| Age | Commit message (Collapse) | Author |
|---|
|
All 486+ CPUs support WP in supervisor mode, so remove the fallback
386 support code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1354132230-21854-7-git-send-email-hpa@linux.intel.com
|
|
All 486+ CPUs support INVLPG, so remove the fallback 386 support
code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1354132230-21854-6-git-send-email-hpa@linux.intel.com
|
|
commit 611ae8e3f5204f7480b3b405993b3352cfa16662('enable tlb flush range
support for x86') change flush_tlb_mm_range() considerably. After this,
we test whether vmflag equal to VM_HUGETLB and it may be always failed,
because vmflag usually has other flags simultaneously.
Our intention is to check whether this vma is for hughtlb, so correct it
according to this purpose.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Acked-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1352740656-19417-1-git-send-email-js1304@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Commit
844ab6f9 x86, mm: Find_early_table_space based on ranges that are actually being mapped
added back some lines back wrongly that has been removed in commit
7b16bbf97 Revert "x86/mm: Fix the size calculation of mapping tables"
remove them again.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQW_vuaYQbmagVnxT2DGsYc=9tNeAbdBq53sYkitPOwxSQ@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Current logic finds enough space for direct mapping page tables from 0
to end. Instead, we only need to find enough space to cover mr[0].start
to mr[nr_range].end -- the range that is actually being mapped by
init_memory_mapping()
This is needed after 1bbbbe779aabe1f0768c2bf8f8c0a5583679b54a, to address
the panic reported here:
https://lkml.org/lkml/2012/10/20/160
https://lkml.org/lkml/2012/10/21/157
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Link: http://lkml.kernel.org/r/20121024195311.GB11779@jshin-Toonie
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Commit 20167d3421a089a1bf1bd680b150dc69c9506810 ("x86-64: Fix
accounting in kernel_physical_mapping_init()") went a little too
far by entirely removing the counting of pre-populated page
tables: this should be done at boot time (to cover the page
tables set up in early boot code), but shouldn't be done during
memory hot add.
Hence, re-add the removed increments of "pages", but make them
and the one in phys_pte_init() conditional upon !after_bootmem.
Reported-Acked-and-Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/506DAFBA020000780009FA8C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
722bc6b16771 x86/mm: Fix the size calculation of mapping tables
Tried to address the issue that the first 2/4M should use 4k pages
if PSE enabled, but extra counts should only be valid for x86_32.
This commit caused a kdump regression: the kdump kernel hangs.
Work is in progress to fundamentally fix the various page table
initialization issues that we have, via the design suggested
by H. Peter Anvin, but it's not ready yet to be merged.
So, to get a working kdump revert to the last known working version,
which is the revert of this commit and of a followup fix (which was
incomplete):
bd2753b2dda7 x86/mm: Only add extra pages count for the first memory range during pre-allocation
Tested kdump on physical and virtual machines.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Tested-by: Flavio Leitner <fbl@redhat.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Flavio Leitner <fbl@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: ianfang.cn@gmail.com
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Provide rb_insert_augmented() and rb_erase_augmented() through a new
rbtree_augmented.h include file. rb_erase_augmented() is defined there as
an __always_inline function, in order to allow inlining of augmented
rbtree callbacks into it. Since this generates a relatively large
function, each augmented rbtree user should make sure to have a single
call site.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement an interval tree as a replacement for the VMA prio_tree. The
algorithms are similar to lib/interval_tree.c; however that code can't be
directly reused as the interval endpoints are not explicitly stored in the
VMA. So instead, the common algorithm is moved into a template and the
details (node type, how to get interval endpoints from the node, etc) are
filled in using the C preprocessor.
Once the interval tree functions are available, using them as a
replacement to the VMA prio tree is a relatively simple, mechanical job.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As proposed by Peter Zijlstra, this makes it easier to define the augmented
rbtree callbacks.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
convert arch/x86/mm/pat_rbtree.c to the proposed augmented rbtree api
and remove the old augmented rbtree implementation.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the generic vma-flag VM_PFN_AT_MMAP with x86-only VM_PAT.
We can toss mapping address from remap_pfn_range() into
track_pfn_vma_new(), and collect all PAT-related logic together in
arch/x86/.
