| Age | Commit message (Collapse) | Author |
|---|
|
The dts-installed variable is initialised using a wildcard path that
will be expanded relative to the build directory. Use the existing
variable dtstree to generate an absolute wildcard path that will work
when building in a separate directory.
Reported-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Gerhard Pircher <gerhard_pircher@gmx.net> [against 2.6.32]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Decoding machine checks is CPU specific and so machine_check_generic doesn't
do the right thing on 64bit chips. Luckily we never call into this code
because we call ppc_md.machine_check_exception instead if available.
Since we check cur_cpu_spec->machine_check before calling it, we may as
well remove machine_check_generic from 64bit archs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The spec suggests we should first check the extended log flag before checking
the length field.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The FWNMI code uses a global buffer without any locks to read the RTAS error
information. If two CPUs take a machine check at once then we will corrupt
this buffer.
Since most FWNMI rtas messages are not of the extended type, we can create a
64bit percpu buffer and use it where possible. If we do receive an extended
RTAS log then we fall back to the old behaviour of using the global buffer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Rework pseries machine check handler:
- If MSR_RI isn't set, we cannot recover even if the machine check was fully
recovered
- Rename nonfatal to recovered
- Handle RTAS_DISP_LIMITED_RECOVERY
- Use BUS_MCEERR_AR instead of BUS_ADRERR
- Don't check all the RTAS error log fields when receiving a synchronous
machine check. Recent versions of the pseries firmware do not fill them
in during a machine check and instead send a follow up error log with
the detailed information. If we see a synchronous machine check, and we
came from userspace then kill the task.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If a machine check comes from userspace we send a SIGBUS to the task and
fail to printk anything.
If we are taking machine checks due to bad hardware we want to know about
it right away. Furthermore if we don't complain loudly then it will look
a lot like a bug in the userspace application, potentially causing a lot
of confusion.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We are calling debugger_fault_handler twice in machine_check_exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
machine check
Newer versions of the System p firwmare send a partial RTAS error log in the
machine check handler with a more detailed response appearing sometime later
via check event.
This means at machine check time we do not have enough information to
ascertain exactly what went on. Furthermore, I have found the RTAS error
logs in the machine check handler contain no useful information, so halting on
them makes little sense. If we want to halt it would make more sense to do
it following the error log received sometime later via check event.
In light of this, never halt the error log in the pseries machine
check handler.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We should never force MSR_RI on. If we take a machine check with MSR_RI off
then we have no chance of recovering safely.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We were printing 64 bits of DSISR in show_regs even though it is 32 bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We should disable ftrace during kexec, some of the tracers are very invasive
and we do not want them going off while doing the low level work of swapping
one kernel out for another. This mirrors what we do on x86.
Even though we cannot return from a kexec on powerpc (since we do not implement
CONFIG_KEXEC_JUMP), add the restore code in case we do one day.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Use the crash handler hooks to run the SPU stop code, just like we do for
ehea and cell RAS code.
While I'm here I noticed "CPUSs reliabally"
so fix the spelling MISTAKESs reliabally.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We check for a valid handler before calling ppc_md.machine_kexec_prepare
so we can just remove these empty handlers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There's no need to initialise ppc_md.machine_kexec and
ppc_md.machine_kexec_prepare to the default handlers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No one uses ppc_md.machine_crash_shutdown, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No one uses ppc_md.machine_kexec, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No one uses ppc_md.machine_kexec_cleanup, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Move all the kexec handlers together.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With cmwq, there's no reason to use a separate workqueue in
cpufreq_spudemand. Use system_wq instead. The work items are already
sync canceled on stop, so it's already guaranteed that no work is
running when spu_gov_exit() is entered.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Dave Jones <davej@redhat.com>
Cc: cpufreq@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Simplify read file operation for /proc/powerpc/rtas/* interface
by using simple_read_from_buffer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Simplify several write fileoperations for spufs by using
simple_write_to_buffer().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
32-bit variant of the previous patch for 64-bit:
<<
When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
With one level stack. But if we have irqsoff tracing enabled,
it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
goes two stack frames up. If this is from user space, then there may
not exist a second stack....
>>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
With one level stack. But if we have irqsoff tracing enabled,
it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
goes two stack frames up. If this is from user space, then there may
not exist a second stack.
