| Age | Commit message (Collapse) | Author |
|---|
|
On Intel hardware, native_play_dead() uses mwait_play_dead() by
default and only falls back to the other methods if that fails.
That also happens during resume from hibernation, when the restore
(boot) kernel runs disable_nonboot_cpus() to take all of the CPUs
except for the boot one offline.
However, that is problematic, because the address passed to
__monitor() in mwait_play_dead() is likely to be written to in the
last phase of hibernate image restoration and that causes the "dead"
CPU to start executing instructions again. Unfortunately, the page
containing the address in that CPU's instruction pointer may not be
valid any more at that point.
First, that page may have been overwritten with image kernel memory
contents already, so the instructions the CPU attempts to execute may
simply be invalid. Second, the page tables previously used by that
CPU may have been overwritten by image kernel memory contents, so the
address in its instruction pointer is impossible to resolve then.
A report from Varun Koyyalagunta and investigation carried out by
Chen Yu show that the latter sometimes happens in practice.
To prevent it from happening, temporarily change the smp_ops.play_dead
pointer during resume from hibernation so that it points to a special
"play dead" routine which uses hlt_play_dead() and avoids the
inadvertent "revivals" of "dead" CPUs this way.
A slightly unpleasant consequence of this change is that if the
system is hibernated with one or more CPUs offline, it will generally
draw more power after resume than it did before hibernation, because
the physical state entered by CPUs via hlt_play_dead() is higher-power
than the mwait_play_dead() one in the majority of cases. It is
possible to work around this, but it is unclear how much of a problem
that's going to be in practice, so the workaround will be implemented
later if it turns out to be necessary.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106371
Reported-by: Varun Koyyalagunta <cpudebug@centtech.com>
Original-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
|
|
Logan Gunthorpe reports that hibernation stopped working reliably for
him after commit ab76f7b4ab23 (x86/mm: Set NX on gap between __ex_table
and rodata).
That turns out to be a consequence of a long-standing issue with the
64-bit image restoration code on x86, which is that the temporary
page tables set up by it to avoid page tables corruption when the
last bits of the image kernel's memory contents are copied into
their original page frames re-use the boot kernel's text mapping,
but that mapping may very well get corrupted just like any other
part of the page tables. Of course, if that happens, the final
jump to the image kernel's entry point will go to nowhere.
The exact reason why commit ab76f7b4ab23 matters here is that it
sometimes causes a PMD of a large page to be split into PTEs
that are allocated dynamically and get corrupted during image
restoration as described above.
To fix that issue note that the code copying the last bits of the
image kernel's memory contents to the page frames occupied by them
previoulsy doesn't use the kernel text mapping, because it runs from
a special page covered by the identity mapping set up for that code
from scratch. Hence, the kernel text mapping is only needed before
that code starts to run and then it will only be used just for the
final jump to the image kernel's entry point.
Accordingly, the temporary page tables set up in swsusp_arch_resume()
on x86-64 need to contain the kernel text mapping too. That mapping
is only going to be used for the final jump to the image kernel, so
it only needs to cover the image kernel's entry point, because the
first thing the image kernel does after getting control back is to
switch over to its own original page tables. Moreover, the virtual
address of the image kernel's entry point in that mapping has to be
the same as the one mapped by the image kernel's page tables.
With that in mind, modify the x86-64's arch_hibernation_header_save()
and arch_hibernation_header_restore() routines to pass the physical
address of the image kernel's entry point (in addition to its virtual
address) to the boot kernel (a small piece of assembly code involved
in passing the entry point's virtual address to the image kernel is
not necessary any more after that, so drop it). Update RESTORE_MAGIC
too to reflect the image header format change.
Next, in set_up_temporary_mappings(), use the physical and virtual
addresses of the image kernel's entry point passed in the image
header to set up a minimum kernel text mapping (using memory pages
that won't be overwritten by the image kernel's memory contents) that
will map those addresses to each other as appropriate.
This makes the concern about the possible corruption of the original
boot kernel text mapping go away and if the the minimum kernel text
mapping used for the final jump marks the image kernel's entry point
memory as executable, the jump to it is guaraneed to succeed.
