| Age | Commit message (Collapse) | Author |
|---|
|
To declare MTD OF partitions NAND controller device node should have
a special 'partitions' subnode, the change removes a debug message
from mtd/ofpart on boot:
nxp_lpc3220_slc: 'partitions' subnode not found on /ahb/flash@20020000.
Trying to parse direct subnodes as partitions.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change simplifies layout of EA3250 board description by
referencing device nodes of LPC32xx controllers by label.
No functional change intended.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change adds separate device nodes for SIC1 and SIC2 interrupt
controllers and reparents all defined SIC1 and SIC2 interrupt
producers to the correspondent interrupt controller, this is needed to
perform switching to a new LPC32xx MIC/SIC interrupt controller driver.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The SSP0/SPI1 and SSP1/SPI2 shared pinout and should be disable by
default.
Board specific dts should enable them, as needed.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Preparatory change prior to disabling SSPx controllers
by default in the shared LPC32xx DTSI file.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change adds clock properties to spi peripheral devices,
clock ids are taken from dt-bindings/clock/lpc32xx-clock.h
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Probably most of NXP LPC32xx boards have 13MHz main oscillator and
therefore for HCLK PLL and ARM core clock rate default hardware
setting is 16 * 13MHz = 208MHz, however a user may vary HCLK PLL/ARM
core rate from 156MHz to about 266MHz for 13MHz clock source.
The change explicitly defines HCLK PLL output rate to default 208MHz
to overwrite any settings done by a bootloader, if needed it can be
redefined in a board DTS file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Merge fourth patch-bomb from Andrew Morton:
"A lot more stuff than expected, sorry. A bunch of ocfs2 reviewing was
finished off.
- mhocko's oom-reaper out-of-memory-handler changes
- ocfs2 fixes and features
- KASAN feature work
- various fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (42 commits)
thp: fix typo in khugepaged_scan_pmd()
MAINTAINERS: fill entries for KASAN
mm/filemap: generic_file_read_iter(): check for zero reads unconditionally
kasan: test fix: warn if the UAF could not be detected in kmalloc_uaf2
mm, kasan: stackdepot implementation. Enable stackdepot for SLAB
arch, ftrace: for KASAN put hard/soft IRQ entries into separate sections
mm, kasan: add GFP flags to KASAN API
mm, kasan: SLAB support
kasan: modify kmalloc_large_oob_right(), add kmalloc_pagealloc_oob_right()
include/linux/oom.h: remove undefined oom_kills_count()/note_oom_kill()
mm/page_alloc: prevent merging between isolated and other pageblocks
drivers/memstick/host/r592.c: avoid gcc-6 warning
ocfs2: extend enough credits for freeing one truncate record while replaying truncate records
ocfs2: extend transaction for ocfs2_remove_rightmost_path() and ocfs2_update_edge_lengths() before to avoid inconsistency between inode and et
ocfs2/dlm: move lock to the tail of grant queue while doing in-place convert
ocfs2: solve a problem of crossing the boundary in updating backups
ocfs2: fix occurring deadlock by changing ocfs2_wq from global to local
ocfs2/dlm: fix BUG in dlm_move_lockres_to_recovery_list
ocfs2/dlm: fix race between convert and recovery
ocfs2: fix a deadlock issue in ocfs2_dio_end_io_write()
...
|
|
Implement the stack depot and provide CONFIG_STACKDEPOT. Stack depot
will allow KASAN store allocation/deallocation stack traces for memory
chunks. The stack traces are stored in a hash table and referenced by
handles which reside in the kasan_alloc_meta and kasan_free_meta
structures in the allocated memory chunks.
IRQ stack traces are cut below the IRQ entry point to avoid unnecessary
duplication.
Right now stackdepot support is only enabled in SLAB allocator. Once
KASAN features in SLAB are on par with those in SLUB we can switch SLUB
to stackdepot as well, thus removing the dependency on SLUB stack
bookkeeping, which wastes a lot of memory.
