| Age | Commit message (Collapse) | Author |
|---|
|
Supply top level nodes for the STiH407 based development boards.
The Pinctrl configuration has already been applied, so the only
missing piece of the DT puzzle is for a board's DTB to enable
the nodes.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The USB3 controller is present on the b2199 board, so enable
it in the board specific DT file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
STiH418 miphy28lp port0/1 need the oscillator clock configured in the same way
as on STiH407/STiH410 platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The USB3 controller is present on both variants of the b2120 board so
enable the controller in the generic stihxxx-b2120.dtsi file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Now that both usb2 and usb3 phy drivers, and also the ST dwc3 glue code
are all present upstream, we can add the dwc3 DT node and have a working
usb3 controller on stih407-b2120 and stih410-b2020.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Ths picophyreset is incorrectly defined, which stops the usb2 phy being
taken out of reset.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Now that the miphy28lp is upstream, we can add the sata dt nodes
for stih407 family silicon. This has been tested on b2120 board
J4 (sata0 channel). These nodes are disabled by default as a
special mini pci-e to sata daughter board is required which
isn't shipped with the board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
This will avoid programming the retime registers when not implemented
- PIO5 : no retime registers assigned to pins 6 and 7
- PIO35 : pin 7 is reserved so no retime register assigned to it
Signed-off-by: Karim BEN BELGACEM <karim.ben-belgacem@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
On current ST platforms the LPC controls a number of functions. This
patch enables support for the LPC Watchdog and LPC RTC devices on LPC1
and LPC2 respectively.
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Add dt nodes to enable sdhci / eMMC for stih418-b2199 board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The nodes have been split to allow as much commonality as possible.
The stih407 has a silicon bug with eMMC UHS modes (with top regs)
and as such doesn't have any of the uhs dt properties.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The Synchronous Serial Controller is used to provide SPI.
These are the ports which are located on the Stand-By Controller (SBC).
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
The Synchronous Serial Controller is used to provide SPI.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.
Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.
This was exposed by a recent vDSO cleanup.
Fixes: e7d6eefaaa44 x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
|
|
Pull crypto fixes from Herbert Xu:
"This push fixes a build problem with img-hash under non-standard
configurations and a serious regression with sha512_ssse3 which can
lead to boot failures"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
crypto: x86/sha512_ssse3 - fixup for asm function prototype change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- fix for mm_dec_nr_pmds() from Scott.
- fixes for oopses seen with KVM + THP from Aneesh.
- build fixes from Aneesh & Shreyas.
* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
powerpc/mm/thp: Return pte address if we find trans_splitting.
powerpc/mm/thp: Make page table walk safe against thp split/collapse
KVM: PPC: Remove page table walk helpers
KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()
|
|
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
|
|
Pull slave-dmaengine updates from Vinod Koul:
- new drivers for:
- Ingenic JZ4780 controller
- APM X-Gene controller
- Freescale RaidEngine device
- Renesas USB Controller
- remove device_alloc_chan_resources dummy handlers
- sh driver cleanups for peri peri and related emmc and asoc patches
as well
- fixes and enhancements spread over the drivers
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (59 commits)
dmaengine: dw: don't prompt for DW_DMAC_CORE
dmaengine: shdmac: avoid unused variable warnings
dmaengine: fix platform_no_drv_owner.cocci warnings
dmaengine: pch_dma: fix memory leak on failure path in pch_dma_probe()
dmaengine: at_xdmac: unlock spin lock before return
dmaengine: xgene: devm_ioremap() returns NULL on error
dmaengine: xgene: buffer overflow in xgene_dma_init_channels()
dmaengine: usb-dmac: Fix dereferencing freed memory 'desc'
dmaengine: sa11x0: report slave capabilities to upper layers
dmaengine: vdma: Fix compilation warnings
dmaengine: fsl_raid: statify fsl_re_chan_probe
dmaengine: Driver support for FSL RaidEngine device.
dmaengine: xgene_dma_init_ring_mngr() can be static
Documentation: dma: Add documentation for the APM X-Gene SoC DMA device DTS binding
arm64: dts: Add APM X-Gene SoC DMA device and DMA clock DTS nodes
dmaengine: Add support for APM X-Gene SoC DMA engine driver
dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver
dmaengine: renesas,usb-dmac: Add device tree bindings documentation
dmaengine: edma: fixed wrongly initialized data parameter to the edma callback
dmaengine: ste_dma40: fix implicit conversion
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
|
|
Pull ARM fixes from Russell King:
"A few fixes for the recently merged development updates:
- the update to convert a code branch in the procinfo structure
forgot to update the nommu code.
