Age | Commit message (Collapse) | Author |
|
There are two sleep related pins on rk3399: ap_pwroff and ddrio_pwroff.
Let's add the definition of these two pins to rk3399's main dtsi file so
that boards can use them.
These two pins are similar to the global_pwroff and ddrio_pwroff pins in
rk3288 and are expected to be used in the same way: boards will likely
want to configure these pinctrl settings in their global pinctrl hog
list.
Note that on rk3288 there were two additional pins in the "sleep"
section: "ddr0_retention" and "ddr1_retention". On rk3288 designs these
pins appeared to actually route from rk3288 back to rk3288. Presumably
on rk3399 this is simply not needed since the pins don't appear to exist
there.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Previous changes in this series allowed exposing the card clock from the
rk3399 SDHCI device and allowed consuming the card clock in the rk3399
eMMC PHY. Hook things up in the main rk3399 dtsi file.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
On rk3399 we'd like to be able to properly set corecfg registers in the
Arasan SDHCI component. Specify the syscon to enable that.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The 2nd additional region is the GIC virtual cpu interface register
base and size.
As the gic400 of rk3368 says, the cpu interface register map as below
:
-0x0000 GICC_CTRL
.
.
.
-0x00fc GICC_IIDR
-0x1000 GICC_IDR
Obviously, the region size should be greater than 0x1000.
So we should make sure to include the GICC_IDR since the kernel will access
it in some cases.
Fixes: b790c2cab5ca ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
[added Fixes and stable-cc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We've got 9 (count em!) i2c controllers on rk3399, some of which are in
the PMU power domain and some of which are normal peripherals. Add them
all to the main rk3399 dtsi file so future patches can turn them on in
the board dts files.
Note: by default we try to set the i2c clock rate to 200 MHz so that we
can achieve good i2c functional clock rates. 200 MHz gives us the
ability to make very close to 100 kHz / 400 kHz / 1 MHz rates. If
boards want to tune clock rates further they can always override.
Possibly boards could want to tune this if:
- they wanted to save an infinitesimal amount of power and they knew
their i2c bus was slow anyway. Since we gate the functional clock
when the i2c bus is not active, power savings would only be while i2c
transfers were happening and probably won't be very big anyway.
- they wanted to eek out a bit more speed by carefully tuning the source
clock to make divisions work out perfectly, accounting for the rise /
fall time measured on an actual board.
Note also that we still request 200 MHz for the PMU i2c busses even
though we expect that we won't make that exactly (currently PPLL is 676
MHz which gives us 169 MHz).
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
[dianders: wrote desc; put in assigned-clocks; reordered nodes]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This adds thermal zone and tsadc nodes to rk3399 dtsi, rk3399 thermal
data is including the cpu and gpu sensor zone node.
The thermal zone node is the node containing all the required info
for describing a thermal zone, including its cooling device bindings.
The thermal zone node must contain, apart from its own properties, one
sub-node containing trip nodes and one sub-node containing all the zone
cooling maps.
The following is the parameter is introduced:
* polling-delay:
The maximum number of milliseconds to wait between polls
* polling-delay-passive:
The maximum number of milliseconds to wait between polls when performing
passive cooling.
* trips:
A sub-node which is a container of only trip point nodes required to
describe the thermal zone.
* cooling-maps:
A sub-node which is a container of only cooling device map nodes, used to
describe the relation between trips and cooling devices.