This patch is based on the "mm: kasan: stack depots" patch originally
prepared by Dmitry Chernenkov.
Joonsoo has said that he plans to reuse the stackdepot code for the
mm/page_owner.c debugging facility.
[akpm@linux-foundation.org: s/depot_stack_handle/depot_stack_handle_t]
[aryabinin@virtuozzo.com: comment style fixes]
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
New system calls added in:
f17d8b35452cab31a70d224964cd583fb2845449
vfs: vfs: Define new syscalls preadv2,pwritev2
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
|
|
Pull MTD updates from Brian Norris:
"NAND:
- Add sunxi_nand randomizer support
- begin refactoring NAND ecclayout structs
- fix pxa3xx_nand dmaengine usage
- brcmnand: fix support for v7.1 controller
- add Qualcomm NAND controller driver
SPI NOR:
- add new ls1021a, ls2080a support to Freescale QuadSPI
- add new flash ID entries
- support bottom-block protection for Winbond flash
- support Status Register Write Protect
- remove broken QPI support for Micron SPI flash
JFFS2:
- improve post-mount CRC scan efficiency
General:
- refactor bcm63xxpart parser, to later extend for NAND
- add writebuf size parameter to mtdram
Other minor code quality improvements"
* tag 'for-linus-20160324' of git://git.infradead.org/linux-mtd: (72 commits)
mtd: nand: remove kerneldoc for removed function parameter
mtd: nand: Qualcomm NAND controller driver
dt/bindings: qcom_nandc: Add DT bindings
mtd: nand: don't select chip in nand_chip's block_bad op
mtd: spi-nor: support lock/unlock for a few Winbond chips
mtd: spi-nor: add TB (Top/Bottom) protect support
mtd: spi-nor: add SPI_NOR_HAS_LOCK flag
mtd: spi-nor: use BIT() for flash_info flags
mtd: spi-nor: disallow further writes to SR if WP# is low
mtd: spi-nor: make lock/unlock bounds checks more obvious and robust
mtd: spi-nor: silently drop lock/unlock for already locked/unlocked region
mtd: spi-nor: wait for SR_WIP to clear on initial unlock
mtd: nand: simplify nand_bch_init() usage
mtd: mtdswap: remove useless if (!mtd->ecclayout) test
mtd: create an mtd_oobavail() helper and make use of it
mtd: kill the ecclayout->oobavail field
mtd: nand: check status before reporting timeout
mtd: bcm63xxpart: give width specifier an 'int', not 'size_t'
mtd: mtdram: Add parameter for setting writebuf size
mtd: nand: pxa3xx_nand: kill unused field 'drcmr_cmd'
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"This patchset adds stack usage debug info for parisc and metag (on
both the stack grows upwards), switches to the new generic realative
extable search and sort routines, drops the long time ago removed
syscalls alloc_hugepages and free_hugepages and wires up the new
preadv2 and pwritev2 syscalls"
* 'parisc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Wire up preadv2 and pwritev2 syscalls
parisc: Use generic extable search and sort routines
parisc: Panic immediately when panic_on_oops
parisc,metag: Implement CONFIG_DEBUG_STACK_USAGE option
parisc: Drop alloc_hugepages and free_hugepages syscalls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull second set of arm64 updates from Catalin Marinas:
- KASLR bug fixes: use callee-saved register, boot-time I-cache
maintenance
- inv_entry asm macro fix (EL0 check typo)
- pr_notice("Virtual kernel memory layout...") splitting
- Clean-ups: use p?d_set_huge consistently, allow preemption around
copy_to_user_page, remove unused __local_flush_icache_all()
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: allow preemption in copy_to_user_page
arm64: consistently use p?d_set_huge
arm64: kaslr: use callee saved register to preserve SCTLR across C call
arm64: Split pr_notice("Virtual kernel memory layout...") into multiple pr_cont()
arm64: drop unused __local_flush_icache_all()
arm64: fix KASLR boot-time I-cache maintenance
arm64/kernel: fix incorrect EL0 check in inv_entry macro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM DT changes from Arnd Bergmann:
"Here are some final updates for ARM SoC specific dts files:
- The i.MX changes were sent relatively late, and had a dependency on
the clk tree, so I delayed that a bit. Support for the new i.MX6qp
SoC and a couple of new boards is added in this branch.