This patch also restores orignal frustration-free is_cow_mapping() check
in remap_pfn_range(), as it was before commit v2.6.28-rc8-88-g3c8bb73
("x86: PAT: store vm_pgoff for all linear_over_vma_region mappings - v3")
is_linear_pfn_mapping() checks can be removed from mm/huge_memory.c,
because it already handled by VM_PFNMAP in VM_NO_THP bit-mask.
[suresh.b.siddha@intel.com: Reset the VM_PAT flag as part of untrack_pfn_vma()]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
vm_insert_pfn
With PAT enabled, vm_insert_pfn() looks up the existing pfn memory
attribute and uses it. Expectation is that the driver reserves the
memory attributes for the pfn before calling vm_insert_pfn().
remap_pfn_range() (when called for the whole vma) will setup a new
attribute (based on the prot argument) for the specified pfn range.
This addresses the legacy usage which typically calls remap_pfn_range()
with a desired memory attribute. For ranges smaller than the vma size
(which is typically not the case), remap_pfn_range() will use the
existing memory attribute for the pfn range.
Expose two different API's for these different behaviors.
track_pfn_insert() for tracking the pfn attribute set by vm_insert_pfn()
and track_pfn_remap() for the remap_pfn_range().
This cleanup also prepares the ground for the track/untrack pfn vma
routines to take over the ownership of setting PAT specific vm_flag in
the 'vma'.
[khlebnikov@openvz.org: Clear checks in track_pfn_remap()]
[akpm@linux-foundation.org: tweak a few comments]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'pfn' argument for track_pfn_vma_new() can be used for reserving the
attribute for the pfn range. No need to depend on 'vm_pgoff'
Similarly, untrack_pfn_vma() can depend on the 'pfn' argument if it is
non-zero or can use follow_phys() to get the starting value of the pfn
range.
Also the non zero 'size' argument can be used instead of recomputing it
from vma.
This cleanup also prepares the ground for the track/untrack pfn vma
routines to take over the ownership of setting PAT specific vm_flag in the
'vma'.
[khlebnikov@openvz.org: Clear pfn to paddr conversion]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/smap support from Ingo Molnar:
"This adds support for the SMAP (Supervisor Mode Access Prevention) CPU
feature on Intel CPUs: a hardware feature that prevents unintended
user-space data access from kernel privileged code.
It's turned on automatically when possible.
This, in combination with SMEP, makes it even harder to exploit kernel
bugs such as NULL pointer dereferences."
Fix up trivial conflict in arch/x86/kernel/entry_64.S due to newly added
includes right next to each other.
* 'x86-smap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, smep, smap: Make the switching functions one-way
x86, suspend: On wakeup always initialize cr4 and EFER
x86-32: Start out eflags and cr4 clean
x86, smap: Do not abuse the [f][x]rstor_checking() functions for user space
x86-32, smap: Add STAC/CLAC instructions to 32-bit kernel entry
x86, smap: Reduce the SMAP overhead for signal handling
x86, smap: A page fault due to SMAP is an oops
x86, smap: Turn on Supervisor Mode Access Prevention
x86, smap: Add STAC and CLAC instructions to control user space access
x86, uaccess: Merge prototypes for clear_user/__clear_user
x86, smap: Add a header file with macros for STAC/CLAC
x86, alternative: Add header guards to <asm/alternative-asm.h>
x86, alternative: Use .pushsection/.popsection
x86, smap: Add CR4 bit for SMAP
x86-32, mm: The WP test should be done on a kernel page
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/platform changes from Ingo Molnar:
"This cleans up some Xen-induced pagetable init code uglies, by
generalizing new platform callbacks and state: x86_init.paging.*"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Document x86_init.paging.pagetable_init()
x86: xen: Cleanup and remove x86_init.paging.pagetable_setup_done()
x86: Move paging_init() call to x86_init.paging.pagetable_init()
x86: Rename pagetable_setup_start() to pagetable_init()
x86: Remove base argument from x86_init.paging.pagetable_setup_start
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/mm changes from Ingo Molnar:
"The biggest change is new TLB partial flushing code for AMD CPUs.
(The v3.6 kernel had the Intel CPU side code, see commits
e0ba94f14f74..effee4b9b3b.)
