Age | Commit message (Collapse) | Author |
|
commit afd0e5a876703accb95894f23317a13e2c49b523 upstream.
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR")
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60b89f1928af80b546b5c3fd8714a62f6f4b8844 upstream.
On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...
Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.
So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 017b5522d5e3 ("ARM: at91: Add new binding for sama5d3-ddramc")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e10889a3177340dcda7d29c6d8fbd97247b007b upstream.
This reverts commit cab43282682e ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d43 ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab43282682e ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d98ce0be541d4a3cfbb52cd75072c0339ebb500 upstream.
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117ba ("powerpc/kvm: make hypervisor state restore a function")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97ee351b50a49717543533cfb85b4bf9d88c9680 upstream.
Recent toolchains force the TOC to be 256 byte aligned. We need to
enforce this alignment in the zImage linker script, otherwise pointers
to our TOC variables (__toc_start) could be incorrect. If the actual
start of the TOC and __toc_start don't have the same value we crash
early in the zImage wrapper.
Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73580dac7618e4bcd21679f553cf3c97323fec46 upstream.
On those parisc machines which don't provide a software power off
function, the system currently kills the init process at the end of a
shutdown and unexpectedly restarts insteads of halting.
Fix it by adding a loop which will not return.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 316ec0624f951166daedbe446988ef92ae72b59f upstream.
The previously submitted patch did not resolve the random segmentation
faults observed on the phantom buildd system. There are still
unresolved problems with the Debian 4.8 and 4.9 kernels on C8000.
The attached patch removes the flush of the offset map pages and does a
whole data cache flush for large ranges. No other arch flushes the
offset map in these routines as far as I can tell.
I have not observed any random segmentation faults on rp3440 in two
weeks of testing with 4.10.0 and 4.10.1.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa2be9b3d6d2d699e9ca7cbfc00867c80e5da213 upstream.
Turning on crypto self-tests on a POWER8 shows:
alg: hash: Test 1 failed for crc32c-vpmsum
00000000: ff ff ff ff
Comparing the code with the Intel CRC32c implementation on which
ours is based shows that we are doing an init with 0, not ~0
as CRC32c requires.
This probably wasn't caught because btrfs does its own weird
open-coded initialisation.
Initialise our internal context to ~0 on init.
This makes the self-tests pass, and btrfs continues to work.
Fixes: 6dd7a82cc54e ("crypto: powerpc - Add POWER8 optimised crc32c")
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5dc855d44c2ad960a86f593c60461f1ae1566b6d upstream.
If one thread mmaps a perf event while another thread in the same mm
is in some context where active_mm != mm (which can happen in the
scheduler, for example), refresh_pce() would write the wrong value
to CR4.PCE. This broke some PAPI tests.
Reported-and-tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 7911d3f7af14 ("perf/x86: Only allow rdpmc if a perf_event is mapped")
Link: http://lkml.kernel.org/r/0c5b38a76ea50e405f9abe07a13dfaef87c173a1.1489694270.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be3606ff739d1c1be36389f8737c577ad87e1f57 upstream.
The kernel doesn't boot with both PROFILE_ANNOTATED_BRANCHES=y and KASAN=y
options selected. With branch profiling enabled we end up calling
ftrace_likely_update() before kasan_early_init(). ftrace_likely_update() is
built with KASAN instrumentation, so calling it before kasan has been
initialized leads to crash.
Use DISABLE_BRANCH_PROFILING define to make sure that we don't call
ftrace_likely_update() from early code before kasan_early_init().
Fixes: ef7f0d6a6ca8 ("x86_64: add KASan support")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: lkp@01.org
Cc: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/20170313163337.1704-1-aryabinin@virtuozzo.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44fee88cea43d3c2cac962e0439cb10a3cabff6d upstream.
Subhransu reported that convert_art_to_tsc() isn't working for him.
The ART to TSC relation is only set up for systems which use the refined
TSC calibration. Systems with known TSC frequency (available via CPUID 15)
are not using the refined calibration and therefor the ART to TSC relation
is never established.
Add the setup to the known frequency init path which skips ART
calibration. The init code needs to be duplicated as for systems which use
refined calibration the ART setup must be delayed until calibration has
been done.
The problem has been there since the ART support was introdduced, but only
detected now because Subhransu tested the first time on hardware which has
TSC frequency enumerated via CPUID 15.
Note for stable: The conditional has changed from TSC_RELIABLE to
TSC_KNOWN_FREQUENCY.