* cooling-device:
A phandle of a cooling device with its specifier, referring to which
cooling device is used in this cooling specifier binding. In the cooling
specifier, the first cell is the minimum cooling state and the second cell
is the maximum cooling state used in this map.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the core io-domain nodes to grf and pmugrf which individual
boards than just have to enable and add the necessary supplies to.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the supply-links according to the R88 schematics.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the core io-domain nodes to grf and pmugrf which individual
boards than just have to enable and add the necessary supplies to.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The general register files do contain a lot of separate functions and
while some really are only registers with a lot of different 1-bit
settings, there are also a lot of them containing some bigger function
blocks. To be able to define these as sub-devices, make them simple-mfds.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: David Wu <david.wu@rock-chips.com>
|
|
Rockchip's rk3399 evaluation board has eMMC. Let's enable the
newly-added nodes.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add description for the SDHCI v5.1 eMMC controller on rk3399. Fix it to
200 MHz, to support all supported timing modes.
Note that 'rockchip,rk3399-sdhci-5.1' is not documented; we presumably
have a compliant Arasan controller, but let's have a rockchip property
as the canonical backup/precautionary measure. Per Heiko's previous
suggestion, let's not clutter the arasan doc with it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Per the examples in
Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt, we need the
grf node to be a simple-mfd in order to properly enumerate child devices
like our eMMC PHY.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[directly mimic for the pmugrf, which will need the same change later
and there is no need to pollute commit history with another patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
These clocks are all core clocks used by many blocks/peripherals, many
of whose drivers don't set their clock rates at all. Let's assign
reasonable default clock rates for these core clocks, so that these
peripherals get something reasonable by default, and also so that if
child devices want to select a clock rate themselves, their muxes have
some reasonable parent clock rates to branch off of (rather than just
the boot-time defaults).
This helps the eMMC PHY, for one, to get a reasonable ACLK rate.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull more MIPS updates from Ralf Baechle:
"This is the secondnd batch of MIPS patches for 4.7. Summary:
CPS:
- Copy EVA configuration when starting secondary VPs.
EIC:
- Clear Status IPL.
Lasat:
- Fix a few off by one bugs.
lib:
- Mark intrinsics notrace. Not only are the intrinsics
uninteresting, it would cause infinite recursion.
MAINTAINERS:
- Add file patterns for MIPS BRCM device tree bindings.
- Add file patterns for mips device tree bindings.
MT7628:
- Fix MT7628 pinmux typos.
- wled_an pinmux gpio.
- EPHY LEDs pinmux support.
Pistachio:
- Enable KASLR
VDSO:
- Build microMIPS VDSO for microMIPS kernels.
- Fix aliasing warning by building with `-fno-strict-aliasing' for
debugging but also tracing them might result in recursion.
Misc:
- Add missing FROZEN hotplug notifier transitions.
- Fix clk binding example for varioius PIC32 devices.
- Fix cpu interrupt controller node-names in the DT files.
- Fix XPA CPU feature separation.
- Fix write_gc0_* macros when writing zero.
- Add inline asm encoding helpers.
- Add missing VZ accessor microMIPS encodings.
- Fix little endian microMIPS MSA encodings.
- Add 64-bit HTW fields and fix its configuration.
- Fix sigreturn via VDSO on microMIPS kernel.
- Lots of typo fixes.
- Add definitions of SegCtl registers and use them"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (49 commits)
MIPS: Add missing FROZEN hotplug notifier transitions
MIPS: Build microMIPS VDSO for microMIPS kernels
MIPS: Fix sigreturn via VDSO on microMIPS kernel
MIPS: devicetree: fix cpu interrupt controller node-names
MIPS: VDSO: Build with `-fno-strict-aliasing'
MIPS: Pistachio: Enable KASLR
MIPS: lib: Mark intrinsics notrace
MIPS: Fix 64-bit HTW configuration
MIPS: Add 64-bit HTW fields
MAINTAINERS: Add file patterns for mips device tree bindings
MAINTAINERS: Add file patterns for mips brcm device tree bindings
MIPS: Simplify DSP instruction encoding macros
MIPS: Add missing tlbinvf/XPA microMIPS encodings
MIPS: Fix little endian microMIPS MSA encodings
MIPS: Add missing VZ accessor microMIPS encodings
MIPS: Add inline asm encoding helpers
MIPS: Spelling fix lets -> let's
MIPS: VR41xx: Fix typo
MIPS: oprofile: Fix typo
MIPS: math-emu: Fix typo
...
|
|
Pull string hash improvements from George Spelvin:
"This series does several related things:
- Makes the dcache hash (fs/namei.c) useful for general kernel use.