There's also various other refinements around the TLB flush code"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Distinguish TLB shootdown interrupts from other functions call interrupts
x86/mm: Fix range check in tlbflush debugfs interface
x86, cpu: Preset default tlb_flushall_shift on AMD
x86, cpu: Add AMD TLB size detection
x86, cpu: Push TLB detection CPUID check down
x86, cpu: Fixup tlb_flushall_shift formatting
|
|
As TLB shootdown requests to other CPU cores are now using function call
interrupts, TLB shootdowns entry in /proc/interrupts is always shown as 0.
This behavior change was introduced by commit 52aec3308db8 ("x86/tlb:
replace INVALIDATE_TLB_VECTOR by CALL_FUNCTION_VECTOR").
This patch reverts TLB shootdowns entry in /proc/interrupts to count TLB
shootdowns separately from the other function call interrupts.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Link: http://lkml.kernel.org/r/20120926021128.22212.20440.stgit@hpxw
Acked-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Add necessary hooks to x86 exception for userspace
RCU extended quiescent state support.
This includes traps, page fault, debug exceptions, etc...
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
If we get a page fault due to SMAP, trigger an oops rather than
spinning forever.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348256595-29119-11-git-send-email-hpa@linux.intel.com
|
|
PAGE_READONLY includes user permission, but this is a page used
exclusively by the kernel; use PAGE_KERNEL_RO instead.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348256595-29119-3-git-send-email-hpa@linux.intel.com
|
|
Fixing an off-by-one error in devmem_is_allowed(), which allows
accesses to physical addresses 0x100000-0x100fff, an extra page
past 1MB.
Signed-off-by: T Makphaibulchoke <tmac@hp.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: yinghai@kernel.org
Cc: tiwai@suse.de
Cc: dhowells@redhat.com
Link: http://lkml.kernel.org/r/1346210503-14276-1-git-send-email-tmac@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
At this stage x86_init.paging.pagetable_setup_done is only used in the
XEN case. Move its content in the x86_init.paging.pagetable_init setup
function and remove the now unused x86_init.paging.pagetable_setup_done
remaining infrastructure.
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Acked-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-5-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Move the paging_init() call to the platform specific pagetable_init()
function, so we can get rid of the extra pagetable_setup_done()
function pointer.
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Acked-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-4-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In preparation for unifying the pagetable_setup_start() and
pagetable_setup_done() setup functions, rename appropriately all the
infrastructure related to pagetable_setup_start().
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Ackedd-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-3-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We either use swapper_pg_dir or the argument is unused. Preparatory
patch to simplify platform pagetable setup further.
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Ackedb-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-2-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Since the shift count settable there is used for shifting values
of type "unsigned long", its value must not match or exceed
BITS_PER_LONG (otherwise the shift operations are undefined).
Similarly, the value must not be negative (but -1 must be
permitted, as that's the value used to distinguish the case of
the fine grained flushing being disabled).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/5049B65C020000780009990C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Each page mapped in a process's address space must be correctly
accounted for in _mapcount. Normally the rules for this are
straightforward but hugetlbfs page table sharing is different. The page
table pages at the PMD level are reference counted while the mapcount
remains the same.
If this accounting is wrong, it causes bugs like this one reported by
Larry Woodman:
kernel BUG at mm/filemap.c:135!
invalid opcode: 0000 [#1] SMP
CPU 22
Modules linked in: bridge stp llc sunrpc binfmt_misc dcdbas microcode pcspkr acpi_pad acpi]
Pid: 18001, comm: mpitest Tainted: G W 3.3.0+ #4 Dell Inc. PowerEdge R620/07NDJ2
RIP: 0010:[<ffffffff8112cfed>] [<ffffffff8112cfed>] __delete_from_page_cache+0x15d/0x170
Process mpitest (pid: 18001, threadinfo ffff880428972000, task ffff880428b5cc20)
Call Trace:
delete_from_page_cache+0x40/0x80
truncate_hugepages+0x115/0x1f0
hugetlbfs_evict_inode+0x18/0x30
evict+0x9f/0x1b0
iput_final+0xe3/0x1e0
iput+0x3e/0x50
d_kill+0xf8/0x110
dput+0xe2/0x1b0
__fput+0x162/0x240
During fork(), copy_hugetlb_page_range() detects if huge_pte_alloc()
shared page tables with the check dst_pte == src_pte. The logic is if
the PMD page is the same, they must be shared. This assumes that the
sharing is between the parent and child. However, if the sharing is
with a different process entirely then this check fails as in this
diagram:
parent
|
------------>pmd
src_pte----------> data page
^
other--------->pmd--------------------|
^
child-----------|
dst_pte
For this situation to occur, it must be possible for Parent and Other to
have faulted and failed to share page tables with each other. This is
possible due to the following style of race.