- Uniphier renames a few files to match the final product names that
were decided by the company, kudos to the kernel developer(s) for
getting support upstream before the product release. Also two
boards are added. The patches were posted early enough and nice
overall, but we forgot to apply them and decided to give it some
more time in linux-next
- at91 has two small bug fixes"
* tag 'armsoc-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: uniphier: add pinmux node for I2C ch4
ARM: dts: uniphier: add @{address} to EEPROM node
ARM: dts: uniphier: add PH1-Pro4 Sanji board support
ARM: dts: uniphier: add PH1-Pro4 Ace board support
ARM: dts: uniphier: enable I2C channel 2 of ProXstream2 Gentil board
ARM: dts: uniphier: add EEPROM node for ProXstream2 Gentil board
ARM: dts: uniphier: add reference clock nodes
ARM: dts: uniphier: rework UniPhier System Bus nodes
ARM: dts: uniphier: factor out ranges property of support card
arm64: dts: uniphier: rename PH1-LD10 to PH1-LD20
ARM: dts: imx53-qsb: Fix gpio button polarity
ARM: dts: vfxxx: Add DAC node for Vybrid SoC
ARM: dts: imx6q: add missing links between ipu2 and mipi dsi
ARM: dts: imx: Add support for Advantech/GE B850v3
ARM: dts: imx: Add support for Advantech/GE B650v3
ARM: dts: imx: Add support for Advantech/GE B450v3
ARM: dts: imx: Add support for Advantech/GE Bx50v3
ARM: dts: imx: Add Advantech BA-16 Qseven module
...
|
|
Pull h8300 updates from Yoshinori Sato:
"Various h8300 fixes"
* tag 'for-4.6' of git://git.osdn.jp/gitroot/uclinux-h8/linux:
h8300: switch EARLYCON
h8300: dts: Rename the serial port clock to fck
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Nothing major this round. Mostly small clean ups and fixes.
Some visible changes:
- A new flag was added to distinguish traces done in NMI context.
- Preempt tracer now shows functions where preemption is disabled but
interrupts are still enabled.
Other notes:
- Updates were done to function tracing to allow better performance
with perf.
- Infrastructure code has been added to allow for a new histogram
feature for recording live trace event histograms that can be
configured by simple user commands. The feature itself was just
finished, but needs a round in linux-next before being pulled.
This only includes some infrastructure changes that will be needed"
* tag 'trace-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (22 commits)
tracing: Record and show NMI state
tracing: Fix trace_printk() to print when not using bprintk()
tracing: Remove redundant reset per-CPU buff in irqsoff tracer
x86: ftrace: Fix the misleading comment for arch/x86/kernel/ftrace.c
tracing: Fix crash from reading trace_pipe with sendfile
tracing: Have preempt(irqs)off trace preempt disabled functions
tracing: Fix return while holding a lock in register_tracer()
ftrace: Use kasprintf() in ftrace_profile_tracefs()
ftrace: Update dynamic ftrace calls only if necessary
ftrace: Make ftrace_hash_rec_enable return update bool
tracing: Fix typoes in code comment and printk in trace_nop.c
tracing, writeback: Replace cgroup path to cgroup ino
tracing: Use flags instead of bool in trigger structure
tracing: Add an unreg_all() callback to trigger commands
tracing: Add needs_rec flag to event triggers
tracing: Add a per-event-trigger 'paused' field
tracing: Add get_syscall_name()
tracing: Add event record param to trigger_ops.func()
tracing: Make event trigger functions available
tracing: Make ftrace_event_field checking functions available
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A small set of fixes for the usual ARM/SOC irqchip drivers
- A set of fixes for mbigen to handle multiple devices in a hardware
module proper
- A cleanup for the mbigen config option which was pointlessly user
configurable.