[ tglx: Rewrote changelog and identified the proper 'Fixes' commit ]
Fixes: f9677e0f8308 ("x86/tsc: Always Running Timer (ART) correlated clocksource")
Reported-by: "Prusty, Subhransu S" <subhransu.s.prusty@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: christopher.s.hall@intel.com
Cc: kevin.b.stanton@intel.com
Cc: john.stultz@linaro.org
Cc: akataria@vmware.com
Link: http://lkml.kernel.org/r/20170313145712.GI3312@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90922a2d03d84de36bf8a9979d62580102f31a92 upstream.
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 68925176296a8b995e503349200e256674bfe5ac upstream.
When invalidating guest TLBs, special care must be taken to
actually shoot the guest TLBs and not the host ones if we're
running on a VHE system. This is controlled by the HCR_EL2.TGE
bit, which we forget to clear before invalidating TLBs.
Address the issue by introducing two wrappers (__tlb_switch_to_guest
and __tlb_switch_to_host) that take care of both the VTTBR_EL2
and HCR_EL2.TGE switching.
Reported-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a05ef161cdd22faccffe06f21fc8f1e249565385 ]
Currently the build breaks if CMA=n and SPAPR_TCE_IOMMU=y:
arch/powerpc/mm/mmu_context_iommu.c: In function ‘mm_iommu_get’:
arch/powerpc/mm/mmu_context_iommu.c:193:42: error: ‘MIGRATE_CMA’ undeclared (first use in this function)
if (get_pageblock_migratetype(page) == MIGRATE_CMA) {
^~~~~~~~~~~
Fix it by using the existing is_migrate_cma_page(), which evaulates to
false when CMA=n.
Fixes: 2e5bbb5461f1 ("KVM: PPC: Book3S HV: Migrate pinned pages out of CMA")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4b6fad7097f883335b6d9627c883cb7f276d94c9 ]
At the moment the userspace tool is expected to request pinning of
the entire guest RAM when VFIO IOMMU SPAPR v2 driver is present.
When the userspace process finishes, all the pinned pages need to
be put; this is done as a part of the userspace memory context (MM)
destruction which happens on the very last mmdrop().
This approach has a problem that a MM of the userspace process
may live longer than the userspace process itself as kernel threads
use userspace process MMs which was runnning on a CPU where
the kernel thread was scheduled to. If this happened, the MM remains
referenced until this exact kernel thread wakes up again
and releases the very last reference to the MM, on an idle system this
can take even hours.
This moves preregistered regions tracking from MM to VFIO; insteads of
using mm_iommu_table_group_mem_t::used, tce_container::prereg_list is
added so each container releases regions which it has pre-registered.
This changes the userspace interface to return EBUSY if a memory
region is already registered in a container. However it should not
have any practical effect as the only userspace tool available now
does register memory region once per container anyway.
As tce_iommu_register_pages/tce_iommu_unregister_pages are called
under container->lock, this does not need additional locking.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d7baee6901b34c4895eb78efdbf13a49079d7404 ]
This changes mm_iommu_xxx helpers to take mm_struct as a parameter
instead of getting it from @current which in some situations may
not have a valid reference to mm.
This changes helpers to receive @mm and moves all references to @current
to the caller, including checks for !current and !current->mm;
checks in mm_iommu_preregistered() are removed as there is no caller
yet.
This moves the mm_iommu_adjust_locked_vm() call to the caller as
it receives mm_iommu_table_group_mem_t but it needs mm.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 88f54a3581eb9deaa3bd1aade40aef266d782385 ]
We are going to get rid of @current references in mmu_context_boos3s64.c
and cache mm_struct in the VFIO container. Since mm_context_t does not
have reference counting, we will be using mm_struct which does have
the reference counter.
This changes mm_iommu_init/mm_iommu_cleanup to receive mm_struct rather
than mm_context_t (which is embedded into mm).
This should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 59107e2f48831daedc46973ce4988605ab066de3 ]
There is a feature in Hyper-V ('Debug-VM --InjectNonMaskableInterrupt')
which injects NMI to the guest. We may want to crash the guest and do kdump
on this NMI by enabling unknown_nmi_panic. To make kdump succeed we need to
allow the kdump kernel to re-establish VMBus connection so it will see
VMBus devices (storage, network,..).
To properly unload VMBus making it possible to start over during kdump we
need to do the following:
- Send an 'unload' message to the hypervisor. This can be done on any CPU
so we do this the crashing CPU.