PROC A PROC B
copy_hugetlb_page_range copy_hugetlb_page_range
src_pte == huge_pte_offset src_pte == huge_pte_offset
!src_pte so no sharing !src_pte so no sharing
(time passes)
hugetlb_fault hugetlb_fault
huge_pte_alloc huge_pte_alloc
huge_pmd_share huge_pmd_share
LOCK(i_mmap_mutex)
find nothing, no sharing
UNLOCK(i_mmap_mutex)
LOCK(i_mmap_mutex)
find nothing, no sharing
UNLOCK(i_mmap_mutex)
pmd_alloc pmd_alloc
LOCK(instantiation_mutex)
fault
UNLOCK(instantiation_mutex)
LOCK(instantiation_mutex)
fault
UNLOCK(instantiation_mutex)
These two processes are not poing to the same data page but are not
sharing page tables because the opportunity was missed. When either
process later forks, the src_pte == dst pte is potentially insufficient.
As the check falls through, the wrong PTE information is copied in
(harmless but wrong) and the mapcount is bumped for a page mapped by a
shared page table leading to the BUG_ON.
This patch addresses the issue by moving pmd_alloc into huge_pmd_share
which guarantees that the shared pud is populated in the same critical
section as pmd. This also means that huge_pte_offset test in
huge_pmd_share is serialized correctly now which in turn means that the
success of the sharing will be higher as the racing tasks see the pud
and pmd populated together.
Race identified and changelog written mostly by Mel Gorman.
{akpm@linux-foundation.org: attempt to make the huge_pmd_share() comment comprehensible, clean up coding style]
Reported-by: Larry Woodman <lwoodman@redhat.com>
Tested-by: Larry Woodman <lwoodman@redhat.com>
Reviewed-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Ken Chen <kenchen@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit bacef661acdb634170a8faddbc1cf28e8f8b9eee.
This commit has been found to cause serious regressions on a number of
ASUS machines at the least. We probably need to provide a 1:1 map in
addition to the EFI virtual memory map in order for this to work.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reported-and-bisected-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120805172903.5f8bb24c@zougloub.eu
|
|
Otherwise you could run into:
WARN_ON in numa_register_memblks(), because node_possible_map is zero
References: https://bugzilla.novell.com/show_bug.cgi?id=757888
On this machine (ProLiant ML570 G3) the SRAT table contains:
- No processor affinities
- One memory affinity structure (which is set disabled)
CC: Per Jessen <per@opensuse.org>
CC: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/mm changes from Peter Anvin:
"The big change here is the patchset by Alex Shi to use INVLPG to flush
only the affected pages when we only need to flush a small page range.
It also removes the special INVALIDATE_TLB_VECTOR interrupts (32
vectors!) and replace it with an ordinary IPI function call."
Fix up trivial conflicts in arch/x86/include/asm/apic.h (added code next
to changed line)
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tlb: Fix build warning and crash when building for !SMP
x86/tlb: do flush_tlb_kernel_range by 'invlpg'
x86/tlb: replace INVALIDATE_TLB_VECTOR by CALL_FUNCTION_VECTOR
x86/tlb: enable tlb flush range support for x86
mm/mmu_gather: enable tlb flush range in generic mmu_gather
x86/tlb: add tlb_flushall_shift knob into debugfs
x86/tlb: add tlb_flushall_shift for specific CPU
x86/tlb: fall back to flush all when meet a THP large page
x86/flush_tlb: try flush_tlb_single one by one in flush_tlb_range
x86/tlb_info: get last level TLB entry number of CPU
x86: Add read_mostly declaration/definition to variables from smp.h
x86: Define early read-mostly per-cpu macros
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pul x86/efi changes from Ingo Molnar:
"This tree adds an EFI bootloader handover protocol, which, once
supported on the bootloader side, will make bootup faster and might
result in simpler bootloaders.