Fixes: ab76f7b4ab23 (x86/mm: Set NX on gap between __ex_table and rodata)
Link: http://marc.info/?l=linux-pm&m=146372852823760&w=2
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 kprobe fix from Thomas Gleixner:
"A single fix clearing the TF bit when a fault is single stepped"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes/x86: Clear TF bit in fault on single-stepping
|
|
Merge misc fixes from Andrew Morton:
"Two weeks worth of fixes here"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (41 commits)
init/main.c: fix initcall_blacklisted on ia64, ppc64 and parisc64
autofs: don't get stuck in a loop if vfs_write() returns an error
mm/page_owner: avoid null pointer dereference
tools/vm/slabinfo: fix spelling mistake: "Ocurrences" -> "Occurrences"
fs/nilfs2: fix potential underflow in call to crc32_le
oom, suspend: fix oom_reaper vs. oom_killer_disable race
ocfs2: disable BUG assertions in reading blocks
mm, compaction: abort free scanner if split fails
mm: prevent KASAN false positives in kmemleak
mm/hugetlb: clear compound_mapcount when freeing gigantic pages
mm/swap.c: flush lru pvecs on compound page arrival
memcg: css_alloc should return an ERR_PTR value on error
memcg: mem_cgroup_migrate() may be called with irq disabled
hugetlb: fix nr_pmds accounting with shared page tables
Revert "mm: disable fault around on emulated access bit architecture"
Revert "mm: make faultaround produce old ptes"
mailmap: add Boris Brezillon's email
mailmap: add Antoine Tenart's email
mm, sl[au]b: add __GFP_ATOMIC to the GFP reclaim mask
mm: mempool: kasan: don't poot mempool objects in quarantine
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix x86 PV dom0 crash during early boot on some hardware
- fix two pciback bugs affects certain devices
- fix potential overflow when clearing page tables in x86 PV
* tag 'for-linus-4.7b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-pciback: return proper values during BAR sizing
x86/xen: avoid m2p lookup when setting early page table entries
xen/pciback: Fix conf_space read/write overlap check.
x86/xen: fix upper bound of pmd loop in xen_cleanhighmap()
xen/balloon: Fix declared-but-not-defined warning
|
|
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
efi_alloc_page_tables uses __GFP_REPEAT but it allocates an order-0
page. This means that this flag has never been actually useful here
because it has always been used only for PAGE_ALLOC_COSTLY requests.
Link: http://lkml.kernel.org/r/1464599699-30131-4-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
PGALLOC_GFP uses __GFP_REPEAT but none of the allocation which uses this
flag is for more than order-0. This means that this flag has never been
actually useful here because it has always been used only for
PAGE_ALLOC_COSTLY requests.
Link: http://lkml.kernel.org/r/1464599699-30131-3-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the third version of the patchset previously sent [1]. I have
basically only rebased it on top of 4.7-rc1 tree and dropped "dm: get
rid of superfluous gfp flags" which went through dm tree. I am sending
it now because it is tree wide and chances for conflicts are reduced
considerably when we want to target rc2. I plan to send the next step
and rename the flag and move to a better semantic later during this
release cycle so we will have a new semantic ready for 4.8 merge window
hopefully.
Motivation:
While working on something unrelated I've checked the current usage of
__GFP_REPEAT in the tree. It seems that a majority of the usage is and
always has been bogus because __GFP_REPEAT has always been about costly
high order allocations while we are using it for order-0 or very small
orders very often. It seems that a big pile of them is just a
copy&paste when a code has been adopted from one arch to another.
I think it makes some sense to get rid of them because they are just
making the semantic more unclear. Please note that GFP_REPEAT is
documented as
* __GFP_REPEAT: Try hard to allocate the memory, but the allocation attempt
* _might_ fail. This depends upon the particular VM implementation.
while !costly requests have basically nofail semantic. So one could
reasonably expect that order-0 request with __GFP_REPEAT will not loop
for ever. This is not implemented right now though.
I would like to move on with __GFP_REPEAT and define a better semantic
for it.
$ git grep __GFP_REPEAT origin/master | wc -l
111
$ git grep __GFP_REPEAT | wc -l
36
So we are down to the third after this patch series. The remaining
places really seem to be relying on __GFP_REPEAT due to large allocation
requests. This still needs some double checking which I will do later
after all the simple ones are sorted out.
I am touching a lot of arch specific code here and I hope I got it right
but as a matter of fact I even didn't compile test for some archs as I
do not have cross compiler for them. Patches should be quite trivial to
review for stupid compile mistakes though. The tricky parts are usually
hidden by macro definitions and thats where I would appreciate help from
arch maintainers.
[1] http://lkml.kernel.org/r/1461849846-27209-1-git-send-email-mhocko@kernel.org
This patch (of 19):
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations. Yet we
have the full kernel tree with its usage for apparently order-0
allocations. This is really confusing because __GFP_REPEAT is
explicitly documented to allow allocation failures which is a weaker
semantic than the current order-0 has (basically nofail).
Let's simply drop __GFP_REPEAT from those places. This would allow to
identify place which really need allocator to retry harder and formulate
a more specific semantic for what the flag is supposed to do actually.
Link: http://lkml.kernel.org/r/1464599699-30131-2-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com> [for tile]
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: John Crispin <blogic@openwrt.org>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As the actual pointer value is the same for the thread stack allocation
and the thread_info, code that confused the two worked fine, but will
break when the thread info is moved away from the stack allocation. It
also looks very confusing.
For example, the kprobe code wanted to know the current top of stack.
To do that, it used this:
(unsigned long)current_thread_info() + THREAD_SIZE
which did indeed give the correct value. But it's not only a fairly
nonsensical expression, it's also rather complex, especially since we
actually have this:
static inline unsigned long current_top_of_stack(void)
which not only gives us the value we are interested in, but happens to
be how "current_thread_info()" is currently defined as:
(struct thread_info *)(current_top_of_stack() - THREAD_SIZE);
so using current_thread_info() to figure out the top of the stack really
is a very round-about thing to do.