- VDSO only supported for V7 CPUs and later.
- VDSO build creates files which should be ignored by git but are not.
- ensure that make arch/arm/vdso/ doesn't build if it isn't enabled"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8344/1: VDSO: honor CONFIG_VDSO in Makefile
ARM: 8343/1: VDSO: add build artifacts to .gitignore
ARM: Fix nommu booting
ARM: 8342/1: VDSO: depend on CPU_V7
|
|
Pull arch/nios2 updates from Ley Foon Tan:
- update cache management code
- rework trap handler with new define trap #.
- fix on check header warning.
* tag 'nios2-v4.1-rc1' of git://git.rocketboards.org/linux-socfpga-next:
nios2: rework cache
nios2: Add types.h header required for __u32 type
nios2: rework trap handler
nios2: remove end address checking for initda
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
eth: bf609 eth clock: add pclk clock for stmmac driver probe
blackfin: Wire up missing syscalls
arch: blackfin: kernel: kgdb: Remove unused function
dma: fix build error after update to v3.19
blackfin: io: define __raw_readx/writex with bfin_readx/writex
bf609: add resources for lcd nl8048
pm: sometimes wake up from suspend to RAM would fail
debug-mmrs: Eliminate all traces of the USB_PHY_TEST MMR
bf609: remove softswitch i2c configuration from adv7842 and adv7511 platform data
bf609: add platform data for soft switch devices on the video extenders
bf609: enable soft switch gpio driver by default
bf609: add gpio soft switch platform data for mcp23017 i2c devices
bf609: use new SND_BF6XX_PCM to choose audio pcm driver
bug[220] kgdb: change the smp cross core function entry
arch: blackfin: kernel: setup.c: Cleaning up missing null-terminate in conjunction with strncpy
blackfin: defconfigs: cleanup unused CONFIG_MTD_CHAR, add MTD_SPI_NOR for BF537-STAMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture updates from James Hogan:
"Just the one change for v4.1-rc1. A minor cleanup of copy_thread()"
* tag 'metag-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: copy_thread(): rename 'arg' argument to 'kthread_arg'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- perf fixes/improvements
- misc cleanups
* tag 'arc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: perf: don't add code for impossible case
ARC: perf: Rename DT binding to not confuse with power mgmt
ARC: perf: add user space attribution in callchains
ARC: perf: Add kernel callchain support
ARC: perf: support cache hit/miss ratio
ARC: perf: Add some comments/debug stuff
ARC: perf: make @arc_pmu static global
ARC: mem init spring cleaning - No functional changes
ARC: Fix RTT boot printing
ARC: fold __builtin_constant_p() into test_bit()
ARC: rename unhandled exception handler
ARC: cosmetic: Remove unused ECR bitfield masks
ARC: Fix WRITE_BCR
ARC: [nsimosci] Update defconfig
arc: copy_thread(): rename 'arg' argument to 'kthread_arg'
|
|
Commit cae2a173fe94 ("x86: clean up/fix 'copy_in_user()' tail zeroing")
fixed the failure case tail zeroing of one special case of the x86-64
generic user-copy routine, namely when used for the user-to-user case
("copy_in_user()").
But in the process it broke an even more unusual case: using the user
copy routine for kernel-to-kernel copying.
Now, normally kernel-kernel copies are obviously done using memcpy(),
but we have a couple of special cases when we use the user-copy
functions. One is when we pass a kernel buffer to a regular user-buffer
routine, using set_fs(KERNEL_DS). That's a "normal" case, and continued
to work fine, because it never takes any faults (with the possible
exception of a silent and successful vmalloc fault).
But Jan Beulich pointed out another, very unusual, special case: when we
use the user-copy routines not because it's a path that expects a user
pointer, but for a couple of ftrace/kgdb cases that want to do a kernel
copy, but do so using "unsafe" buffers, and use the user-copy routine to
gracefully handle faults. IOW, for probe_kernel_write().
And that broke for the case of a faulting kernel destination, because we
saw the kernel destination and wanted to try to clear the tail of the
buffer. Which doesn't work, since that's what faults.
This only triggers for things like kgdb and ftrace users (eg trying
setting a breakpoint on read-only memory), but it's definitely a bug.