- Receive the 'unload finished' reply message. WS2012R2 delivers this
message to the CPU which was used to establish VMBus connection during
module load and this CPU may differ from the CPU sending 'unload'.
Receiving a VMBus message means the following:
- There is a per-CPU slot in memory for one message. This slot can in
theory be accessed by any CPU.
- We get an interrupt on the CPU when a message was placed into the slot.
- When we read the message we need to clear the slot and signal the fact
to the hypervisor. In case there are more messages to this CPU pending
the hypervisor will deliver the next message. The signaling is done by
writing to an MSR so this can only be done on the appropriate CPU.
To avoid doing cross-CPU work on crash we have vmbus_wait_for_unload()
function which checks message slots for all CPUs in a loop waiting for the
'unload finished' messages. However, there is an issue which arises when
these conditions are met:
- We're crashing on a CPU which is different from the one which was used
to initially contact the hypervisor.
- The CPU which was used for the initial contact is blocked with interrupts
disabled and there is a message pending in the message slot.
In this case we won't be able to read the 'unload finished' message on the
crashing CPU. This is reproducible when we receive unknown NMIs on all CPUs
simultaneously: the first CPU entering panic() will proceed to crash and
all other CPUs will stop themselves with interrupts disabled.
The suggested solution is to handle unknown NMIs for Hyper-V guests on the
first CPU which gets them only. This will allow us to rely on VMBus
interrupt handler being able to receive the 'unload finish' message in
case it is delivered to a different CPU.
The issue is not reproducible on WS2016 as Debug-VM delivers NMI to the
boot CPU only, WS2012R2 and earlier Hyper-V versions are affected.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: devel@linuxdriverproject.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Link: http://lkml.kernel.org/r/20161202100720.28121-1-vkuznets@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c74fd80f2f41d05f350bb478151021f88551afe8 ]
Revert the main part of commit:
af42b8d12f8a ("xen: fix MSI setup and teardown for PV on HVM guests")
That commit introduced reading the pci device's msi message data to see
if a pirq was previously configured for the device's msi/msix, and re-use
that pirq. At the time, that was the correct behavior. However, a
later change to Qemu caused it to call into the Xen hypervisor to unmap
all pirqs for a pci device, when the pci device disables its MSI/MSIX
vectors; specifically the Qemu commit:
c976437c7dba9c7444fb41df45468968aaa326ad
("qemu-xen: free all the pirqs for msi/msix when driver unload")
Once Qemu added this pirq unmapping, it was no longer correct for the
kernel to re-use the pirq number cached in the pci device msi message
data. All Qemu releases since 2.1.0 contain the patch that unmaps the
pirqs when the pci device disables its MSI/MSIX vectors.
This bug is causing failures to initialize multiple NVMe controllers
under Xen, because the NVMe driver sets up a single MSIX vector for
each controller (concurrently), and then after using that to talk to
the controller for some configuration data, it disables the single MSIX
vector and re-configures all the MSIX vectors it needs. So the MSIX
setup code tries to re-use the cached pirq from the first vector
for each controller, but the hypervisor has already given away that
pirq to another controller, and its initialization fails.
This is discussed in more detail at:
https://lists.xen.org/archives/html/xen-devel/2017-01/msg00447.html
Fixes: af42b8d12f8a ("xen: fix MSI setup and teardown for PV on HVM guests")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e4d88009f57057df7672fa69a32b5224af54d37 upstream.
While we can technically not run huge page guests right now, we can
setup a guest with huge pages. Trying to migrate it will trigger a
VM_BUG_ON and, if the kernel is not configured to panic on a BUG, it
will happily try to work on non-existing page table entries.
With this patch, we always return "dirty" if we encounter a large page
when migrating. This at least fixes the immediate problem until we
have proper handling for both kind of pages.
Fixes: 15f36eb ("KVM: s390: Add proper dirty bitmap support to S390 kvm.")
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a69e2fb70350a66f91175cd2625f1e8215c5b6e9 upstream.
The CPPR (Current Processor Priority Register) of a XICS interrupt
presentation controller contains a value N, such that only interrupts
with a priority "more favoured" than N will be received by the CPU,
where "more favoured" means "less than". So if the CPPR has the value 5
then only interrupts with a priority of 0-4 inclusive will be received.
In theory the CPPR can support a value of 0 to 255 inclusive.
In practice Linux only uses values of 0, 4, 5 and 0xff. Setting the CPPR
to 0 rejects all interrupts, setting it to 0xff allows all interrupts.