The other cases are just simpler confusion about task_thread_info() vs
task_stack_page(), which currently return the same pointer - but if you
want the stack page, you really should be using the latter one.
And there was one entirely unused assignment of the current stack to a
thread_info pointer.
All cleaned up to make more sense today, and make it easier to move the
thread_info away from the stack in the future.
No semantic changes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
None of the code actually wants a thread_info, it all wants a
task_struct, and it's just converting to a thread_info pointer much too
early.
No semantic change.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When page tables entries are set using xen_set_pte_init() during early
boot there is no page fault handler that could handle a fault when
performing an M2P lookup.
In 64 bit guests (usually dom0) early_ioremap() would fault in
xen_set_pte_init() because an M2P lookup faults because the MFN is in
MMIO space and not mapped in the M2P. This lookup is done to see if
the PFN in in the range used for the initial page table pages, so that
the PTE may be set as read-only.
The M2P lookup can be avoided by moving the check (and clear of RW)
earlier when the PFN is still available.
Reported-by: Kevin Moraga <kmoragas@riseup.net>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
|
|
xen_cleanhighmap() is operating on level2_kernel_pgt only. The upper
bound of the loop setting non-kernel-image entries to zero should not
exceed the size of level2_kernel_pgt.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are a small number of debugfs, ISA, and one driver core fix for
4.7-rc4.
All of these resolve reported issues. The ISA ones have spent the
least amount of time in linux-next, sorry about that, I didn't realize
they were regressions that needed to get in now (thanks to Thorsten
for the prodding!) but they do all pass the 0-day bot tests. The
others have been in linux-next for a while now.
Full details about them are in the shortlog below"
* tag 'driver-core-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
isa: Dummy isa_register_driver should return error code
isa: Call isa_bus_init before dependent ISA bus drivers register
watchdog: ebc-c384_wdt: Allow build for X86_64
iio: stx104: Allow build for X86_64
gpio: Allow PC/104 devices on X86_64
isa: Allow ISA-style drivers on modern systems
base: make module_create_drivers_dir race-free
debugfs: open_proxy_open(): avoid double fops release
debugfs: full_proxy_open(): free proxy on ->open() failure
kernel/kcov: unproxify debugfs file's fops
|
|
Several modern devices, such as PC/104 cards, are expected to run on
modern systems via an ISA bus interface. Since ISA is a legacy interface
for most modern architectures, ISA support should remain disabled in
general. Support for ISA-style drivers should be enabled on a per driver
basis.
To allow ISA-style drivers on modern systems, this patch introduces the
ISA_BUS_API and ISA_BUS Kconfig options. The ISA bus driver will now
build conditionally on the ISA_BUS_API Kconfig option, which defaults to
the legacy ISA Kconfig option. The ISA_BUS Kconfig option allows the
ISA_BUS_API Kconfig option to be selected on architectures which do not
enable ISA (e.g. X86_64).
The ISA_BUS Kconfig option is currently only implemented for X86
architectures. Other architectures may have their own ISA_BUS Kconfig
options added as required.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull KVM fixes from Paolo Bonzini:
- miscellaneous fixes for MIPS and s390
- one new kvm_stat for s390
- correctly disable VT-d posted interrupts with the rest of posted
interrupts
- "make randconfig" fix for x86 AMD
- off-by-one in irq route check (the "good" kind that errors out a bit
too early!)
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vmx: check apicv is active before using VT-d posted interrupt
kvm: Fix irq route entries exceeding KVM_MAX_IRQ_ROUTES
kvm: svm: Do not support AVIC if not CONFIG_X86_LOCAL_APIC
kvm: svm: Fix implicit declaration for __default_cpu_present_to_apicid()
MIPS: KVM: Fix CACHE triggered exception emulation
MIPS: KVM: Don't unwind PC when emulating CACHE
MIPS: KVM: Include bit 31 in segment matches
MIPS: KVM: Fix modular KVM under QEMU
KVM: s390: Add stats for PEI events
KVM: s390: ignore IBC if zero
|
|
VT-d posted interrupt is relying on the CPU side's posted interrupt.
Need to check whether VCPU's APICv is active before enabing VT-d
posted interrupt.
Fixes: d62caabb41f33d96333f9ef15e09cd26e1c12760
Cc: stable@vger.kernel.org
Signed-off-by: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Shengge Ding <shengge.dsg@alibaba-inc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add logic to disable AVIC #ifndef CONFIG_X86_LOCAL_APIC.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The commit 8221c1370056 ("svm: Manage vcpu load/unload when enable AVIC")
introduces a build error due to implicit function declaration
when #ifdef CONFIG_X86_32 and #ifndef CONFIG_X86_LOCAL_APIC
(as reported by Kbuild test robot i386-randconfig-x0-06121009).