- A cleanup for tegra replacing open coded functionality by the
proper core function
The config cleanup touches arch/arm64/Kconfig.platforms to select the
irq chip for the related platform"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mbigen: Make CONFIG_HISILICON_IRQ_MBIGEN a hidden option
ARM64: Kconfig: Select mbigen interrupt controller on Hisilicon platform
irqchip/mbigen: Handle multiple device nodes in a mbigen module
irqchip/mbigen: Adjust DT bindings to handle multiple devices in a module
irqchip/tegra: Switch to use irq_domain_free_irqs_common
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This tree contains various perf fixes on the kernel side, plus three
hw/event-enablement late additions:
- Intel Memory Bandwidth Monitoring events and handling
- the AMD Accumulated Power Mechanism reporting facility
- more IOMMU events
... and a final round of perf tooling updates/fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
perf llvm: Use strerror_r instead of the thread unsafe strerror one
perf llvm: Use realpath to canonicalize paths
perf tools: Unexport some methods unused outside strbuf.c
perf probe: No need to use formatting strbuf method
perf help: Use asprintf instead of adhoc equivalents
perf tools: Remove unused perf_pathdup, xstrdup functions
perf tools: Do not include stringify.h from the kernel sources
tools include: Copy linux/stringify.h from the kernel
tools lib traceevent: Remove redundant CPU output
perf tools: Remove needless 'extern' from function prototypes
perf tools: Simplify die() mechanism
perf tools: Remove unused DIE_IF macro
perf script: Remove lots of unused arguments
perf thread: Rename perf_event__preprocess_sample_addr to thread__resolve
perf machine: Rename perf_event__preprocess_sample to machine__resolve
perf tools: Add cpumode to struct perf_sample
perf tests: Forward the perf_sample in the dwarf unwind test
perf tools: Remove misplaced __maybe_unused
perf list: Fix documentation of :ppp
perf bench numa: Fix assertion for nodes bitfield
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt2
Merge "First fixes batch for AT91 on 4.6 - DT only fixes" from Nicolas Ferre:
- prevent the boards from having glitches when inserting/removing SD card on
sama5d3/d4 Xplained. The regulators should be kept on.
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- fix hotplug bugs
- fix irq live lock
- fix various topology handling bugs
- fix APIC ACK ordering
- fix PV iopl handling
- fix speling
- fix/tweak memcpy_mcsafe() return value
- fix fbcon bug
- remove stray prototypes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/msr: Remove unused native_read_tscp()
x86/apic: Remove declaration of unused hw_nmi_is_cpu_stuck
x86/oprofile/nmi: Add missing hotplug FROZEN handling
x86/hpet: Use proper mask to modify hotplug action
x86/apic/uv: Fix the hotplug notifier
x86/apb/timer: Use proper mask to modify hotplug action
x86/topology: Use total_cpus not nr_cpu_ids for logical packages
x86/topology: Fix Intel HT disable
x86/topology: Fix logical package mapping
x86/irq: Cure live lock in fixup_irqs()
x86/tsc: Prevent NULL pointer deref in calibrate_delay_is_known()
x86/apic: Fix suspicious RCU usage in smp_trace_call_function_interrupt()
x86/iopl: Fix iopl capability check on Xen PV
x86/iopl/64: Properly context-switch IOPL on Xen PV
selftests/x86: Add an iopl test
x86/mm, x86/mce: Fix return type/value for memcpy_mcsafe()
x86/video: Don't assume all FB devices are PCI devices
arch/x86/irq: Purge useless handler declarations from hw_irq.h
x86: Fix misspellings in comments
|
|
earlyprintk is architecture specific option.
earlycon is generic and small footprint.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
|
|
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Currently we disable preemption in copy_to_user_page; a behaviour that
we inherited from the 32-bit arm code. This was necessary for older
cores without broadcast data cache maintenance, and ensured that cache
lines were dirtied and cleaned by the same CPU. On these systems dirty
cache line migration was not possible, so this was sufficient to
guarantee coherency.