The values 4 and 5 are used to differentiate IPIs from external
interrupts. Setting the CPPR to 5 allows IPIs to be received but not
external interrupts.
The CPPR emulation in the OPAL XICS implementation only directly
supports priorities 0 and 0xff. All other priorities are considered
equivalent, and mapped to a single priority value internally. This means
when using icp-opal we can not allow IPIs but not externals.
This breaks Linux's use of priority values when a CPU is hot unplugged.
After migrating IRQs away from the CPU that is being offlined, we set
the priority to 5, meaning we still want the offline CPU to receive
IPIs. But the effect of the OPAL XICS emulation's use of a single
priority value is that all interrupts are rejected by the CPU. With the
CPU offline, and not receiving IPIs, we may not be able to wake it up to
bring it back online.
The first part of the fix is in icp_opal_set_cpu_priority(). CPPR values
of 0 to 4 inclusive will correctly cause all interrupts to be rejected,
so we pass those CPPR values through to OPAL. However if we are called
with a CPPR of 5 or greater, the caller is expecting to be able to allow
IPIs but not external interrupts. We know this doesn't work, so instead
of rejecting all interrupts we choose the opposite which is to allow all
interrupts. This is still not correct behaviour, but we know for the
only existing caller (xics_migrate_irqs_away()), that it is the better
option.
The other part of the fix is in xics_migrate_irqs_away(). Instead of
setting priority (CPPR) to 0, and then back to 5 before migrating IRQs,
we migrate the IRQs before setting the priority back to 5. This should
have no effect on an ICP backend with a working set_priority(), and on
icp-opal it means we will keep all interrupts blocked until after we've
finished doing the IRQ migration. Additionally we wait for 5ms after
doing the migration to make sure there are no IRQs in flight.
Fixes: d74361881f0d ("powerpc/xics: Add ICP OPAL backend")
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Tested-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Rewrote comments and change log, change delay to 5ms]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e148bd17f48bd17fca2f4f089ec879fa6e47e34c upstream.
emulate_step() uses a number of underlying kernel functions that were
initially not enabled for LE. This has been rectified since. So, fix
emulate_step() for LE for the corresponding instructions.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 886f9c69fc68f56ddea34d3de51ac1fc2ac8dfbc upstream.
All pointers to these functions were removed, so now they produce
warnings:
arch/mips/ralink/rt305x.c:92:13: error: 'rt305x_wdt_reset' defined but not used [-Werror=unused-function]
This removes the functions. If we need them again, the patch can be
reverted later.
Fixes: f576fb6a0700 ("MIPS: ralink: cleanup the soc specific pinmux data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Crispin <john@phrozen.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d92240d12a9c010e0094bbc9280aae4a6be9a2d5 upstream.
The functions were originally used for the module unload path,
but are not referenced any more and just cause warnings:
arch/mips/ralink/timer.c:104:13: error: 'rt_timer_disable' defined but not used [-Werror=unused-function]
arch/mips/ralink/timer.c:74:13: error: 'rt_timer_free' defined but not used [-Werror=unused-function]
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes: 62ee73d284e7 ("MIPS: ralink: Make timer explicitly non-modular")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c48568b3692f1a56cbf1935e4eea835e6b185b1 upstream.
Over the years the code has been changed various times leading to
argc/argv being defined in a different function to where we actually
use the variables. Clean this up by moving them to prom_init_cmdline().
Signed-off-by: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14902/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3f6046186ef45acfeebc5a59c9fb45cefc685e7 upstream.
Since linux-4.8, CPU_FREQ_STAT is a bool symbol, causing a warning in
kernelci.org:
arch/mips/configs/lemote2f_defconfig:42:warning: symbol value 'm' invalid for CPU_FREQ_STAT
This updates the defconfig to have the feature built-in.
Fixes: 1aefc75b2449 ("cpufreq: stats: Make the stats code non-modular")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15000/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23ca9b522383d3b9b7991d8586db30118992af4a upstream.
kernelci reports a failure of the ip28_defconfig build after upgrading its
gcc version:
arch/mips/sgi-ip22/Platform:29: *** gcc doesn't support needed option -mr10k-cache-barrier=store. Stop.
The problem apparently is that the -mr10k-cache-barrier=store option is now
rejected for CPUs other than r10k. Explicitly including the CPU in the
check fixes this and is safe because both options were introduced in
gcc-4.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea58fca1842a5dc410cae4167b01643db971a4e2 upstream.