So, this patch introduces kvm_cpu_get_apicid() wrapper
around __default_cpu_present_to_apicid() with additional
handling if CONFIG_X86_LOCAL_APIC is not defined.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: commit 8221c1370056 ("svm: Manage vcpu load/unload when enable AVIC")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix kprobe_fault_handler() to clear the TF (trap flag) bit of
the flags register in the case of a fault fixup on single-stepping.
If we put a kprobe on the instruction which caused a
page fault (e.g. actual mov instructions in copy_user_*),
that fault happens on the single-stepping buffer. In this
case, kprobes resets running instance so that the CPU can
retry execution on the original ip address.
However, current code forgets to reset the TF bit. Since this
fault happens with TF bit set for enabling single-stepping,
when it retries, it causes a debug exception and kprobes
can not handle it because it already reset itself.
On the most of x86-64 platform, it can be easily reproduced
by using kprobe tracer. E.g.
# cd /sys/kernel/debug/tracing
# echo p copy_user_enhanced_fast_string+5 > kprobe_events
# echo 1 > events/kprobes/enable
And you'll see a kernel panic on do_debug(), since the debug
trap is not handled by kprobes.
To fix this problem, we just need to clear the TF bit when
resetting running kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: systemtap@sourceware.org
Cc: stable@vger.kernel.org # All the way back to ancient kernels
Link: http://lkml.kernel.org/r/20160611140648.25885.37482.stgit@devbox
[ Updated the comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes from all around the map, plus a commit that introduces a
new header of Intel model name symbols (unused) that will make the
next merge window easier"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioapic: Fix incorrect pointers in ioapic_setup_resources()
x86/entry/traps: Don't force in_interrupt() to return true in IST handlers
x86/cpu/AMD: Extend X86_FEATURE_TOPOEXT workaround to newer models
x86/cpu/intel: Introduce macros for Intel family numbers
x86, build: copy ldlinux.c32 to image.iso
x86/msr: Use the proper trace point conditional for writes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A handful of tooling fixes, two PMU driver fixes and a cleanup of
redundant code that addresses a security analyzer false positive"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove a redundant check
perf/x86/intel/uncore: Remove SBOX support for Broadwell server
perf ctf: Convert invalid chars in a string before set value
perf record: Fix crash when kptr is restricted
perf symbols: Check kptr_restrict for root
perf/x86/intel/rapl: Fix pmus free during cleanup
|
|
On a 4-socket Brickland system, hot-removing one ioapic is fine.
Hot-removing the 2nd one causes panic in mp_unregister_ioapic()
while calling release_resource().
It is because the iomem_res pointer has already been released
when removing the first ioapic.
To explain the use of &res[num] here: res is assigned to ioapic_resources,
and later in ioapic_insert_resources() we do:
struct resource *r = ioapic_resources;
for_each_ioapic(i) {
insert_resource(&iomem_resource, r);
r++;
}
Here 'r' is treated as an arry of 'struct resource', and the r++ ensures
that each element of the array is inserted separately. Thus we should call
release_resouce() on each element at &res[num].
Fix it by assigning the correct pointers to ioapics[i].iomem_res in
ioapic_setup_resources().
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: tony.luck@intel.com
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1465369193-4816-3-git-send-email-rui.y.wang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Forcing in_interrupt() to return true if we're not in a bona fide
interrupt confuses the softirq code. This fixes warnings like:
NOHZ: local_softirq_pending 282
... which can happen when running things like selftests/x86.
This will change perf's static percpu buffer usage in IST context.
I think this is okay, and it's changing the behavior to match
historical (pre-4.0) behavior.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 959274753857 ("x86, traps: Track entry into and exit from IST context")
Link: http://lkml.kernel.org/r/cdc215f94d118d691d73df35275022331156fb45.1464130360.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We need to reenable the topology extensions CPUID leafs on newer models
too, if BIOS has disabled them, as we rely on them to get proper compute
unit topology.
Make the printk a once thing, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rui Huang <ray.huang@amd.com>
Cc: Sherry Hurwitz <sherry.hurwitz@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-hwmon@vger.kernel.org
Link: http://lkml.kernel.org/r/1464775468-23355-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Problem:
We have a boatload of open-coded family-6 model numbers. Half of
them have these model numbers in hex and the other half in
decimal. This makes grepping for them tons of fun, if you were
to try.
Solution:
Consolidate all the magic numbers. Put all the definitions in
one header.
The names here are closely derived from the comments describing
the models from arch/x86/events/intel/core.c. We could easily
make them shorter by doing things like s/SANDYBRIDGE/SNB/, but
they seemed fine even with the longer versions to me.
Do not take any of these names too literally, like "DESKTOP"
or "MOBILE". These are all colloquial names and not precise
descriptions of everywhere a given model will show up.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Cc: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: jacob.jun.pan@intel.com
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Link: http://lkml.kernel.org/r/20160603001927.F2A7D828@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For newer versions of Syslinux, we need ldlinux.c32 in addition to
isolinux.bin to reside on the boot disk, so if the latter is found,
copy it, too, to the isoimage tree.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Linux Stable Tree <stable@vger.kernel.org>
|
|
The msr tracing for writes is incorrectly conditional on the read trace.