The fix is to not compare against the kernel address start (TASK_SIZE),
but instead use the same limits "access_ok()" uses.
Reported-and-tested-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch e68410ebf626 ("crypto: x86/sha512_ssse3 - move SHA-384/512
SSSE3 implementation to base layer") changed the prototypes of the
core asm SHA-512 implementations so that they are compatible with
the prototype used by the base layer.
However, in one instance, the register that was used for passing the
input buffer was reused as a scratch register later on in the code,
and since the input buffer param changed places with the digest param
-which needs to be written back before the function returns- this
resulted in the scratch register to be dereferenced in a memory write
operation, causing a GPF.
Fix this by changing the scratch register to use the same register as
the input buffer param again.
Fixes: e68410ebf626 ("crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer")
Reported-By: Bobby Powers <bobbypowers@gmail.com>
Tested-By: Bobby Powers <bobbypowers@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
- flush dcache before flush instruction cache
- remork update_mmu_cache and flush_dcache_page
- add shmparam.h
Signed-off-by: Ley Foon Tan <lftan@altera.com>
|
|
Reported by the header checker (CONFIG_HEADERS_CHECK=y):
CHECK usr/include/asm/ (31 files)
./usr/include/asm/ptrace.h:77: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ley Foon Tan <lftan@altera.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
The related syscalls are below which may cause samples/kdbus building
break in next-20150401 tree, the related information and error:
CALL scripts/checksyscalls.sh
<stdin>:1223:2: warning: #warning syscall kcmp not implemented [-Wcpp]
<stdin>:1226:2: warning: #warning syscall finit_module not implemented [-Wcpp]
<stdin>:1229:2: warning: #warning syscall sched_setattr not implemented [-Wcpp]
<stdin>:1232:2: warning: #warning syscall sched_getattr not implemented [-Wcpp]
<stdin>:1235:2: warning: #warning syscall renameat2 not implemented [-Wcpp]
<stdin>:1238:2: warning: #warning syscall seccomp not implemented [-Wcpp]
<stdin>:1241:2: warning: #warning syscall getrandom not implemented [-Wcpp]
<stdin>:1244:2: warning: #warning syscall memfd_create not implemented [-Wcpp]
<stdin>:1247:2: warning: #warning syscall bpf not implemented [-Wcpp]
<stdin>:1250:2: warning: #warning syscall execveat not implemented [-Wcpp]
[...]
HOSTCC samples/kdbus/kdbus-workers
samples/kdbus/kdbus-workers.c: In function ‘prime_new’:
samples/kdbus/kdbus-workers.c:930:18: error: ‘__NR_memfd_create’ undeclared (first use in this function)
p->fd = syscall(__NR_memfd_create, "prime-area", MFD_CLOEXEC);
^
samples/kdbus/kdbus-workers.c:930:18: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
|
|
|
|
Remove the function kgdb_post_primary_code() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Sometimes it fails to wake up from suspend to RAM, this is because
we would flush the data cache by assemble command FLUSHINV before
suspend to RAM, and there is a delay between this command execution
and cache flush completion. Add a 1uS delay to works around this.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
|
|
Interacting with the USB_PHY_TEST MMR through debugfs was causing wide-spread
chaos in the realm (kernel panic). Expunge all references to this demonic
register.
Signed-off-by: Andre Wolokita <Andre.Wolokita@analog.com>
|
|
data
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
There is a new bf6xx audio dma driver, so we don't reuse
bf5xx i2s pcm driver again.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
conjunction with strncpy
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
BF537-STAMP
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
This fix the below build error
arch/powerpc/mm/hash_utils_64.c: In function ‘flush_hash_hugepage’:
arch/powerpc/mm/hash_utils_64.c:1381:1: error: label at end of compound statement
tm_abort:
^
make[1]: *** [arch/powerpc/mm/hash_utils_64.o] Error 1
Reported-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
These functions are used in various drivers, including the latest
version of the 8250 driver. The latter causes the following build
failure.
drivers/tty/serial/8250/8250_core.c: In function 'mem32be_serial_out':
drivers/tty/serial/8250/8250_core.c:456:2: error:
implicit declaration of function 'iowrite32be'
drivers/tty/serial/8250/8250_core.c: In function 'mem32be_serial_in':
drivers/tty/serial/8250/8250_core.c:462:2: error:
implicit declaration of function 'ioread32be'
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: c627f2ceb692 ("serial: 8250: Add support for big-endian MMIO
accesses")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
|