Add a second stack when calling trace_hardirqs_on/off() otherwise
the following oops might occur:
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 PA Semi PWRficient
last sysfs file: /sys/block/sda/size
Modules linked in: ohci_hcd ehci_hcd usbcore
NIP: c0000000000e1c00 LR: c0000000000034d4 CTR: 000000011012c440
REGS: c00000003e2f3af0 TRAP: 0300 Not tainted (2.6.37-rc6+)
MSR: 9000000000001032 <ME,IR,DR> CR: 48044444 XER: 20000000
DAR: 00000001ffb9db50, DSISR: 0000000040000000
TASK = c00000003e1a00a0[2088] 'emacs' THREAD: c00000003e2f0000 CPU: 1
GPR00: 0000000000000001 c00000003e2f3d70 c00000000084e0d0 c0000000008816e8
GPR04: 000000001034c678 000000001032e8f9 0000000010336540 0000000040020000
GPR08: 0000000040020000 00000001ffb9db40 c00000003e2f3e30 0000000060000000
GPR12: 100000000000f032 c00000000fff0280 000000001032e8c9 0000000000000008
GPR16: 00000000105be9c0 00000000105be950 00000000105be9b0 00000000105be950
GPR20: 00000000ffb9dc50 00000000ffb9dbf0 00000000102f0000 00000000102f0000
GPR24: 00000000102e0000 00000000102f0000 0000000010336540 c0000000009ded38
GPR28: 00000000102e0000 c0000000000034d4 c0000000007ccb10 c00000003e2f3d70
NIP [c0000000000e1c00] .trace_hardirqs_off+0xb0/0x1d0
LR [c0000000000034d4] decrementer_common+0xd4/0x100
Call Trace:
[c00000003e2f3d70] [c00000003e2f3e30] 0xc00000003e2f3e30 (unreliable)
[c00000003e2f3e30] [c0000000000034d4] decrementer_common+0xd4/0x100
Instruction dump:
81690000 7f8b0000 419e0018 f84a0028 60000000 60000000 60000000 e95f0000
80030000 e92a0000 eb6301f8 2f800000 <eb890010> 41fe00dc a06d000a eb1e8050
---[ end trace 4ec7fd2be9240928 ]---
Reported-by: Joerg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When we create an alternative feature section, the else case must be the
same size or smaller than the body. This is because when we patch the
else case in we just overwrite the body, so there must be room.
Up to now we just did this by inspection, but it's quite easy to enforce
it in the assembler, so we should.
The only change is to add the ifgt block, but that effects the alignment
of the tabs and so the whole macro is modified.
Also add a test, but #if 0 it because we don't want to break the build.
Anyone who's modifying the feature macros should enable the test.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
In order to be able to suppress the use of SRAT tables that
32-bit Linux can't deal with (in one case known to lead to a
non-bootable system, unless disabling ACPI altogether), move the
"numa=" option handling to common code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
LKML-Reference: <4D36B581020000780002D0FF@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This reverts commit 86b1e8dd83cb ("x86: Make relocatable kernel work with
new binutils").
Markus Trippelsdorf reported a boot failure caused by this patch.
The real solution to the original patch will likely involve an
arch-generic solution to define an overlaid jiffies_64 and jiffies
variables.
Until that's done and tested on all architectures revert this commit to
solve the regression.
Reported-and-bisected-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "Lu, Hongjiu" <hongjiu.lu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4D36A759.60704@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear irqstack thread_info
x86: Make relocatable kernel work with new binutils
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
|
|
While most users of a physical Malta board are using the serial port
as the console, a lot of QEMU users would prefer to interact with a
graphical console. Enable the Cirrus FB support in the Malta default
configuration to make that possible. Note that the default console will
still be the serial port, users have to pass "console=tty0" to the
kernel to use the Cirrus FB.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2001/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add CONFIG_VIRTUALIZATION to the MIPS architecture and include the
the virtio code there. Used to enable the virtio drivers under QEMU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2002/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Just do what everyone else is doing by placing __read_mostly things in
the .data.read_mostly section.
mips_io_port_base can not be read-only (const) and writable
(__read_mostly) at the same time. One of them has to go, so I chose
to eliminate the __read_mostly. It will still get stuck in a portion
of memory that is not adjacent to things that are written, and thus
not be on a dirty cache line, for whatever that is worth.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add common platform_device and helper code to make the registration
of the built-in wireless MAC easier on the Atheros AR9130/AR9132
based boards. Also register the WMAC device on the AR81 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>,
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1952/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Several boards are using the built-in SPI controller of the
AR71XX/AR724X/AR913X SoCs. This patch adds common platform_device
and helper code to register it. Additionally, the patch registers
the SPI bus on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1956/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Almost all boards have one or more push buttons connected to GPIO lines.
This patch adds common code to register a platform_device for them.
The patch also adds support for the buttons on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1954/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All supported SoCs have a built-in hardware watchdog driver. This patch
registers a platform_device for that to make it usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1955/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Almost all boards have one or more LEDs connected to GPIO lines. This
patch adds common code to register a platform_device for them.
The patch also adds support for the LEDs on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1950/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1949/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch implements generic GPIO routines for the built-in
GPIO controllers of the Atheros AR71XX/AR724X/AR913X SoCs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch adds initial support for various Atheros SoCs based on the
MIPS 24Kc core. The following models are supported at the moment:
- AR7130
- AR7141
- AR7161
- AR9130
- AR9132
- AR7240
- AR7241
- AR7242
The current patch contains minimal support only, but the resulting
kernel can boot into user-space with using of an initramfs image on
various boards which are using these SoCs. Support for more built-in
devices and individual boards will be implemented in further patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1947/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In order not to be left behind, we add jump label support for MIPS.
Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On the off chance that uasm ever warns about overflow, there is no way
to know what the offending instruction is.
Change the printks to WARNs, so we can get a nice stack trace. It has
the added benefit of being much more noticeable than the short single
line warning message, so is less likely to be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1905/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Octeon can use scratch registers in the TLB handlers. Octeon II can
use LDX instructions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1904/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Needed by Octeon II optimized TLB handlers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Pachwork: https://patchwork.linux-mips.org/patch/1903/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If the CPU supports BBIT0 and BBIT1, use them in TLB handlers as they
are more efficient than an AND followed by an branch and then
restoring the clobbered register.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1873/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
these are already defined, but declaring them allow them to be used
outside of uasm.c.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Decide at runtime to use either Context or KScratch to hold the PGD
pointer.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