The other change activates the EFI wall clock time accessors on x86-64
as well, instead of the legacy RTC readout."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Handover Protocol
x86-64/efi: Use EFI to deal with platform wall clock
|
|
This patch do flush_tlb_kernel_range by 'invlpg'. The performance pay
and gain was analyzed in previous patch
(x86/flush_tlb: try flush_tlb_single one by one in flush_tlb_range).
In the testing: http://lkml.org/lkml/2012/6/21/10
The pay is mostly covered by long kernel path, but the gain is still
quite clear, memory access in user APP can increase 30+% when kernel
execute this funtion.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-10-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
There are 32 INVALIDATE_TLB_VECTOR now in kernel. That is quite big
amount of vector in IDT. But it is still not enough, since modern x86
sever has more cpu number. That still causes heavy lock contention
in TLB flushing.
The patch using generic smp call function to replace it. That saved 32
vector number in IDT, and resolved the lock contention in TLB
flushing on large system.
In the NHM EX machine 4P * 8cores * HT = 64 CPUs, hackbench pthread
has 3% performance increase.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-9-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Not every tlb_flush execution moment is really need to evacuate all
TLB entries, like in munmap, just few 'invlpg' is better for whole
process performance, since it leaves most of TLB entries for later
accessing.
This patch also rewrite flush_tlb_range for 2 purposes:
1, split it out to get flush_blt_mm_range function.
2, clean up to reduce line breaking, thanks for Borislav's input.
My micro benchmark 'mummap' http://lkml.org/lkml/2012/5/17/59
show that the random memory access on other CPU has 0~50% speed up
on a 2P * 4cores * HT NHM EP while do 'munmap'.
Thanks Yongjie's testing on this patch:
-------------
I used Linux 3.4-RC6 w/ and w/o his patches as Xen dom0 and guest
kernel.
After running two benchmarks in Xen HVM guest, I found his patches
brought about 1%~3% performance gain in 'kernel build' and 'netperf'
testing, though the performance gain was not very stable in 'kernel
build' testing.
Some detailed testing results are below.
Testing Environment:
Hardware: Romley-EP platform
Xen version: latest upstream
Linux kernel: 3.4-RC6
Guest vCPU number: 8
NIC: Intel 82599 (10GB bandwidth)
In 'kernel build' testing in guest:
Command line | performance gain
make -j 4 | 3.81%
make -j 8 | 0.37%
make -j 16 | -0.52%
In 'netperf' testing, we tested TCP_STREAM with default socket size
16384 byte as large packet and 64 byte as small packet.
I used several clients to add networking pressure, then 'netperf' server
automatically generated several threads to response them.
I also used large-size packet and small-size packet in the testing.
Packet size | Thread number | performance gain
16384 bytes | 4 | 0.02%
16384 bytes | 8 | 2.21%
16384 bytes | 16 | 2.04%
64 bytes | 4 | 1.07%
64 bytes | 8 | 3.31%
64 bytes | 16 | 0.71%
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-8-git-send-email-alex.shi@intel.com
Tested-by: Ren, Yongjie <yongjie.ren@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
kernel will replace cr3 rewrite with invlpg when
tlb_flush_entries <= active_tlb_entries / 2^tlb_flushall_factor
if tlb_flushall_factor is -1, kernel won't do this replacement.
User can modify its value according to specific CPU/applications.
Thanks for Borislav providing the help message of
CONFIG_DEBUG_TLBFLUSH.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-6-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Testing show different CPU type(micro architectures and NUMA mode) has
different balance points between the TLB flush all and multiple invlpg.
And there also has cases the tlb flush change has no any help.
This patch give a interface to let x86 vendor developers have a chance
to set different shift for different CPU type.
like some machine in my hands, balance points is 16 entries on
Romely-EP; while it is at 8 entries on Bloomfield NHM-EP; and is 256 on
IVB mobile CPU. but on model 15 core2 Xeon using invlpg has nothing
help.
For untested machine, do a conservative optimization, same as NHM CPU.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-5-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
We don't need to flush large pages by PAGE_SIZE step, that just waste
time. and actually, large page don't need 'invlpg' optimizing according
to our micro benchmark. So, just flush whole TLB is enough for them.
