. This prevents access to non-existent
registers on Tegra114 and later.
Note for stable kernels:
In <= v3.12, the file to patch is arch/arm/mach-tegra/common.c.
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
fixes
mvebu dt fixes for v3.14
- mvebu: add missing 'eth3' alias for mv78260
- dove: revert PMU interrupt controller node, wait for driver to land.
* tag 'mvebu-dt-fixes-3.14' of git://git.infradead.org/linux-mvebu:
ARM: dove: dt: revert PMU interrupt controller node
ARM: mvebu: dt: add missing alias 'eth3' on Armada XP mv78260
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When building a kernel image with only CONFIG_CPU_IDLE but no CONFIG_PM,
we will get the following link error.
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_enter_wait':
platform-spi_imx.c:(.text+0x25c0): undefined reference to `imx6q_set_lpm'
platform-spi_imx.c:(.text+0x25d4): undefined reference to `imx6q_set_lpm'
arch/arm/mach-imx/built-in.o: In function `imx6q_cpuidle_init':
platform-spi_imx.c:(.init.text+0x75d4): undefined reference to `imx6q_set_chicken_bit'
make[1]: *** [vmlinux] Error 1
Since pm-imx6q.c has been a collection of library functions that access
CCM low-power registers used by not only suspend but also cpuidle and
other drivers, let's build pm-imx6q.c independently of CONFIG_PM to fix
above error.
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@vger.kernel.org
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to deal with the 34xx vs 36xx SoC
configuration for overo boards.
* tag 'omap-for-v3.14/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
ARM: dts: am335x-evmsk: Fix mmc1 support
ARM: DTS: am335x-evmsk: Correct audio clock frequency
ARM: dts: omap3-gta04: Add EOC irq gpio line handling.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.
Fixes: 553c0a200e20 ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into fixes
* tag 'pwm_pxa_for_v3.14' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
ARM: pxa: Add dummy backlight power supply on Mitac Mio A701
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
On 2-level page table systems, the PMD has 2 section entries. Report
these, otherwise ARM_PTDUMP will miss reporting permission changes on
odd section boundaries.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The corresponding driver didn't make it into v3.14, so we need to remove
the node. Dove systems fail to boot with the node present and no
driver.
This node will be re-added when the driver makes it to mainline.
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Add DSB after icache flush to complete the cache maintenance operation.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
|
|
Unfortunatly the device tree for older OMAP35xx Overo cannot be used
with newer OMAP36xx and vice-versa. To address this issue, move most of
the Tobi DTS to a common include file, and create model-specific Tobi
DTS.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Gumstix is the correct vendor for all Overo related products.
Reported-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