(Thanks to Bruce for noticing the zero-length corner case)
- Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
above.
- Avoids 64-bit multiplies in hash_64() on 32-bit platforms. Two
32-bit multiplies will do well enough.
- Rids the world of the bad hash multipliers in hash_32.
This finishes the job started in commit 689de1d6ca95 ("Minimal
fix-up of bad hashing behavior of hash_64()")
The vast majority of Linux architectures have hardware support for
32x32-bit multiply and so derive no benefit from "simplified"
multipliers.
The few processors that do not (68000, h8/300 and some models of
Microblaze) have arch-specific implementations added. Those
patches are last in the series.
- Overhauls the dcache hash mixing.
The patch in commit 0fed3ac866ea ("namei: Improve hash mixing if
CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
Replaced with a much more careful design that's simultaneously
faster and better. (My own invention, as there was noting suitable
in the literature I could find. Comments welcome!)
- Modify the hash_name() loop to skip the initial HASH_MIX(). This
would let us salt the hash if we ever wanted to.
- Sort out partial_name_hash().
The hash function is declared as using a long state, even though
it's truncated to 32 bits at the end and the extra internal state
contributes nothing to the result. And some callers do odd things:
- fs/hfs/string.c only allocates 32 bits of state
- fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes
- Modify bytemask_from_count to handle inputs of 1..sizeof(long)
rather than 0..sizeof(long)-1. This would simplify users other
than full_name_hash"
Special thanks to Bruce Fields for testing and finding bugs in v1. (I
learned some humbling lessons about "obviously correct" code.)
On the arch-specific front, the m68k assembly has been tested in a
standalone test harness, I've been in contact with the Microblaze
maintainers who mostly don't care, as the hardware multiplier is never
omitted in real-world applications, and I haven't heard anything from
the H8/300 world"
* 'hash' of git://ftp.sciencehorizons.net/linux:
h8300: Add <asm/hash.h>
microblaze: Add <asm/hash.h>
m68k: Add <asm/hash.h>
<linux/hash.h>: Add support for architecture-specific functions
fs/namei.c: Improve dcache hash function
Eliminate bad hash multipliers from hash_32() and hash_64()
Change hash_64() return value to 32 bits
<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
fs/namei.c: Add hashlen_string() function
Pull out string hash to <linux/stringhash.h>
|
|
This will improve the performance of hash_32() and hash_64(), but due
to complete lack of multi-bit shift instructions on H8, performance will
still be bad in surrounding code.
Designing H8-specific hash algorithms to work around that is a separate
project. (But if the maintainers would like to get in touch...)
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
|
|
Microblaze is an FPGA soft core that can be configured various ways.
If it is configured without a multiplier, the standard __hash_32()
will require a call to __mulsi3, which is a slow software loop.
Instead, use a shift-and-add sequence for the constant multiply.
GCC knows how to do this, but it's not as clever as some.
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
This provides a multiply by constant GOLDEN_RATIO_32 = 0x61C88647
for the original mc68000, which lacks a 32x32-bit multiply instruction.
Yes, the amount of optimization effort put in is excessive. :-)
Shift-add chain found by Yevgen Voronenko's Hcub algorithm at
http://spiral.ece.cmu.edu/mcm/gen.html
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Philippe De Muyter <phdm@macq.eu>
Cc: linux-m68k@lists.linux-m68k.org
|
|
This is just the infrastructure; there are no users yet.
This is modelled on CONFIG_ARCH_RANDOM; a CONFIG_ symbol declares
the existence of <asm/hash.h>.
That file may define its own versions of various functions, and define
HAVE_* symbols (no CONFIG_ prefix!) to suppress the generic ones.
Included is a self-test (in lib/test_hash.c) that verifies the basics.
It is NOT in general required that the arch-specific functions compute
the same thing as the generic, but if a HAVE_* symbol is defined with
the value 1, then equality is tested.