Fixes: 7f47d8cc039f "x86, tracing, perf: Add trace point for MSR accesses"
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: stable@vger.kernel.org
Cc: ak@linux.intel.com
Link: http://lkml.kernel.org/r/1464976859-21850-1-git-send-email-dgilbert@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There was a report that on certain Broadwell-EP systems writing any bit of
the SBOX PMU initialization MSR would #GP at boot. This did not happen
on all systems. My test systems booted fine.
Considering both DE and EP may have such issues, this patch removes SBOX
support for all Broadwell platforms for now.
Reported-and-tested-by: Mark van Dijk <mark@voidzero.net>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1464347540-5763-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to
any of bits 63:32. However, this is not detected at KVM_SET_DEBUGREGS
time, and the next KVM_RUN oopses:
general protection fault: 0000 [#1] SMP
CPU: 2 PID: 14987 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
[...]
Call Trace:
[<ffffffffa072c93d>] kvm_arch_vcpu_ioctl_run+0x141d/0x14e0 [kvm]
[<ffffffffa071405d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
[<ffffffff81241648>] do_vfs_ioctl+0x298/0x480
[<ffffffff812418a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a0f2e>] entry_SYSCALL_64_fastpath+0x12/0x71
Code: 55 83 ff 07 48 89 e5 77 27 89 ff ff 24 fd 90 87 80 81 0f 23 fe 5d c3 0f 23 c6 5d c3 0f 23 ce 5d c3 0f 23 d6 5d c3 0f 23 de 5d c3 <0f> 23 f6 5d c3 0f 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
RIP [<ffffffff810639eb>] native_set_debugreg+0x2b/0x40
RSP <ffff88005836bd50>
Testcase (beautified/reduced from syzkaller output):
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[8];
int main()
{
struct kvm_debugregs dr = { 0 };
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);
memcpy(&dr,
"\x5d\x6a\x6b\xe8\x57\x3b\x4b\x7e\xcf\x0d\xa1\x72"
"\xa3\x4a\x29\x0c\xfc\x6d\x44\x00\xa7\x52\xc7\xd8"
"\x00\xdb\x89\x9d\x78\xb5\x54\x6b\x6b\x13\x1c\xe9"
"\x5e\xd3\x0e\x40\x6f\xb4\x66\xf7\x5b\xe3\x36\xcb",
48);
r[7] = ioctl(r[4], KVM_SET_DEBUGREGS, &dr);
r[6] = ioctl(r[4], KVM_RUN, 0);
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
This cannot be returned by KVM_GET_VCPU_EVENTS, so it is okay to return
EINVAL. It causes a WARN from exception_type:
WARNING: CPU: 3 PID: 16732 at arch/x86/kvm/x86.c:345 exception_type+0x49/0x50 [kvm]()
CPU: 3 PID: 16732 Comm: a.out Tainted: G W 4.4.6-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
0000000000000286 000000006308a48b ffff8800bec7fcf8 ffffffff813b542e
0000000000000000 ffffffffa0966496 ffff8800bec7fd30 ffffffff810a40f2
ffff8800552a8000 0000000000000000 00000000002c267c 0000000000000001
Call Trace:
[<ffffffff813b542e>] dump_stack+0x63/0x85
[<ffffffff810a40f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff810a423a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0924809>] exception_type+0x49/0x50 [kvm]
[<ffffffffa0934622>] kvm_arch_vcpu_ioctl_run+0x10a2/0x14e0 [kvm]
[<ffffffffa091c04d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
[<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
[<ffffffff812414a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
---[ end trace b1a0391266848f50 ]---
Testcase (beautified/reduced from syzkaller output):
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <fcntl.h>
#include <sys/ioctl.h>
#include <linux/kvm.h>
long r[31];
int main()
{
memset(r, -1, sizeof(r));
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[7] = ioctl(r[3], KVM_CREATE_VCPU, 0);
struct kvm_vcpu_events ve = {
.exception.injected = 1,
.exception.nr = 0xd4
};
r[27] = ioctl(r[7], KVM_SET_VCPU_EVENTS, &ve);
r[30] = ioctl(r[7], KVM_RUN, 0);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
This causes an ugly dmesg splat. Beautified syzkaller testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/kvm.h>
long r[8];
int main()
{
struct kvm_cpuid2 c = { 0 };
r[2] = open("/dev/kvm", O_RDWR);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 0x8);
r[7] = ioctl(r[4], KVM_SET_CPUID, &c);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Found by syzkaller:
WARNING: CPU: 3 PID: 15175 at arch/x86/kvm/x86.c:7705 __x86_set_memory_region+0x1dc/0x1f0 [kvm]()
CPU: 3 PID: 15175 Comm: a.out Tainted: G W 4.4.6-300.fc23.x86_64 #1
Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
0000000000000286 00000000950899a7 ffff88011ab3fbf0 ffffffff813b542e
0000000000000000 ffffffffa0966496 ffff88011ab3fc28 ffffffff810a40f2
00000000000001fd 0000000000003000 ffff88014fc50000 0000000000000000
Call Trace:
[<ffffffff813b542e>] dump_stack+0x63/0x85
[<ffffffff810a40f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff810a423a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa09251cc>] __x86_set_memory_region+0x1dc/0x1f0 [kvm]
[<ffffffffa092521b>] x86_set_memory_region+0x3b/0x60 [kvm]
[<ffffffffa09bb61c>] vmx_set_tss_addr+0x3c/0x150 [kvm_intel]
[<ffffffffa092f4d4>] kvm_arch_vm_ioctl+0x654/0xbc0 [kvm]
[<ffffffffa091d31a>] kvm_vm_ioctl+0x9a/0x6f0 [kvm]
[<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
[<ffffffff812414a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
