Age | Commit message (Collapse) | Author |
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
|
|
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6ce0 ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
|
|
The recent change to use a pwm lookup table for the ezx machines
was incomplete and only changed the a780 model, but not the
other ones in the same file.
This adds the missing calls to pwm_add_table().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c3322022897c ("ARM: pxa: ezx: Use PWM lookup table")
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "Marvell Berlin fixes for 4.4-rc1 (round 1)" from Sebastian Hesselbarth:
- fix wrong SDIO DT clocks on BG2Q
* tag 'berlin-fixes-for-4.4-rc1-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Merge "Fixes for Exynos" from Krzysztof Kozlowski:
1. Fix potential NULL pointer dereference in Exynos PMU driver.
2. Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
* tag 'samsung-fixes-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a99 ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the selection of the pinctrl driver to SoC family level since we
have two pinctrl drivers. It is useless to select one which is not
compatible with the SoC.
[abelloni: fixed pm.c when only sama2d2 is selected]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
So far, only the bus clock has been assigned, but in reality the
SAI IP has for clock inputs. The driver has been updated to
make use of the additional clock inputs by c3ecef21c3f2 ("ASoC:
fsl_sai: add sai master mode support"). Due to a bug in the
clock tree, the audio clock has been enabled none the less by
the specified bus clock (see "ARM: imx: clk-vf610: fix SAI
clock tree"), which made master mode even without the proper
clock assigned working.
This patch completes the clock definition for SAI2. On Vybrid,
only two MCLK out of the four options are available (the first
being the bus clock itself). See chapter 8.10.1.2.3 of the
Vybrid Reference manual ("SAI transmitter and receiver options
for MCLK selection"). Note: The audio clocks are only required
in master mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On ixp4xx, the readl() function returns an 'unsigned long' output
when indirect I/O is used. This is unlike any other platform, and
it causes lots of harmless compiler warnings, such as:
drivers/ata/libahci.c: In function 'ahci_show_host_version':
drivers/ata/libahci.c:254:22: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_registers':
drivers/block/mtip32xx/mtip32xx.c:2602:31: warning: format '%X' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/cciss.c: In function 'print_cfg_table':
drivers/block/cciss.c:3845:25: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=]
This changes all six of the ixp4xx specific I/O read functions
to return the same types that we have in the normal asm/io.h,
to avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
|
|
Enable REGULATOR_FIXED_VOLTAGE for all OMAP2+ platforms
otherwise system can't boot from SD-card when kernel is
built for single SoC (for example, with CONFIG_SOC_DRA7XX=y only).
It's also required for almost all TI SoC's platforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the missing SPI controller DMA handler in the dm816x DT
node, only properties for the two channels on four were present.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add missing #mbox-cells for dm816x mbox DT node.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
|
|
Pull MIPS fix from Ralf Baechle:
"Just a fix for empty loops that may be removed by non-antique GCC"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix delay loops which may be removed by GCC.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Add missing initialization of max_pfn, which is needed to make
selftests/vm/mlock2-tests succeed,
- Wire up new mlock2 syscall"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up mlock2
m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: m54xx - Add missing initialization of max_pfn
m68k/mm: motorola - Add missing initialization of max_pfn
|
|
Pull ARM fixes from Russell King:
"Just two changes this time around:
- wire up the new mlock2 syscall added during the last merge window
- fix a build problem with certain configurations provoked by making
CONFIG_OF user selectable"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8454/1: OF implies OF_FLATTREE
ARM: wire up mlock2 syscall
|
|
On the ARM architecture, individual platforms select CONFIG_USE_OF if they
need it, but all device tree code is keyed off CONFIG_OF. When building
a platform without DT support and manually enabling CONFIG_OF, we now
get a number of build errors, e.g.
arch/arm/kernel/devtree.c: In function 'setup_machine_fdt':
arch/arm/kernel/devtree.c:215:19: error: implicit declaration of function 'early_init_dt_verify' [-Werror=implicit-function-declaration]
We could now try to separate the use case of booting from DT vs. the
case of using the dynamic implementation, but that seems more complicated
than it can gain us.
This simply changes the ARM Kconfig file to always enable OF_RESERVED_MEM
and OF_EARLY_FLATTREE when CONFIG_OF is enabled. These options add a little
extra code when we just want the dynamic OF implementation, but that seems
like a rather obscure case, and this version solves all CONFIG_OF related
randconfig regressions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0166dc11be91 ("of: make CONFIG_OF user selectable")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
and three for HiSilicon and DesignWare host controllers.