The following result is tested on a 2CPU * 4cores * 2HT NHM EP machine,
with THP 'always' setting.
Multi-thread testing, '-t' paramter is thread number:
without this patch with this patch
./mprotect -t 1 14ns 13ns
./mprotect -t 2 13ns 13ns
./mprotect -t 4 12ns 11ns
./mprotect -t 8 14ns 10ns
./mprotect -t 16 28ns 28ns
./mprotect -t 32 54ns 52ns
./mprotect -t 128 200ns 200ns
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-4-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
x86 has no flush_tlb_range support in instruction level. Currently the
flush_tlb_range just implemented by flushing all page table. That is not
the best solution for all scenarios. In fact, if we just use 'invlpg' to
flush few lines from TLB, we can get the performance gain from later
remain TLB lines accessing.
But the 'invlpg' instruction costs much of time. Its execution time can
compete with cr3 rewriting, and even a bit more on SNB CPU.
So, on a 512 4KB TLB entries CPU, the balance points is at:
(512 - X) * 100ns(assumed TLB refill cost) =
X(TLB flush entries) * 100ns(assumed invlpg cost)
Here, X is 256, that is 1/2 of 512 entries.
But with the mysterious CPU pre-fetcher and page miss handler Unit, the
assumed TLB refill cost is far lower then 100ns in sequential access. And
2 HT siblings in one core makes the memory access more faster if they are
accessing the same memory. So, in the patch, I just do the change when
the target entries is less than 1/16 of whole active tlb entries.
Actually, I have no data support for the percentage '1/16', so any
suggestions are welcomed.
As to hugetlb, guess due to smaller page table, and smaller active TLB
entries, I didn't see benefit via my benchmark, so no optimizing now.
My micro benchmark show in ideal scenarios, the performance improves 70
percent in reading. And in worst scenario, the reading/writing
performance is similar with unpatched 3.4-rc4 kernel.
Here is the reading data on my 2P * 4cores *HT NHM EP machine, with THP
'always':
multi thread testing, '-t' paramter is thread number:
with patch unpatched 3.4-rc4
./mprotect -t 1 14ns 24ns
./mprotect -t 2 13ns 22ns
./mprotect -t 4 12ns 19ns
./mprotect -t 8 14ns 16ns
./mprotect -t 16 28ns 26ns
./mprotect -t 32 54ns 51ns
./mprotect -t 128 200ns 199ns
Single process with sequencial flushing and memory accessing:
with patch unpatched 3.4-rc4
./mprotect 7ns 11ns
./mprotect -p 4096 -l 8 -n 10240
21ns 21ns
[ hpa: http://lkml.kernel.org/r/1B4B44D9196EFF41AE41FDA404FC0A100BFF94@SHSMSX101.ccr.corp.intel.com
has additional performance numbers. ]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-3-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
... matching various other architectures.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4FDF1F5C020000780008A661@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix kernel-doc warnings in arch/x86/mm/ioremap.c and
arch/x86/mm/pageattr.c, just like this one:
Warning(arch/x86/mm/ioremap.c:204):
No description found for parameter 'phys_addr'
Warning(arch/x86/mm/ioremap.c:204):
Excess function parameter 'offset' description in 'ioremap_nocache'
Signed-off-by: Wanpeng Li <liwp@linux.vnet.ibm.com>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Wanpeng Li <liwp.linux@gmail.com>
Link: http://lkml.kernel.org/r/1339296652-2935-1-git-send-email-liwp.linux@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
pre-allocation early page table space
Robin found this regression:
| I just tried to boot an 8TB system. It fails very early in boot with:
| Kernel panic - not syncing: Cannot find space for the kernel page tables
git bisect commit 722bc6b16771ed80871e1fd81c86d3627dda2ac8.
A git revert of that commit does boot past that point on the 8TB
configuration.
That commit will add up extra pages for all memory range even
above 4g.
Try to limit that extra page count adding to first entry only.
Bisected-by: Robin Holt <holt@sgi.com>
Tested-by: Robin Holt <holt@sgi.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/CAE9FiQUj3wyzQxtq9yzBNc9u220p8JZ1FYHG7t%3DMOzJ%3D9BZMYA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When hot-adding a CPU, the system outputs following messages
since node_to_cpumask_map[2] was not allocated memory.