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Philippe De Muyter <phdm@macq.eu>
Cc: linux-m68k@lists.linux-m68k.org
Cc: Alistair Francis <alistai@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
|
|
The corresponding FROZEN hotplug notifier transitions used on
suspend/resume are ignored. Therefore the switch case action argument
is masked with the frozen hotplug notifier transition mask.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: rt@linutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/13351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
MicroMIPS kernels may be expected to run on microMIPS only cores which
don't support the normal MIPS instruction set, so be sure to pass the
-mmicromips flag through to the VDSO cflags.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.
However commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.
Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Here is the quote from [1]:
The unit-address must match the first address specified
in the reg property of the node. If the node has no reg property,
the @ and unit-address must be omitted and the node-name alone
differentiates the node from other nodes at the same level
This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].
[1] Power.org(tm) Standard for Embedded Power Architecture(tm)
Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
Chapter 2.2.1.1 Node Name Requirements
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Avoid an aliasing issue causing a build error in VDSO:
In file included from include/linux/srcu.h:34:0,
from include/linux/notifier.h:15,
from ./arch/mips/include/asm/uprobes.h:9,
from include/linux/uprobes.h:61,
from include/linux/mm_types.h:13,
from ./arch/mips/include/asm/vdso.h:14,
from arch/mips/vdso/vdso.h:27,
from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
return *work_data_bits(work) & WORK_STRUCT_STATIC;
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0. Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO").
Thanks to Tejun for diagnosing this properly!
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.3+
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Allow KASLR to be selected on Pistachio based systems. Tested on a
Creator Ci40.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On certain MIPS32 devices, the ftrace tracer "function_graph" uses
__lshrdi3() during the capturing of trace data. ftrace then attempts to
trace __lshrdi3() which leads to infinite recursion and a stack overflow.
Fix this by marking __lshrdi3() as notrace. Mark the other compiler
intrinsics as notrace in case the compiler decides to use them in the
ftrace path.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 4.2.x-
Patchwork: https://patchwork.linux-mips.org/patch/13354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Hardware page Table Walker (HTW) is being misconfigured on 64-bit
kernels. The PWSize.PS (pointer size) bit determines whether pointers
within directories are loaded as 32-bit or 64-bit addresses, but was
never being set to 1 for 64-bit kernels where the unsigned long in pgd_t
is 64-bits wide.
This actually reduces rather than improves performance when the HTW is
enabled on P6600 since the HTW is initiated lots, but walks are all
aborted due I think to bad intermediate pointers.
Since we were already taking the width of the PTEs into account by
setting PWSize.PTEW, which is the left shift applied to the page table
index *in addition to* the native pointer size, we also need to reduce
PTEW by 1 when PS=1. This is done by calculating PTEW based on the
relative size of pte_t compared to pgd_t.
Finally in order for the HTW to be used when PS=1, the appropriate
XK/XS/XU bits corresponding to the different 64-bit segments need to be
set in PWCtl. We enable only XU for now to enable walking for XUSeg.
Supporting walking for XKSeg would be a bit more involved so is left for
a future patch. It would either require the use of a per-CPU top level
base directory if supported by the HTW (a bit like pgd_current but with
a second entry pointing at swapper_pg_dir), or the HTW would prepend bit
63 of the address to the global directory index which doesn't really
match how we split user and kernel page directories.
Fixes: cab25bc7537b ("MIPS: Extend hardware table walking support to MIPS64")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add field definitions for some of the 64-bit specific Hardware page
Table Walker (HTW) register fields in PWSize and PWCtl, in preparation
for fixing the 64-bit HTW configuration.
Also print these fields out along with the others in print_htw_config().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Simplify the DSP instruction wrapper macros which use explicit encodings
for microMIPS and normal MIPS by using the new encoding macros and
removing duplication.