Testcase:
#include <unistd.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <string.h>
#include <linux/kvm.h>
long r[8];
int main()
{
memset(r, -1, sizeof(r));
r[2] = open("/dev/kvm", O_RDONLY|O_TRUNC);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0x0ul);
r[5] = ioctl(r[3], KVM_SET_TSS_ADDR, 0x20000000ul);
r[7] = ioctl(r[3], KVM_SET_TSS_ADDR, 0x20000000ul);
return 0;
}
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Intel CPUs having Turbo Boost feature implement an MSR to provide a
control interface via rdmsr/wrmsr instructions. One could detect the
presence of this feature by issuing one of these instructions and
handling the #GP exception which is generated in case the referenced MSR
is not implemented by the CPU.
KVM's vCPU model behaves exactly as a real CPU in this case by injecting
a fault when MSR_IA32_PERF_CTL is called (which KVM does not support).
However, some operating systems use this register during an early boot
stage in which their kernel is not capable of handling #GP correctly,
causing #DP and finally a triple fault effectively resetting the vCPU.
This patch implements a dummy handler for MSR_IA32_PERF_CTL to avoid the
crashes.
Signed-off-by: Dmitry Bilunov <kmeaw@yandex-team.ru>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
In theory, nothing prevents the compiler from write-tearing PTEs, or
split PTE writes. These partially-modified PTEs can be fetched by other
cores and cause mayhem. I have not really encountered such case in
real-life, but it does seem possible.
For example, the compiler may try to do something creative for
kvm_set_pte_rmapp() and perform multiple writes to the PTE.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
"This contains a nice FPU fixup from Eli Cooper for UML"
* 'for-linus-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: add extended processor state save/restore support
um: extend fpstate to _xstate to support YMM registers
um: fix FPU state preservation around signal handlers
|
|
The do_brk() and vm_brk() return value was "unsigned long" and returned
the starting address on success, and an error value on failure. The
reasons are entirely historical, and go back to it basically behaving
like the mmap() interface does.
However, nobody actually wanted that interface, and it causes totally
pointless IS_ERR_VALUE() confusion.
What every single caller actually wants is just the simpler integer
return of zero for success and negative error number on failure.
So just convert to that much clearer and more common calling convention,
and get rid of all the IS_ERR_VALUE() uses wrt vm_brk().
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Mostly minor updates and cleanups. One new power management
controller driver for Intel Core SoCs.
platform/x86:
- Add PMC Driver for Intel Core SoC
dell-rbtn:
- Ignore ACPI notifications if device is suspended
thinkpad_acpi:
- save kbdlight state on suspend and restore it on resume
intel_menlow:
- reduce code duplication
asus-wmi:
- provide access to ALS control
ideapad-laptop:
- add a new WMI string for ESC key
surfacepro3_button:
- Add a warning when switching to tablet mode
sony-laptop:
- Avoid oops on module unload for older laptops
intel_telemetry:
- Constify telemetry_core_ops structures
fujitsu-laptop:
- Use IS_ENABLED() instead of checking for built-in or module
asus-laptop:
- correct error handling in sysfs_acpi_set
- remove redundant initializers
- correct error handling in asus_read_brightness()
fujitsu-laptop:
- Support radio LED"
* tag 'platform-drivers-x86-v4.7-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: Add PMC Driver for Intel Core SoC
dell-rbtn: Ignore ACPI notifications if device is suspended
thinkpad_acpi: save kbdlight state on suspend and restore it on resume
intel_menlow: reduce code duplication
asus-wmi: provide access to ALS control
ideapad-laptop: add a new WMI string for ESC key
surfacepro3_button: Add a warning when switching to tablet mode
sony-laptop: Avoid oops on module unload for older laptops
intel_telemetry: Constify telemetry_core_ops structures
fujitsu-laptop: Use IS_ENABLED() instead of checking for built-in or module
asus-laptop: correct error handling in sysfs_acpi_set
asus-laptop: remove redundant initializers
asus-laptop: correct error handling in asus_read_brightness()
fujitsu-laptop: Support radio LED
|
|
Pull second batch of KVM updates from Radim Krčmář:
"General:
- move kvm_stat tool from QEMU repo into tools/kvm/kvm_stat (kvm_stat
had nothing to do with QEMU in the first place -- the tool only
interprets debugfs)
- expose per-vm statistics in debugfs and support them in kvm_stat
(KVM always collected per-vm statistics, but they were summarised
into global statistics)
x86:
- fix dynamic APICv (VMX was improperly configured and a guest could
access host's APIC MSRs, CVE-2016-4440)
- minor fixes
ARM changes from Christoffer Dall:
- new vgic reimplementation of our horribly broken legacy vgic
implementation. The two implementations will live side-by-side
(with the new being the configured default) for one kernel release
and then we'll remove the legacy one.