Booting Node 2 Processor 32 APIC 0xc0
node_to_cpumask_map[2] NULL
Pid: 0, comm: swapper/32 Tainted: G A 3.3.5-acd #21
Call Trace:
[<ffffffff81048845>] debug_cpumask_set_cpu+0x155/0x160
[<ffffffff8105e28a>] ? add_timer_on+0xaa/0x120
[<ffffffff8150665f>] numa_add_cpu+0x1e/0x22
[<ffffffff815020bb>] identify_cpu+0x1df/0x1e4
[<ffffffff815020d6>] identify_econdary_cpu+0x16/0x1d
[<ffffffff81504614>] smp_store_cpu_info+0x3c/0x3e
[<ffffffff81505263>] smp_callin+0x139/0x1be
[<ffffffff815052fb>] start_secondary+0x13/0xeb
The reason is that the bit of node 2 was not set at
numa_nodes_parsed. numa_nodes_parsed is set by only
acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init. Thus even if hot-added memory
which is same PXM as hot-added CPU is written in ACPI SRAT
Table, if the hot-added CPU is not written in ACPI SRAT table,
numa_nodes_parsed is not set.
But according to ACPI Spec Rev 5.0, it says about ACPI SRAT
table as follows: This optional table provides information that
allows OSPM to associate processors and memory ranges, including
ranges of memory provided by hot-added memory devices, with
system localities / proximity domains and clock domains.
It means that ACPI SRAT table only provides information for CPUs
present at boot time and for memory including hot-added memory.
So hot-added memory is written in ACPI SRAT table, but hot-added
CPU is not written in it. Thus numa_nodes_parsed should be set
by not only acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init but also
acpi_numa_memory_affinity_init for the case.
Additionally, if system has cpuless memory node,
acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init cannot set numa_nodes_parseds
since these functions cannot find cpu description for the node.
In this case, numa_nodes_parsed needs to be set by
acpi_numa_memory_affinity_init.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: liuj97@gmail.com
Cc: kosaki.motohiro@gmail.com
Link: http://lkml.kernel.org/r/4FCC2098.4030007@jp.fujitsu.com
[ merged it ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.
Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).
Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).
Also make the two EFI functions in question here static -
they're not being referenced elsewhere.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4FBFBF5F020000780008637F@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
x86/trampoline contains an urgent commit which is necessarily on a
newer baseline.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Function pat_pagerange_is_ram() scales poorly to large address
ranges, because it probes the resource tree for each page.
On a 2.6 GHz Opteron, this function consumes 34 ms for a 1 GB range.
It is called twice during untrack_pfn_vma(), slowing process
cleanup and handicapping the OOM killer.
This replacement consumes less than 1ms, under the same conditions.
Signed-off-by: John Dykstra <jdykstra@cray.com> on behalf of Cray Inc.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337980366.1979.6.camel@redwood
[ Small stylistic cleanups and renames ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Print physical address info in a style consistent with the %pR style used
elsewhere in the kernel. For example:
-found SMP MP-table at [ffff8800000fce90] fce90
+found SMP MP-table at [mem 0x000fce90-0x000fce9f] mapped at [ffff8800000fce90]
-initial memory mapped : 0 - 20000000
+initial memory mapped: [mem 0x00000000-0x1fffffff]
-Base memory trampoline at [ffff88000009c000] 9c000 size 8192
+Base memory trampoline [mem 0x0009c000-0x0009dfff] mapped at [ffff88000009c000]
-SRAT: Node 0 PXM 0 0-80000000
+SRAT: Node 0 PXM 0 [mem 0x00000000-0x7fffffff]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm changes from Ingo Molnar:
"This tree includes a micro-optimization that avoids cr3 switches
during idling; it fixes corner cases and there's also small cleanups"
Fix up trivial context conflict with the percpu_xx -> this_cpu_xx
changes.
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix accounting in kernel_physical_mapping_init()
x86/tlb: Clean up and unify TLB_FLUSH_ALL definition
x86: Drop obsolete ARCH_BOOTMEM support
x86, tlb: Switch cr3 in leave_mm() only when needed
x86/mm: Fix the size calculation of mapping tables
|
