| Age | Commit message (Collapse) | Author |
|---|
|
Merge "ARM: mvebu: DT changes for v3.17 (round 2)" from Jason Cooper:
mvebu DT changes for v3.17 (round 2):
- kirkwood
* Add d2 Network v2 board
- mvebu
* Add Armada 375 ethernet node
* Add CA9 MPcore SoC controller node
* Add support for dynamic freq scaling on Armada XP
* tag 'mvebu-dt-3.17-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: update Armada XP DT for dynamic frequency scaling
ARM: mvebu: add CA9 MPcore SoC Controller node
ARM: mvebu: Enable the network controller in Armada 375 DB board
ARM: mvebu: Add support for the network controller in Armada 375 SoC
ARM: Kirkwood: add DT support for d2 Network v2
ARM: Kirkwood: allow to use netxbig DTSI for d2net_v2 DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Merge "ARM: mvebu: DT changes for v3.17" from Jason Cooper:
mvebu DT changes for v3.17
- kirkwood
* add boards net2big and net5big
- dove
* add vendor prefix for SolidRun
* split CuBox into it's variants
* tag 'mvebu-dt-3.17' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: fix net5big regulator gpio assignments
ARM: dts: mvebu: split SolidRun CuBox into variants
dt-binding: add vendor prefix for SolidRun
ARM: Kirkwood: Add DT descriptions for net2big and net5big.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.17" from Kukjin Kim:
exynos3250: add i2s dt for audio interface
exynos4
- cleanup arm-pmu node because of 4 pmu on
exynos4412 but 2 pmu on other exynos4 SoCs
- add support sub-nodes to exynos usb host for exynos4
exynos4412-odroid-common
- fix T-FLASH hotplug detection
- disable 'always on' for BUCK8
- add support for GPIO based buttons
- add MAX98090 audio codec
exynos4412-odroidx2 and exynos4412-odroidu3
- refactor exynos4412-odroidx and exynos4412-odroid-common
for odroid-x2 and u2/u3
exynos4412-odroidx
- add support for USB phy, host and device
- enable common hardware blocks, secure firmware calls,
watchdog, g2d and fimc (mem2mem) multimedia accelerators
- add support for USB phy, host and device
- correct memory size
exynos5410
- fill in CPU clock-frequency property to avoid warning
exynos5420
- remove display pd because of instability
exynos5420-peach-pit and exynos5800-peach-pi
- sort nodes each other to check its differences easily
- enable audio support and add sound-card name property
- add mask-tpm-reset node
- add cros_ec including keyboard, i2c tunnel and tps65090
and battery under the i2c tunnel
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add I2S dt node for exynos3250
ARM: dts: Add cros_ec to exynos5420-peach-pit and exynos5800-peach-pi
ARM: dts: clean up arm-pmu node for exynos4
ARM: dts: remove display power domain for exynos5420
ARM: dts: Add sound nodes for Odroid-X2/U3 boards
ARM: dts: fix T-FLASH hotplug detection for exynos4412-odroid-common
ARM: dts: add support for GPIO buttons for exynos4412-odroid
ARM: dts: disable 'always on' for BUCK8 regulator for exynos4412-odroid-common
ARM: dts: refactor Odroid DTS file and add support for Odroid X2 and U2/U3
ARM: dts: correct memory size for exynos4412-odroidx
ARM: dts: add support for USB phy, host and device for exynos4412-odroidx
ARM: dts: enable common hardware blocks for exynos4412-odroidx
ARM: dts: add port sub-nodes to exynos usb host modules for exynos4
ARM: dts: Add mask-tpm-reset node in exynos5800-peach-pi
ARM: dts: Add mask-tpm-reset node in exynos5420-peach-pit
ARM: dts: Add sound-card name for Snow/Peach-Pit/Peach-Pi
ARM: dts: Fill in CPU clock-frequency for exynos5410
ARM: dts: Sort nodes within Peach-pit/Peach-pi dts files
ARM: dts: Enable audio support for exynos5800-peach-pi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: device tree changes for 3.17" from Thierry Reding:
- New board support:
* Apalis T30
- HDA support for Tegra124 and Venice2
- Display on Medcom Wide and Roth
- GK20A support on Tegra124
- XUSB pad controller for Tegra124 and Jetson TK1
- Various cleanups
This pulls in the for-3.17/fuse-move, for-3.17/dt-cros-ec-kbd and
for-3.17/xusb-padctl branches to resolve dependencies.
Note that the Apalis T30 support has a runtime dependency on the
for-3.17/pcie-regulators branch, so they should preferably be applied
in that order. I didn't merge that branch into this because Apalis T30
support is new, therefore can't regress, and because the dependency
exists only at runtime.