Summary:
NUMA:
- Prevent out of bounds access in numa_node override (Mathias Krause)
HiSilicon host bridge driver:
- Fix deferred probing (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect io_base assignment (Stanimir Varbanov)
- Move align_resource function pointer to pci_host_bridge structure
(Gabriele Paoloni)"
* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
PCI: hisi: Fix deferred probing
PCI: designware: Remove incorrect io_base assignment
PCI: Prevent out of bounds access in numa_node override
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a small backlog of at91 patches here, the most significant is
the addition of some sama5d2 Xplained nodes that were waiting on an
MFD include file to get merged through another tree.
We normally try to sort those out before the merge window opens, but
the maintainer wasn't aware of that here and I decided to merge the
changes this time as an exception.
On OMAP a series of audio changes for dra7 missed the merge window but
turned out to be necessary to fix a boot time imprecise external abort
error and to get audio working.
The other changes are the usual simple changes, here is a list sorted
by platform:
at91:
removal of a useless defconfig option
removal of some legacy DT pieces
use of the proper watchdog compatible string
update of the MAINTAINERS entries for some Atmel drivers
drivers/scpi:
hide get_scpi_ops in module from built-in code
imx:
add missing .irq_set_type for i.MX GPC irq_chip.
fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
fix a merge error in Vybrid dts regarding to ADC device property
keystone:
fix the optional PDSP firmware loading
fix linking RAM setup for QMs
fix crash with clk_ignore_unused
mediatek:
Enable SCPSYS power domain driver by default
mvebu:
fix QNAP TS219 power-off in dts
fix legacy get_irqnr_and_base for dove and orion5x
omap:
fix l4 related boot time errors for dm81xx
use lockless cldm/pwrdm api in omap4_boot_secondary
remove t410 abort handler to avoid hiding other critical errors
mark cpuidle tracepoints as _rcuidle
fix module alias for omap-ocp2scp
pxa:
palm: Fix typos in PWM lookup table code
renesas:
missing __initconst annotation for r8a7793_boards_compat_dt
rockchip:
disable mmc-tuning on the veyron-minnie board
adding the init state for the over-temperature-protection
zx:
only build power domain code when CONFIG_PM=y"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: orion5x: Fix legacy get_irqnr_and_base
ARM: dove: Fix legacy get_irqnr_and_base
soc: Mediatek: Enable SCPSYS power domain driver by default
ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
soc: ti: use request_firmware_direct() as acc firmware is optional
ARM: imx: add platform irq type setting in gpc
ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
ARM: shmobile: r8a7793: proper constness with __initconst
scpi: hide get_scpi_ops in module from built-in code
ARM: zx: only build power domain code when CONFIG_PM=y
ARM: pxa: palm: Fix typos in PWM lookup table code
ARM: dts: Kirkwood: Fix QNAP TS219 power-off
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
MAINTAINERS: Atmel drivers: change NAND and ISI entries
ARM: at91/dt: sama5d2 Xplained: add several devices
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Build fix when !CONFIG_UID16 (the patch is touching generic files but
it only affects arm64 builds; submitted by Arnd Bergmann)
- EFI fixes to deal with early_memremap() returning NULL and correctly
mapping run-time regions
- Fix CPUID register extraction of unsigned fields (not to be
sign-extended)
- ASID allocator fix to deal with long-running tasks over multiple
generation roll-overs
- Revert support for marking page ranges as contiguous PTEs (it leads
to TLB conflicts and requires additional non-trivial kernel changes)
- Proper early_alloc() failure check
- Disable KASan for 48-bit VA and 16KB page configuration (the pgd is
larger than the KASan shadow memory)
- Update the fault_info table (original descriptions based on early
engineering spec)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: efi: fix initcall return values
arm64: efi: deal with NULL return value of early_memremap()
arm64: debug: Treat the BRPs/WRPs as unsigned
arm64: cpufeature: Track unsigned fields
arm64: cpufeature: Add helpers for extracting unsigned values
Revert "arm64: Mark kernel page ranges contiguous"
arm64: mm: keep reserved ASIDs in sync with mm after multiple rollovers
arm64: KASAN depends on !(ARM64_16K_PAGES && ARM64_VA_BITS_48)
arm64: efi: correctly map runtime regions
arm64: mm: fix fault_info table xFSC decoding
arm64: fix building without CONFIG_UID16
arm64: early_alloc: Fix check for allocation failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"nios2: fix cache coherency"
* tag 'nios2-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: fix cache coherency
|
|
GCC 4.1 and newer remove empty loops. This becomes a problem when delay
loops get removed. Fixed by rewriting to user the proper Linux interface
for such delays.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: John Crispin <blogic@openwrt.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fix for perf callgraph unwinding causing RCU stalls
- Fix to enable Linux to run on non-default Interrupt priority 0
- Removal of pointless SYNC from __switch_to()
* tag 'arc-4.4-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: dw2 unwind: Remove falllback linear search thru FDE entries
ARC: remove SYNC from __switch_to()
ARCv2: Use the default irq priority for idle sleep
ARC: Abstract out ISA specific SLEEP args
ARC: comments update
ARC: switch to arc-linux- CROSS_COMPILE prefix across all configs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: devicetree fixes for 4.4" from Heiko Stuebner:
Two fixes to Rockchip devicetree files, disabling the mmc-tuning
on the veyron-minnie board for now and adding the init state for
the over-temperature-protection to prevent glitches making the
system reboot sometimes.