Since linux-4.3, SCSI_DH is a bool symbol, causing a warning in
kernelci.org:
arch/mips/configs/ip27_defconfig:136:warning: symbol value 'm' invalid for SCSI_DH
This updates the defconfig to have the feature built-in.
Fixes: 086b91d052eb ("scsi_dh: integrate into the core SCSI code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15001/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b617649468390713db1515ea79fc772d2eb897a8 upstream.
One of the last remaining failures in kernelci.org is for a gcc bug:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: error: insn does not satisfy its constraints:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: internal compiler error: in extract_constrain_insn, at recog.c:2190
This is apparently broken in gcc-6 but fixed in gcc-7, and I cannot
reproduce the problem here. However, it is clear that ip27_defconfig
does not actually need this driver as the platform has only PCI-X but
not PCIe, and the qlge adapter in turn is PCIe-only.
The driver was originally enabled in 2010 along with lots of other
drivers.
Fixes: 59d302b342e5 ("MIPS: IP27: Make defconfig useful again.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15197/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1742ac265046f34223e06d5d283496f0291be259 upstream.
vdso.h includes <spaces.h> implicitly after defining CONFIG_32BITS.
This defeats the override in mach-ip27/spaces.h, leading to
a build error that shows up in kernelci.org:
In file included from arch/mips/include/asm/mach-ip27/spaces.h:29:0,
from arch/mips/include/asm/page.h:12,
from arch/mips/vdso/vdso.h:26,
from arch/mips/vdso/gettimeofday.c:11:
arch/mips/include/asm/mach-generic/spaces.h:28:0: error: "CAC_BASE" redefined [-Werror]
#define CAC_BASE _AC(0x80000000, UL)
An earlier patch tried to make the second definition conditional,
but that patch had the #ifdef in the wrong place, and would lead
to another warning:
arch/mips/include/asm/io.h: In function 'phys_to_virt':
arch/mips/include/asm/io.h:138:9: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
For all I can tell, there is no other reason than vdso32 to ever
include this file with CONFIG_32BITS set, and the vdso itself should
never refer to the base addresses as it is running in user space,
so adding an #ifdef here is safe.
Link: https://patchwork.kernel.org/patch/9418187/
Fixes: 3ffc17d8768b ("MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ddc16ad8e0bc7742fc96d5aaabc5b8698512cd1 upstream.
In linux-4.10-rc, NF_CT_PROTO_UDPLITE and NF_CT_PROTO_DCCP are bool
symbols instead of tristate, and kernelci.org reports a bunch of
warnings for this, like:
arch/mips/configs/malta_kvm_guest_defconfig:63:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/mips/configs/malta_defconfig:62:warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
arch/mips/configs/malta_defconfig:63:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/mips/configs/ip22_defconfig:70:warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
arch/mips/configs/ip22_defconfig:71:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
This changes all the MIPS defconfigs with these symbols to have them
built-in.
Fixes: 9b91c96c5d1f ("netfilter: conntrack: built-in support for UDPlite")
Fixes: c51d39010a1b ("netfilter: conntrack: built-in support for DCCP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c4ea6e28dbf15ab93632c5c189f3948366b8885 upstream.
Fengguang reported random corruptions from various locations on x86-32
after commits d2852a224050 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79df6a ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.
After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.
There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush. For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.
It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e630a0 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.
Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf95992b
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.
Fixes: c109bf95992b ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef947b2529f918d9606533eb9c32b187ed6a5ede upstream.
gup_pte_range() fails to check pte_allows_gup() before translating a DAX
pte entry, pte_devmap(), to a page. This allows writes to read-only
mappings, and bypasses the DAX cacheline dirty tracking due to missed
'mkwrite' faults. The gup_huge_pmd() path and the gup_huge_pud() path
correctly check pte_allows_gup() before checking for _devmap() entries.
Fixes: 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings")
Link: http://lkml.kernel.org/r/148804251312.36605.12665024794196605053.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Xiong Zhou <xzhou@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ab18701c66552944188dbcd0ce0012729baab84 upstream.
FDT tag parsing is not related to whether BLK_DEV_INITRD is configured
or not, move it out of the corresponding #ifdef/#endif block.
This fixes passing external FDT to the kernel configured w/o
BLK_DEV_INITRD support.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4920e3cf77347d7d7373552d4839e8d832321313 upstream.
The current implementation of setup_randomness uses the stack address
and therefore the pointer to the SYSIB 3.2.2 block as input data
address. Furthermore the length of the input data is the number of
virtual-machine description blocks which is typically one.