- fix for a non-critical issue with virtual abort injection to guests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (70 commits)
tools: kvm_stat: Add comments
tools: kvm_stat: Introduce pid monitoring
KVM: Create debugfs dir and stat files for each VM
MAINTAINERS: Add kvm tools
tools: kvm_stat: Powerpc related fixes
tools: Add kvm_stat man page
tools: Add kvm_stat vm monitor script
kvm:vmx: more complete state update on APICv on/off
KVM: SVM: Add more SVM_EXIT_REASONS
KVM: Unify traced vector format
svm: bitwise vs logical op typo
KVM: arm/arm64: vgic-new: Synchronize changes to active state
KVM: arm/arm64: vgic-new: enable build
KVM: arm/arm64: vgic-new: implement mapped IRQ handling
KVM: arm/arm64: vgic-new: Wire up irqfd injection
KVM: arm/arm64: vgic-new: Add vgic_v2/v3_enable
KVM: arm/arm64: vgic-new: vgic_init: implement map_resources
KVM: arm/arm64: vgic-new: vgic_init: implement vgic_init
KVM: arm/arm64: vgic-new: vgic_init: implement vgic_create
KVM: arm/arm64: vgic-new: vgic_init: implement kvm_vgic_hyp_init
...
|
|
This patch adds the Power Management Controller driver as a PCI driver
for Intel Core SoC architecture.
This driver can utilize debugging capabilities and supported features
as exposed by the Power Management Controller.
Please refer to the below specification for more details on PMC features.
http://www.intel.in/content/www/in/en/chipsets/100-series-chipset-datasheet-vol-2.html
The current version of this driver exposes SLP_S0_RESIDENCY counter.
This counter can be used for detecting fragile SLP_S0 signal related
failures and take corrective actions when PCH SLP_S0 signal is not
asserted after kernel freeze as part of suspend to idle flow
(echo freeze > /sys/power/state).
Intel Platform Controller Hub (PCH) asserts SLP_S0 signal when it
detects favorable conditions to enter its low power mode. As a
pre-requisite the SoC should be in deepest possible Package C-State
and devices should be in low power mode. For example, on Skylake SoC
the deepest Package C-State is Package C10 or PC10. Suspend to idle
flow generally leads to PC10 state but PC10 state may not be sufficient
for realizing the platform wide power potential which SLP_S0 signal
assertion can provide.
SLP_S0 signal is often connected to the Embedded Controller (EC) and the
Power Management IC (PMIC) for other platform power management related
optimizations.
In general, SLP_S0 assertion == PC10 + PCH low power mode + ModPhy Lanes
power gated + PLL Idle.
As part of this driver, a mechanism to read the SLP_S0_RESIDENCY is exposed
as an API and also debugfs features are added to indicate SLP_S0 signal
assertion residency in microseconds.
echo freeze > /sys/power/state
wake the system
cat /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- new option CONFIG_TRIM_UNUSED_KSYMS which does a two-pass build and
unexports symbols which are not used in the current config [Nicolas
Pitre]
- several kbuild rule cleanups [Masahiro Yamada]
- warning option adjustments for gcov etc [Arnd Bergmann]
- a few more small fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (31 commits)
kbuild: move -Wunused-const-variable to W=1 warning level
kbuild: fix if_change and friends to consider argument order
kbuild: fix adjust_autoksyms.sh for modules that need only one symbol
kbuild: fix ksym_dep_filter when multiple EXPORT_SYMBOL() on the same line
gcov: disable -Wmaybe-uninitialized warning
gcov: disable tree-loop-im to reduce stack usage
gcov: disable for COMPILE_TEST
Kbuild: disable 'maybe-uninitialized' warning for CONFIG_PROFILE_ALL_BRANCHES
Kbuild: change CC_OPTIMIZE_FOR_SIZE definition
kbuild: forbid kernel directory to contain spaces and colons
kbuild: adjust ksym_dep_filter for some cmd_* renames
kbuild: Fix dependencies for final vmlinux link
kbuild: better abstract vmlinux sequential prerequisites
kbuild: fix call to adjust_autoksyms.sh when output directory specified
kbuild: Get rid of KBUILD_STR
kbuild: rename cmd_as_s_S to cmd_cpp_s_S
kbuild: rename cmd_cc_i_c to cmd_cpp_i_c
kbuild: drop redundant "PHONY += FORCE"
kbuild: delete unnecessary "@:"
kbuild: mark help target as PHONY
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: EFI, entry code, pkeys and MPX fixes, TASK_SIZE cleanups
and a tsc frequency table fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Switch from TASK_SIZE to TASK_SIZE_MAX in the page fault code
x86/fsgsbase/64: Use TASK_SIZE_MAX for FSBASE/GSBASE upper limits
x86/mm/mpx: Work around MPX erratum SKD046
x86/entry/64: Fix stack return address retrieval in thunk
x86/efi: Fix 7-parameter efi_call()s
x86/cpufeature, x86/mm/pkeys: Fix broken compile-time disabling of pkeys
x86/tsc: Add missing Cherrytrail frequency to the table
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Mostly tooling and PMU driver fixes, but also a number of late updates