* tag 'tegra-for-3.17-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
ARM: tegra: roth: add display DT node
ARM: tegra: Fix typoed ams,ext-control properties
ARM: tegra: jetson-tk1: Add XUSB pad controller
ARM: tegra: tegra124: Add XUSB pad controller
ARM: tegra: add GK20A GPU to Tegra124 DT
ARM: tegra: of: add GK20A device tree binding
ARM: tegra: roth: enable input on mmc clock pins
ARM: tegra: roth: fix unsupported pinmux properties
ARM: tegra: Migrate Apalis T30 PCIe power supply scheme
ARM: tegra: tamonten: add the display to the Medcom Wide
ARM: tegra: tamonten: add the base board regulators
ARM: tegra: initial support for apalis t30
ARM: tegra: jetson-tk1: mark eMMC as non-removable
ARM: tegra: venice2 - Enable HDA
ARM: tegra: Add Tegra124 HDA support
ARM: tegra: Add the EC i2c tunnel to tegra124-venice2
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT additions for 3.17" from Maxime Ripard:
Among the few patches that we have so far, there's a few noticeable changes:
- Introduction of the Allwinner A23 SoC
- Support for the GMAC on the A31. This is only available so far on the
boards which bootloader enable the PHY regulator.
- Addition of the infrared receiver
* tag 'sunxi-dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (22 commits)
ARM: dts: sun6i: Add Merrii A31 Hummingbird support
ARM: dts: sun6i: Add ethernet alias for GMAC
ARM: dts: sun6i: Add A31 GMAC gigabit ethernet controller node
ARM: dts: sun6i: Add GMAC clock node to the A31 dtsi
ARM: dts: sun6i: Add pin muxing options for GMAC
ARM: sun8i: Add PRCM clock and reset controller nodes to the DTSI
ARM: sun8i: Add reset controller nodes to the DTSI
ARM: sun8i: Add basic clock nodes to the DTSI
ARM: dts: sun4i: Add ir node to various boards
ARM: dts: sun4i: Add ir controller nodes and pinmux
ARM: dts: sun4i: Add new ba10-tvbox board
ARM: dts: sun7i: Add board support for LinkSprite pcDuino V3
ARM: dts: sun7i: Add ir receiver support to a20-i12-tvbox
ARM: dts: sun7i: Rename sun7i-a20-ir to sun4i-a10-ir
ARM: dts: sun7i: Add AXP209 support to various boards
ARM: dts: sun4i: Add AXP209 support to various boards
ARM: dts: sunxi: Add #interrupt-cells to pinctrl nodes
ARM: sun8i: dt: Add Ippo-q8h v5 support
ARM: sunxi: Add Allwinner A23 dtsi
ARM: sunxi: Add IR controllers on A20 to dtsi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree updates for 3.17" from Shawn Guo:
The i.MX device tree updates for 3.17:
- Add device tree sources and pin function header for i.MX6SX SoC
- Initial imx6sx-sdb board support with FEC, MMC, USB, PMIC, Audio
and GPIO key enabled
- New board support: mbimxsd25 and mbimxsd27 from Eukrea, aristainetos
imx6dl boards, Rex Pro and Basic, Ka-Ro TX6
- Restructure imx6qdl-wandboard.dtsi for new rev C1 board
- Split M28EVK and M53EVK into SoM and EVK parts
- A few correction around SDMA, SSI and SATA device nodes
- Add eSATA support for Cubox-i board
- Updates on edmqmx6 to enable PCIe, I2C and CAN
- Use DT macro for clock ID for imx27 and imx6qdl
- Add FlexCAN support for VF610 SoC
* tag 'imx-dt-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (125 commits)
ARM: dts: vf610: add FlexCAN node
ARM: dts: add initial Rex Basic board support
ARM: dts: add initial Rex Pro board support
ARM: dts: mx5: Split M53EVK into SoM and EVK parts
ARM: dts: imx6: RIoTboard explicitly define pad settings
ARM: dts: vf610: fix length of eshdc1 register property
ARM: dts: Restructure imx6qdl-wandboard.dtsi for new rev C1 board.
ARM: dts: imx53: correct clock-names of SATA node
ARM: imx6: Align ssi nodes between mx6 variants
ARM: i.MX27 clk: dts: Use clock defines in DTS files
ARM: dts: imx: correct sdma compatbile for imx6sl and imx6sx
ARM: dts: imx6sx-sdb: Add audio support
ARM: dts: imx6sx: Pass the fsl,fifo-depth property
ARM: dts: imx6sx: Fix sdma node
ARM: dts: imx6: edmqmx6: Add can bus
ARM: dts: imx6: edmqmx6: Add two other i2c buses
ARM: dts: imx6: edmqmx6: Add PCIe support
ARM: dts: imx25-pdk: Add USB OTG support
ARM: dts: i.MX53: add aipstz nodes
ARM: dts: mxs: Split M28EVK into SoM and EVK parts
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "Keystone DTS update for 3.17" from Santosh Shilimkar:
Keystone DTS update for 3.17
- Ethernet clock tree fix.