To me this makes it easier to read since it is much shorter, but it also
ensures .insn is used, preventing objdump disassembling the microMIPS
code as normal MIPS.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13314/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Hardcoded MIPS instruction encodings are provided for tlbinvf, mfhc0 &
mthc0 instructions, but microMIPS encodings are missing. I doubt any
microMIPS cores exist at present which support these instructions, but
the microMIPS encodings exist, and microMIPS cores may support them in
the future. Add the missing microMIPS encodings using the new macros.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When the toolchain doesn't support MSA we encode MSA instructions
explicitly in assembly. Unfortunately we use .word for both MIPS and
microMIPS encodings which is wrong, since 32-bit microMIPS instructions
are made up from a pair of halfwords.
- The most significant halfword always comes first, so for little endian
builds the halves will be emitted in the wrong order.
- 32-bit alignment isn't guaranteed, so the assembler may insert a
16-bit nop instruction to pad the instruction stream to a 32-bit
boundary.
Use the new instruction encoding macros to encode microMIPS MSA
instructions correctly.
Fixes: d96cc3d1ec5d ("MIPS: Add microMIPS MSA support.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <Paul.Burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Toolchains may be used which support microMIPS but not VZ instructions
(i.e. binutis 2.22 & 2.23), so extend the explicitly encoded versions of
the guest COP0 register & guest TLB access macros to support microMIPS
encodings too, using the new macros.
This prevents non-microMIPS instructions being executed in microMIPS
mode during CPU probe on cores supporting VZ (e.g. M5150), which cause
reserved instruction exceptions early during boot.
Fixes: bad50d79255a ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13311/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To allow simplification of macros which use inline assembly to
explicitly encode instructions, add a few simple abstractions to
mipsregs.h which expand to specific microMIPS or normal MIPS encodings
depending on what type of kernel is being built:
_ASM_INSN_IF_MIPS(_enc) : Emit a 32bit MIPS instruction if microMIPS is
not enabled.
_ASM_INSN32_IF_MM(_enc) : Emit a 32bit microMIPS instruction if enabled.
_ASM_INSN16_IF_MM(_enc) : Emit a 16bit microMIPS instruction if enabled.
The macros can be used one after another since the MIPS / microMIPS
macros are mutually exclusive, for example:
__asm__ __volatile__(
".set push\n\t"
".set noat\n\t"
"# mfgc0 $1, $%1, %2\n\t"
_ASM_INSN_IF_MIPS(0x40610000 | %1 << 11 | %2)
_ASM_INSN32_IF_MM(0x002004fc | %1 << 16 | %2 << 11)
"move %0, $1\n\t"
".set pop"
: "=r" (__res)
: "i" (source), "i" (sel));
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13310/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As noticed by Sergei in the discussion of Andrea Gelmini's patch series.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: rric@kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Cc: oprofile-list@lists.sf.net
Patchwork: https://patchwork.linux-mips.org/patch/13334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: macro@imgtec.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: paul.burton@imgtec.com
Cc: macro@imgtec.com
Cc: james.hogan@imgtec.com
Cc: jslaby@suse.cz
Cc: adam.buchbinder@gmail.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13330/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: macro@imgtec.com
Cc: paul.burton@imgtec.com
Cc: Leonid.Yegoshin@imgtec.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: adam.buchbinder@gmail.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13328/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: david.daney@cavium.com
Cc: janne.huttunen@nokia.com
Cc: aaro.koskinen@nokia.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13324/
Patchwork: https://patchwork.linux-mips.org/patch/13325/
Patchwork: https://patchwork.linux-mips.org/patch/13326/
Patchwork: https://patchwork.linux-mips.org/patch/13327/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: chenhc@lemote.com
Cc: viresh.kumar@linaro.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13322/
Patchwork: https://patchwork.linux-mips.org/patch/13332/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13320/
Patchwork: https://patchwork.linux-mips.org/patch/13335/
Patchwork: https://patchwork.linux-mips.org/patch/13336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13318/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: chenhc@lemote.com
Cc: james.hogan@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13317/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|