On contemporary systems, cache coherence protocols permit (dirty) cache
lines to migrate between CPUs as a result of speculation, prefetching,
and other behaviours. To account for this, in ARMv8 data cache
maintenance operations are broadcast and affect all data caches in the
domain associated with the VA (i.e. ISH for kernel and user mappings).
In __switch_to we ensure that tasks can be safely migrated in the middle
of a maintenance sequence, using a dsb(ish) to ensure prior explicit
memory accesses are observed and cache maintenance operations are
completed before a task can be run on another CPU.
Given the above, it is not necessary to disable preemption in
copy_to_user_page. This patch removes the preempt_{disable,enable}
calls, permitting preemption.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit 324420bf91f60582 ("arm64: add support for ioremap() block
mappings") added new p?d_set_huge functions which do the hard work to
generate and set a correct block entry.
These differ from open-coded huge page creation in the early page table
code by explicitly setting the P?D_TYPE_SECT bits (which are implicitly
retained by mk_sect_prot() for any valid prot), but are otherwise
identical (and cannot fail on arm64).
For simplicity and consistency, make use of these in the initial page
table creation code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The KASLR code incorrectly expects the contents of x18 to be preserved
across a call into C code, and uses it to stash the contents of SCTLR_EL1
before enabling the MMU. If the MMU needs to be disabled again to create
the randomized kernel mapping, x18 is written back to SCTLR_EL1, which is
likely to crash the system if x18 has been clobbered by kasan_early_init()
or kaslr_early_init(). So use x22 instead, which is not in use so far in
head.S
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Switch to the generic extable search and sort routines which were introduced
with commit a272858 from Ard Biesheuvel. This saves quite some memory in the
vmlinux binary with the 64bit kernel.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
PA-RISC wants to sleep 5 seconds before panicking when panic_on_oops
is set, with no apparent reason. Remove this feature, since some users
may want their systems to fail as quickly as possible.
Users who want to delay reboot after panic can use PANIC_TIMEOUT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The system calls alloc_hugepages() and free_hugepages() were introduced
in Linux 2.5.36 and removed again in 2.5.54. They were never implemented
on parisc, so let's drop them now.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
|
|
After e76b027 ("x86,vdso: Use LSL unconditionally for vgetcpu")
native_read_tscp() is unused in the kernel. The function can be removed like
native_read_tsc() was.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1458687968-9106-1-git-send-email-prarit@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
As a interrupt controller used on some of hisilicon SOCs(660,1610 etc.),
mbigen driver should be enabled when CONFIG_ARCH_HISI is enabled.
Signed-off-by: Ma Jun <majun258@huawei.com>
Cc: mark.rutland@arm.com
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: Catalin.Marinas@arm.com
Cc: guohanjun@huawei.com
Cc: Will.Deacon@arm.com
Cc: huxinwei@huawei.com
Cc: lizefan@huawei.com
Cc: dingtianhong@huawei.com
Cc: zhaojunhua@hisilicon.com
Cc: liguozhu@hisilicon.com
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1458723993-21044-2-git-send-email-majun258@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Merge third patch-bomb from Andrew Morton:
- more ocfs2 changes
- a few hotfixes
- Andy's compat cleanups
- misc fixes to fatfs, ptrace, coredump, cpumask, creds, eventfd,
panic, ipmi, kgdb, profile, kfifo, ubsan, etc.
- many rapidio updates: fixes, new drivers.
- kcov: kernel code coverage feature. Like gcov, but not
"prohibitively expensive".