- MDIO device tree node. Respective driver update is already queued.
- Ethernet phy node. Respective driver update is already queued.
* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-evm: add 1g ethernet phys nodes
ARM: dts: keystone: add mdio devices entries
ARM: dts: keystone: fix netcp's clocks definitions
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v3.17 merge window, part1" from Tony Lindgren:
First set of .dts changes for omaps for v3.17 merge window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
* tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (43 commits)
ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
ARM: dts: dra7: Add dt data for PCIe controller
ARM: dts: dra7: Add dt data for PCIe PHY
ARM: dts: dra7: Add dt data for PCIe PHY control module
ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
ARM: dts: dra7-evm: Add regulator information to USB2 PHYs
ARM: omap2plus_defconfig: enable TPS65218 configs
ARM: dts: AM437x: Add TPS65218 device tree nodes
ARM: dts: AM437x: Fix i2c nodes indentation
ARM: dts: AM43x: Add TPS65218 device tree nodes
ARM: dts: Add devicetree for Gumstix Pepper board
ARM: dts: dra7: add crossbar device binding
ARM: dts: dra7: add routable-irqs property for gic node
ARM: OMAP24xx: clock: remove legacy clock data
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Third Round of Renesas ARM Based SoC DT Updates for v3.17" from Simon
Horman:
* Initialise SCI using DT when booting the kzm9g, armadillo800eva,
ape6evm and bockw boards without legacy-C code.
* tag 'renesas-dt3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (24 commits)
ARM: shmobile: kzm9g-reference: Initialise SCIF device using DT
ARM: shmobile: sh73a0: Add SCIF nodes
ARM: shmobile: armadillo800eva-reference: Initialise SCIF device using DT
ARM: shmobile: r8a7740: Add SCIF nodes
ARM: shmobile: ape6evm-reference: Initialise SCIF device using DT
ARM: shmobile: r8a73a4: Add SCIF nodes
ARM: shmobile: bockw-reference: Initialise SCIF device using DT
ARM: shmobile: r8a7778: Add SCIF nodes
ARM: shmobile: sh73a0: add SCI clock support for DT
ARM: shmobile: r8a7740: correct SCI clock support for DT
ARM: shmobile: r8a73a4: add SCI clock support for DT
ARM: shmobile: r8a7778: add SCI clock support for DT
ARM: shmobile: r8a7790: lager: use iic cores instead of i2c
ARM: shmobile: Lager: Correct I2C bus for VDD MPU regulator
ARM: shmobile: kzm9g-reference: Remove early_printk from command line
ARM: shmobile: armadillo800eva-reference: Remove early_printk from command line
ARM: shmobile: r8a7779: Consistently use tabs for indentation
ARM: shmobile: henninger: Consistently use tabs for indentation
ARM: shmobile: henninger: enable internal PCI
ARM: shmobile: koelsch: enable internal PCI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds support for the A31 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=172
The Merrii A31 Hummingbird is a development board based on the
Allwinner A31 SoC with multiple USB ports through a USB hub chip,
a uSD slot, a 10/100/1000M ethernet port, an AP6210 WiFi/BT chip,
TV-in, HDMI, VGA, audio in/out ports, and LCD/CSI headers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: enable usbphy, ehci0, ohci0 for on-board usb hub;
add pcf8563 rtc node; add comments for i2c0 and mmc0 pull-ups;
correct ethernet phy address to 0x01; drop uart2 (BT chip has
no power) and uart3 (no device); use proper commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Alias GMAC as ethernet0 so U-boot can fill in the MAC address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A31 has the same GMAC found on the A20 SoC, except it has
an extra reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A31 SoC has a GMAC gigabit ethernet controller supporting
MII, GMII, RGMII modes. Add pin muxing options for these modes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch add I2S (Inter-IC Sound) dt node which supports 1-port
stereo (1 channels) IIS-bus for audio interface with DMA-based
operation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Tested-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This adds cros_ec to exynos5420-peach-pit and exynos5800-peach-pi,
including:
* The keyboard
* The i2c tunnel
* The tps65090 under the i2c tunnel
* The battery under the i2c tunnel
To add extra motivation, it should be noted that tps65090 is one of
the things needed to get display-related FETs turned on for pit and
pi.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch cleans a arm-pmu node up for exynos4. Only exynos4412 series
boards have four pmu interrupts. Rest of exynos4 boards, except 4412, have only
two pmu interrupts. Thus, we can define two interrupts in the
exynos4.dtsi and extends the interrupts only exynos4412.dtsi.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add FlexCAN node for the two FlexCAN IP instances in Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add initial Rex Pro i.mx6dl board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with
cat zImage imx6dl-rex-basic.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with
cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This patch splits the M53EVK device tree file into a common SoM
part and an EVK part. This is needed to make it easier for users
of the SoM to put it into different, non-reference baseboard.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Instead of relying on defaults or bootloader settings, explicitly define
all pad settings.