* tag 'v4.4-rockchip-dts32-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
|
|
Merge "mvebu fixes for 4.4 (part 1)" from Jason Cooper:
- Fix QNAP TS219 power-off in dts
- Fix legacy get_irqnr_and_base for dove and orion5x
* tag 'mvebu-fixes-4.4-1' of git://git.infradead.org/linux-mvebu:
ARM: orion5x: Fix legacy get_irqnr_and_base
ARM: dove: Fix legacy get_irqnr_and_base
ARM: dts: Kirkwood: Fix QNAP TS219 power-off
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.4" from Simon Horman:
* r8a7793 SoC: Annotate r8a7793_boards_compat_dt with __initconst
Aside from being correct this builds that otherwise
fail with section mismatch errors.
* tag 'renesas-fixes-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7793: proper constness with __initconst
|
|
s3c2410_plls_add is a device notifier that may be called at runtime and
is correctly not marked __init. However it calls s3c_plltab_register()
which is marked __init, and that triggers a build error when we are
checking for section mismatches:
WARNING: vmlinux.o(.text+0x195e0): Section mismatch in reference from the function s3c2410_plls_add() to the function .init.text:s3c_plltab_register()
The function s3c2410_plls_add() references
the function __init s3c_plltab_register().
This is often because s3c2410_plls_add lacks a __init
annotation or the annotation of s3c_plltab_register is wrong.
This removes the __init annotation from s3c2410_plls_add as well as the
__initdata section annotations from s3c2440_plls_12 and s3c2440_plls_169344,
which in turn are referenced from s3c2410_plls_add.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix gntdev and numa balancing.
- Fix x86 boot crash due to unallocated legacy irq descs.
- Fix overflow in evtchn device when > 1024 event channels.
* tag 'for-linus-4.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: dynamically grow pending event channel ring
xen/events: Always allocate legacy interrupts on PV guests
xen/gntdev: Grant maps should not be subject to NUMA balancing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- tm: Block signal return from setting invalid MSR state from Michael
Neuling
- tm: Check for already reclaimed tasks from Michael Neuling
* tag 'powerpc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/tm: Check for already reclaimed tasks
powerpc/tm: Block signal return setting invalid MSR state
|
|
Even though initcall return values are typically ignored, the
prototype is to return 0 on success or a negative errno value on
error. So fix the arm_enable_runtime_services() implementation to
return 0 on conditions that are not in fact errors, and return a
meaningful error code otherwise.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add NULL return value checks to two invocations of early_memremap()
in the UEFI init code. For the UEFI configuration tables, we just
warn since we have a better chance of being able to report the issue
in a way that can actually be noticed by a human operator if we don't
abort right away. For the UEFI memory map, however, all we can do is
panic() since we cannot proceed without a description of memory.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
IDAA64DFR0_EL1: BRPs and WRPs are unsigned values. Use
the appropriate helpers to extract those fields.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Some of the feature bits have unsigned values and need
to be treated accordingly to avoid errors. Adds the property
to the feature bits and use the appropriate field extract helpers.
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
After commit 8c058b0b9c34 ("x86/irq: Probe for PIC presence before
allocating descs for legacy IRQs") early_irq_init() will no longer
preallocate descriptors for legacy interrupts if PIC does not
exist, which is the case for Xen PV guests.