- extable code consolidation for various archs
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (81 commits)
ia64/extable: use generic search and sort routines
x86/extable: use generic search and sort routines
s390/extable: use generic search and sort routines
alpha/extable: use generic search and sort routines
kernel/...: convert pr_warning to pr_warn
drivers: dma-coherent: use memset_io for DMA_MEMORY_IO mappings
drivers: dma-coherent: use MEMREMAP_WC for DMA_MEMORY_MAP
memremap: add MEMREMAP_WC flag
memremap: don't modify flags
kernel/signal.c: add compile-time check for __ARCH_SI_PREAMBLE_SIZE
mm/mprotect.c: don't imply PROT_EXEC on non-exec fs
ipc/sem: make semctl setting sempid consistent
ubsan: fix tree-wide -Wmaybe-uninitialized false positives
kfifo: fix sparse complaints
scripts/gdb: account for changes in module data structure
scripts/gdb: add cmdline reader command
scripts/gdb: add version command
kernel: add kcov code coverage
profile: hide unused functions when !CONFIG_PROC_FS
hpwdt: use nmi_panic() when kernel panics in NMI handler
...
|
|
Pull more KVM updates from Paolo Bonzini:
"Second round of KVM changes for 4.6:
- build fixes for PPC KVM
- miscellaneous bugfixes for ARM KVM
- cleanup of memory barrier and removal of redundant barriers
- x86 fixes: page tracking oops, support for old buggy KVM nested on 4.5
- support for protection keys in guests
- lockdep fix
- another conversion to simple wait queues and raw spinlocks,
backported from PREEMPT_RT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (27 commits)
KVM: page_track: fix access to NULL slot
KVM: PPC: do not compile in vfio.o unconditionally
kvm, rt: change async pagefault code locking for PREEMPT_RT
KVM/PPC: update the comment of memory barrier in the kvmppc_prepare_to_enter()
KVM/x86: update the comment of memory barrier in the vcpu_enter_guest()
KVM: Replace smp_mb() with smp_load_acquire() in the kvm_flush_remote_tlbs()
KVM/x86: Call smp_wmb() before increasing tlbs_dirty
KVM: Replace smp_mb() with smp_mb_after_atomic() in the kvm_make_all_cpus_request()
KVM/x86: Replace smp_mb() with smp_store_mb/release() in the walk_shadow_page_lockless_begin/end()
KVM: Remove redundant smp_mb() in the kvm_mmu_commit_zap_page()
KVM, pkeys: expose CPUID/CR4 to guest
KVM, pkeys: add pkeys support for permission_fault
KVM, pkeys: introduce pkru_mask to cache conditions
KVM, pkeys: save/restore PKRU when guest/host switches
x86: pkey: introduce write_pkru() for KVM
KVM, pkeys: add pkeys support for xsave state
KVM, pkeys: disable pkeys for guests in non-paging mode
KVM: x86: remove magic number with enum cpuid_leafs
KVM: MMU: return page fault error code from permission_fault
KVM: fix spin_lock_init order on x86
...
|
|
Replace the arch specific versions of search_extable() and
sort_extable() with calls to the generic ones, which now support
relative exception tables as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the arch specific versions of search_extable() and
sort_extable() with calls to the generic ones, which now support
relative exception tables as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the arch specific versions of search_extable() and
sort_extable() with calls to the generic ones, which now support
relative exception tables as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the arch specific versions of search_extable() and
sort_extable() with calls to the generic ones, which now support
relative exception tables as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
kcov provides code coverage collection for coverage-guided fuzzing
(randomized testing). Coverage-guided fuzzing is a testing technique
that uses coverage feedback to determine new interesting inputs to a
system. A notable user-space example is AFL
(http://lcamtuf.coredump.cx/afl/). However, this technique is not
widely used for kernel testing due to missing compiler and kernel
support.
kcov does not aim to collect as much coverage as possible. It aims to
collect more or less stable coverage that is function of syscall inputs.