This resolves reported issues of no analogue audio output.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The rev C1 Wandboard uses the Broadcom 4330 for WiFi and Bluetooth instead of
the 4329. This changes the PADS assigned for the control lines. Another
side effect of the change is that on the rev C1 board, usdhc driver can't
detect the chip presence correctly so usdhc2 now needs its 'non-removeable'
property removed.
So that rev B1 and earlier can continue to work, this patch splits the
board-specific definitions from imx6qdl-wandboard.dtsi into
imx6qdl-wandboard-revb1.dtsi and imx6qdl-wandboard-revc1.dtsi. The new files
include the original base imx6qdl-wandboard.dtsi which retains the common
definitions.
The existing imx6dl-wandboard.dts includes imx6qdl-wandboard-revc1.dtsi and
imx6dl-wandboard-revb1.dts (new) includes imx6qdl-wandboard-revb1.dtsi.
This makes the rev C1 board the new default. The same pattern is used for
imx6q-wandboard.dts.
So, from U-Boot on a WB-Quad you use imxq-wandboard-revb1.dtb for the older B1
board and imxq-wandboard.dtb for the current rev C1 board.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Per the binding doc imx-sata.txt, the first entry of clock-names should
be "sata" than anything else. Correct it for imx53 SATA node.
It works for now only because SATA driver gets clock by index so far.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Since commit 98ea6ad2edd2 (ARM: dts: imx6: use imx51-ssi) the mx6 ssi is
compatible with imx51, so align all the mx6 variant ssi compatible strings as:
compatible = "fsl,<imx6-soc>-ssi", "fsl,imx51-ssi";
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Use clock definitions in i.MX27 DTS files.
Additional changes included in this patch (imx27.dtsi):
- Fix IPG clock for UART6.
- Use EMI_AHB_GATE clock for WEIM.
- Added GPIO_IPG_GATE clock for GPIO nodes. Currently this clock is
not used by the driver, but it can be added in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The SDMA on imx6sl and imx6sx is more compatible with imx6q one than
imx35. Let's use "fsl,imx6q-sdma" instead of "fsl,imx35-sdma", so that
SDMA ROM script on imx6sl and imx6sx can work for audio driver just like
the case of imx6q.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Robin Gong <yibin.gong@freescale.com>
|
|
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Like the other mx6 variants, we need to pass fsl,fifo-depth property in dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Use the correct compatible string for sdma and also provide the sdma firmware
path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add support for the PCI express bus available on MX6 Data Modul
edm-qmx6 board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Tested by loading the g_ether module and doing a ping between mx25pdk and the
host PC via USB.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The AHB to IP bridges (AIPSTZ) allow fine grained access rights management.
Add both bridges to the DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This patch splits the M28EVK device tree file into a common SoM
part and an EVK part. This is needed to make it easier for users
of the SoM to put it into different, non-reference baseboard.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Without that fix, the board freeze during boot.
This appeared after the following commit:
496f065 ARM: i.MX: Use of_clk_get_by_name() for timer clocks for DT case.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:
imx-keypad 20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@02000000/kpp@020b8000
imx-keypad 20b8000.kpp: failed to build keymap
imx-keypad: probe of 20b8000.kpp failed with error -2
Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Spread-spectrum doesn't work with Cubox-i hardware. eSATA devices are
detected, but then fail on normal IO. Therefore, disable this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add the transmit level, boost and attenuation parameters necessary for
the eSATA interface on Cubox-i to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Fix usbmisc compatible string so that usbmisc node can be found and USB
functionality can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The imx6sx iomuxc-gpr syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sx iomuxc-gpr syscon node.
This is necessary to enable SW workaround for ERR007265,
please refer to imx6_pm_common_init of arch/arm/mach-imx/pm-imx6.c
for detail.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Switch to use DT macro for clock ID, so that device tree source is more
readable.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This patch adds support for imx6sx-sdb board's gpio keys:
SW4(FUNC1): KEY_VOLUMEUP
SW5(FUNC2): KEY_VOLUMEDOWN
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This patch add support for the imx6dl based aristainetos board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
DRAM: 1 GiB
NAND: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