Therefore we may need to allocate those descriptors ourselves.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
The cpuid_feature_extract_field() extracts the feature value
as a signed integer. This could be problematic for features
whose values are unsigned. e.g, ID_AA64DFR0_EL1:BRPs. Add
an unsigned variant for the unsigned fields.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This reverts commit 348a65cdcbbf243073ee39d1f7d4413081ad7eab.
Incorrect page table manipulation that does not respect the ARM ARM
recommended break-before-make sequence may lead to TLB conflicts. The
contiguous PTE patch makes the system even more susceptible to such
errors by changing the mapping from a single page to a contiguous range
of pages. An additional TLB invalidation would reduce the risk window,
however, the correct fix is to switch to a temporary swapper_pg_dir.
Once the correct workaround is done, the reverted commit will be
re-applied.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
|
|
Under some unusual context-switching patterns, it is possible to end up
with multiple threads from the same mm running concurrently with
different ASIDs:
1. CPU x schedules task t with mm p containing ASID a and generation g
This task doesn't block and the CPU doesn't context switch.
So:
* per_cpu(active_asid, x) = {g,a}
* p->context.id = {g,a}
2. Some other CPU generates an ASID rollover. The global generation is
now (g + 1). CPU x is still running t, with no context switch and
so per_cpu(reserved_asid, x) = {g,a}
3. CPU y schedules task t', which shares mm p with t. The generation
mismatches, so we take the slowpath and hit the reserved ASID from
CPU x. p is then updated so that p->context.id = {g + 1,a}
4. CPU y schedules some other task u, which has an mm != p.
5. Some other CPU generates *another* CPU rollover. The global
generation is now (g + 2). CPU x is still running t, with no context
switch and so per_cpu(reserved_asid, x) = {g,a}.
6. CPU y once again schedules task t', but now *fails* to hit the
reserved ASID from CPU x because of the generation mismatch. This
results in a new ASID being allocated, despite the fact that t is
still running on CPU x with the same mm.
Consequently, TLBIs (e.g. as a result of CoW) will not be synchronised
between the two threads.
This patch fixes the problem by updating all of the matching reserved
ASIDs when we hit on the slowpath (i.e. in step 3 above). This keeps
the reserved ASIDs in-sync with the mm and avoids the problem.
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
On KASAN + 16K_PAGES + 48BIT_VA
arch/arm64/mm/kasan_init.c: In function ‘kasan_early_init’:
include/linux/compiler.h:484:38: error: call to ‘__compiletime_assert_95’ declared with attribute error: BUILD_BUG_ON failed: !IS_ALIGNED(KASAN_SHADOW_END, PGDIR_SIZE)
_compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
Currently KASAN will not work on 16K_PAGES and 48BIT_VA, so
forbid such configuration to avoid above build failure.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Suzuki K. Poulose <Suzuki.Poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
There is intermittent cache coherency issue caught in toolchian tests.
Revert to use flushd.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omaps for v4.4-rc cycle" from Tony Lindgren:
- A series of audio changes for dra7 that missed the merge window but turned
out to be necessary to fix a boot time imprecise external abort error and to
getaudio working
- Fix l4 related boot time errors for dm81xx
- Use lockless cldm/pwrdm api in omap4_boot_secondary
- Remove t410 custom abort handler that is no longer needed and may
hide other critical errors
- Mark cpuidle tracepoints as _rcuidle
- Fix module alias for omap-ocp2scp
* tag 'omap-for-v4.4/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: OMAP2+: remove custom abort handler for t410
ARM: OMAP: DRA7: hwmod: Add data for McASP3
ARM: OMAP2+: hwmod: Add hwmod flag for HWMOD_OPT_CLKS_NEEDED
ARM: dts: dra7: Fix McASP3 node regarding to clocks
bus: omap-ocp2scp: Fix module alias
ARM: OMAP2+: PM: Denote the cpuidle tracepoints as _rcuidle()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes
Merge "Few Keystone fixes for 4.4-rcx" from Santosh Shilimkar:
- Fix the optional PDSP firmware loading
- Fix linking RAM setup for QMs
- Fix crash with clk_ignore_unused
* tag 'keystone-fixes-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
soc: ti: use request_firmware_direct() as acc firmware is optional
|
|
Linux 4.4-rc2 is backmerged from the keystone fixes.
|