To achieve this goal it does not collect coverage in soft/hard
interrupts and instrumentation of some inherently non-deterministic or
non-interesting parts of kernel is disbled (e.g. scheduler, locking).
Currently there is a single coverage collection mode (tracing), but the
API anticipates additional collection modes. Initially I also
implemented a second mode which exposes coverage in a fixed-size hash
table of counters (what Quentin used in his original patch). I've
dropped the second mode for simplicity.
This patch adds the necessary support on kernel side. The complimentary
compiler support was added in gcc revision 231296.
We've used this support to build syzkaller system call fuzzer, which has
found 90 kernel bugs in just 2 months:
https://github.com/google/syzkaller/wiki/Found-Bugs
We've also found 30+ bugs in our internal systems with syzkaller.
Another (yet unexplored) direction where kcov coverage would greatly
help is more traditional "blob mutation". For example, mounting a
random blob as a filesystem, or receiving a random blob over wire.
Why not gcov. Typical fuzzing loop looks as follows: (1) reset
coverage, (2) execute a bit of code, (3) collect coverage, repeat. A
typical coverage can be just a dozen of basic blocks (e.g. an invalid
input). In such context gcov becomes prohibitively expensive as
reset/collect coverage steps depend on total number of basic
blocks/edges in program (in case of kernel it is about 2M). Cost of
kcov depends only on number of executed basic blocks/edges. On top of
that, kernel requires per-thread coverage because there are always
background threads and unrelated processes that also produce coverage.
With inlined gcov instrumentation per-thread coverage is not possible.
kcov exposes kernel PCs and control flow to user-space which is
insecure. But debugfs should not be mapped as user accessible.
Based on a patch by Quentin Casasnovas.
[akpm@linux-foundation.org: make task_struct.kcov_mode have type `enum kcov_mode']
[akpm@linux-foundation.org: unbreak allmodconfig]
[akpm@linux-foundation.org: follow x86 Makefile layout standards]
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: syzkaller <syzkaller@googlegroups.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tavis Ormandy <taviso@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Kees Cook <keescook@google.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: David Drysdale <drysdale@google.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add new Port Write handler registration interfaces that attach PW
handlers to local mport device objects. This is different from old
interface that attaches PW callback to individual RapidIO device. The
new interfaces are intended for use for common event handling (e.g.
hot-plug notifications) while the old interface is available for
individual device drivers.
This patch is based on patch proposed by Andre van Herk but preserves
existing per-device interface and adds lock protection for list
handling.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change mport object initialization/registration sequence to match
reworked version of rio_register_mport() in the core code.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This commit fixes the following security hole affecting systems where
all of the following conditions are fulfilled:
- The fs.suid_dumpable sysctl is set to 2.
- The kernel.core_pattern sysctl's value starts with "/". (Systems
where kernel.core_pattern starts with "|/" are not affected.)
- Unprivileged user namespace creation is permitted. (This is
true on Linux >=3.8, but some distributions disallow it by
default using a distro patch.)
Under these conditions, if a program executes under secure exec rules,
causing it to run with the SUID_DUMP_ROOT flag, then unshares its user
namespace, changes its root directory and crashes, the coredump will be
written using fsuid=0 and a path derived from kernel.core_pattern - but
this path is interpreted relative to the root directory of the process,
allowing the attacker to control where a coredump will be written with
root privileges.
To fix the security issue, always interpret core_pattern for dumps that
are written under SUID_DUMP_ROOT relative to the root directory of init.
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
x86's is_compat_task always checked the current syscall type, not the
task type. It has no non-arch users any more, so just remove it to
avoid confusion.
On x86, nothing should really be checking the task ABI. There are
legitimate users for the syscall ABI and for the mm ABI.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sparc's syscall_get_arch was buggy: it returned the task arch, not the
syscall arch. This could confuse seccomp and audit.
I don't think this is as bad for seccomp as it looks: sparc's 32-bit and
64-bit syscalls are numbered the same.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On sparc64 compat-enabled kernels, any task can make 32-bit and 64-bit
syscalls. is_compat_task returns true in 32-bit tasks, which does not
necessarily imply that the current syscall is 32-bit.