such as the reworking of the call-chain size limiting logic to make
call-graph recording more robust, plus tooling side changes for the
new 'backwards ring-buffer' extension to the perf ring-buffer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
perf record: Read from backward ring buffer
perf record: Rename variable to make code clear
perf record: Prevent reading invalid data in record__mmap_read
perf evlist: Add API to pause/resume
perf trace: Use the ptr->name beautifier as default for "filename" args
perf trace: Use the fd->name beautifier as default for "fd" args
perf report: Add srcline_from/to branch sort keys
perf evsel: Record fd into perf_mmap
perf evsel: Add overwrite attribute and check write_backward
perf tools: Set buildid dir under symfs when --symfs is provided
perf trace: Only auto set call-graph to "dwarf" when syscalls are being traced
perf annotate: Sort list of recognised instructions
perf annotate: Fix identification of ARM blt and bls instructions
perf tools: Fix usage of max_stack sysctl
perf callchain: Stop validating callchains by the max_stack sysctl
perf trace: Fix exit_group() formatting
perf top: Use machine->kptr_restrict_warned
perf trace: Warn when trying to resolve kernel addresses with kptr_restrict=1
perf machine: Do not bail out if not managing to read ref reloc symbol
perf/x86/intel/p4: Trival indentation fix, remove space
...
|
|
The function to update APICv on/off state (in particular, to deactivate
it when enabling Hyper-V SynIC) is incomplete: it doesn't adjust
APICv-related fields among secondary processor-based VM-execution
controls. As a result, Windows 2012 guests get stuck when SynIC-based
auto-EOI interrupt intersected with e.g. an IPI in the guest.
In addition, the MSR intercept bitmap isn't updated every time "virtualize
x2APIC mode" is toggled. This path can only be triggered by a malicious
guest, because Windows didn't use x2APIC but rather their own synthetic
APIC access MSRs; however a guest running in a SynIC-enabled VM could
switch to x2APIC and thus obtain direct access to host APIC MSRs
(CVE-2016-4440).
The patch fixes those omissions.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Reported-by: Steve Rutherford <srutherford@google.com>
Reported-by: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
On rapl cleanup path, kfree() is given by mistake the address of the
pointer of the structure to free (rapl_pmus->pmus + i). Pass the pointer
instead (rapl_pmus->pmus[i]).
Fixes: 9de8d686955b "perf/x86/intel/rapl: Convert it to a per package facility"
Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1464101629-14905-1-git-send-email-vincent.stehle@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel.
* tag 'for-linus-4.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: use same main loop for counting and remapping pages
xen/events: Don't move disabled irqs
xen/x86: actually allocate legacy interrupts on PV guests
Xen: don't warn about 2-byte wchar_t in efi
xen/gntdev: reduce copy batch size to 16
xen/x86: don't lose event interrupts
|
|
Instead of having two functions for cycling through the E820 map in
order to count to be remapped pages and remap them later, just use one
function with a caller supplied sub-function called for each region to
be processed. This eliminates the possibility of a mismatch between
both loops which showed up in certain configurations.
Suggested-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
b4ff8389ed14 is incomplete: relies on nr_legacy_irqs() to get the number
of legacy interrupts when actually nr_legacy_irqs() returns 0 after
probe_8259A(). Use NR_IRQS_LEGACY instead.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
CC: stable@vger.kernel.org
|
|
On slow platforms with unreliable TSC, such as QEMU emulated machines,
it is possible for the kernel to request the next event in the past. In
that case, in the current implementation of xen_vcpuop_clockevent, we
simply return -ETIME. To be precise the Xen returns -ETIME and we pass
it on. However the result of this is a missed event, which simply causes
the kernel to hang.
Instead it is better to always ask the hypervisor for a timer event,
even if the timeout is in the past. That way there are no lost
interrupts and the kernel survives. To do that, remove the
VCPU_SSHOTTMR_future flag.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com>
|
|
Useful when tracing nested setups where the guest may trigger more than
the host usually does. But even some typical host exits were missing.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These were supposed to be a bitwise operation but there is a typo.
The result is mostly harmless, but sparse correctly complains.
Fixes: 44a95dae1d22 ('KVM: x86: Detect and Initialize AVIC support')
Fixes: 18f40c53e10f ('svm: Add VMEXIT handlers for AVIC')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