Provide an in_compat_syscall implementation that checks whether the
current syscall is compat.
As far as I know, sparc is the only architecture on which is_compat_task
checks the compat status of the task and on which the compat status of a
syscall can differ from the compat status of the task. On x86,
is_compat_task checks the syscall type, not the task type.
[akpm@linux-foundation.org: add comment, per Sam]
[akpm@linux-foundation.org: update comment, per Andy]
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.6:
- Make earlyprintk=xen work for HVM guests
- Remove module support for things never built as modules"
* tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: make platform-pci.c explicitly non-modular
drivers/xen: make sys-hypervisor.c explicitly non-modular
drivers/xen: make xenbus_dev_[front/back]end explicitly non-modular
drivers/xen: make [xen-]ballon explicitly non-modular
xen: audit usages of module.h ; remove unnecessary instances
xen/x86: Drop mode-selecting ifdefs in startup_xen()
xen/x86: Zero out .bss for PV guests
hvc_xen: make early_printk work with HVM guests
hvc_xen: fix xenboot for DomUs
hvc_xen: add earlycon support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- updates for the Exynos IOMMU driver to make use of default domains
and to add support for the SYSMMU v5
- new Mediatek IOMMU driver
- support for the ARMv7 short descriptor format in the io-pgtable code
- default domain support for the ARM SMMU
- couple of other small fixes all over the place
* tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/ipmmu-vmsa: Add r8a7795 DT binding
iommu/mediatek: Check for NULL instead of IS_ERR()
iommu/io-pgtable-armv7s: Fix kmem_cache_alloc() flags
iommu/mediatek: Fix handling of of_count_phandle_with_args result
iommu/dma: Fix NEED_SG_DMA_LENGTH dependency
iommu/mediatek: Mark PM functions as __maybe_unused
iommu/mediatek: Select ARM_DMA_USE_IOMMU
iommu/exynos: Use proper readl/writel register interface
iommu/exynos: Pointers are nto physical addresses
dts: mt8173: Add iommu/smi nodes for mt8173
iommu/mediatek: Add mt8173 IOMMU driver
memory: mediatek: Add SMI driver
dt-bindings: mediatek: Add smi dts binding
dt-bindings: iommu: Add binding for mediatek IOMMU
iommu/ipmmu-vmsa: Use ARCH_RENESAS
iommu/exynos: Support multiple attach_device calls
iommu/exynos: Add Maintainers entry for Exynos SYSMMU driver
iommu/exynos: Add support for v5 SYSMMU
iommu/exynos: Update device tree documentation
iommu/exynos: Add support for SYSMMU controller with bogus version reg
...
|
|
This happens when doing the reboot test from virt-tests:
[ 131.833653] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 131.842461] IP: [<ffffffffa0950087>] kvm_page_track_is_active+0x17/0x60 [kvm]
[ 131.850500] PGD 0
[ 131.852763] Oops: 0000 [#1] SMP
[ 132.007188] task: ffff880075fbc500 ti: ffff880850a3c000 task.ti: ffff880850a3c000
[ 132.138891] Call Trace:
[ 132.141639] [<ffffffffa092bd11>] page_fault_handle_page_track+0x31/0x40 [kvm]
[ 132.149732] [<ffffffffa093380f>] paging64_page_fault+0xff/0x910 [kvm]
[ 132.172159] [<ffffffffa092c734>] kvm_mmu_page_fault+0x64/0x110 [kvm]
[ 132.179372] [<ffffffffa06743c2>] handle_exception+0x1b2/0x430 [kvm_intel]
[ 132.187072] [<ffffffffa067a301>] vmx_handle_exit+0x1e1/0xc50 [kvm_intel]
...
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Fixes: 3d0c27ad6ee465f174b09ee99fcaf189c57d567a
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