This means that typically a single zero byte is fed to
add_device_randomness.
Fix both of these and use the address of the first virtual machine
description block as input data address and also use the correct
length.
Fixes: bcfcbb6bae64 ("s390: add system information as device randomness")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da8fd820f389a0e29080b14c61bf5cf1d8ef5ca1 upstream.
Commit bcfcbb6bae64 ("s390: add system information as device
randomness") intended to add some virtual machine specific information
to the randomness pool.
Unfortunately it uses the page allocator before it is ready to use. In
result the page allocator always returns NULL and the setup_randomness
function never adds anything to the randomness pool.
To fix this use memblock_alloc and memblock_free instead.
Fixes: bcfcbb6bae64 ("s390: add system information as device randomness")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb94a687d96c570d46332a4a890f1dcb7310e643 upstream.
Return a sensible value if TASK_SIZE if called from a kernel thread.
This gets us around an issue with copy_mount_options that does a magic
size calculation "TASK_SIZE - (unsigned long)data" while in a kernel
thread and data pointing to kernel space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4a81d8eebdc1d209d034f62a082a5131e4242b5 upstream.
In binutils/libbfd (bfd/elf.c) it is enforced that all s390 specific ELF
notes like e.g. NT_S390_PREFIX or NT_S390_CTRS have "LINUX" specified
as note name. Otherwise the notes are ignored.
For /proc/vmcore we currently use "CORE" for these notes.
Up to now this has not been a real problem because the dump analysis tool
"crash" does not check the note name. But it will break all programs that
use libbfd for processing ELF notes.
So fix this and use "LINUX" for all s390 specific notes to comply with
libbfd.
Reported-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96794e4ed4d758272c486e1529e431efb7045265 upstream.
Guest segment selector is 16 bit field and guest segment base is natural
width field. Fix two incorrect invocations accordingly.
Without this patch, build fails when aggressive inlining is used with ICC.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1e8a9624f7ba8ead4f056ff558ed070e86fa747 upstream.
User controlled KVM guests do not support the dirty log, as they have
no single gmap that we can check for changes.
As they have no single gmap, kvm->arch.gmap is NULL and all further
referencing to it for dirty checking will result in a NULL
dereference.
Let's return -EINVAL if a caller tries to sync dirty logs for a
UCONTROL guest.
Fixes: 15f36eb ("KVM: s390: Add proper dirty bitmap support to S390 kvm.")
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae2f5e5ed04a17c1aa1f0a3714c725e12c21d2a9 upstream.
Fix the following build error with binutils 2.25.
CC arch/mips/mm/sc-ip22.o
{standard input}: Assembler messages:
{standard input}:132: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:159: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:200: Error: number (0x9000000080000000) larger than 32 bits
scripts/Makefile.build:293: recipe for target 'arch/mips/mm/sc-ip22.o' failed
make[1]: *** [arch/mips/mm/sc-ip22.o] Error 1
MIPS has used .set mips3 to temporarily switch the assembler to 64 bit
mode in 64 bit kernels virtually forever. Binutils 2.25 broke this
behavious partially by happily accepting 64 bit instructions in .set mips3
mode but puking on 64 bit constants when generating 32 bit ELF. Binutils
2.26 restored the old behaviour again.
Fix build with binutils 2.25 by open coding the offending
dli $1, 0x9000000080000000
as
li $1, 0x9000
dsll $1, $1, 48
which is ugly be the only thing that will build on all binutils vintages.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9f1c8db1c37253805eaa32265e1e1af3ae7d0a4 upstream.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fda2d27db6eae5c2468f9e4657539b72bbc238bb upstream.
We will set LPCR with correct value for radix during int. This make sure we
start with a sanitized value of LPCR. In case of kexec, cpus can have LPCR
value based on the previous translation mode we were running.
Fixes: fe036a0605d60 ("powerpc/64/kexec: Fix MMU cleanup on radix")
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5ecdad4847897007399d7a14c9109b65ce4c9b7 upstream.
Without this we will always find the feature disabled.
Fixes: 984d7a1ec6 ("powerpc/mm: Fixup kernel read only mapping")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c21a493a2b44650707d06741601894329486f2ad upstream.
Currently xmon data-breakpoint feature is broken.
Whenever there is a watchpoint match occurs, hw_breakpoint_handler will
be called by do_break via notifier chains mechanism. If watchpoint is
registered by xmon, hw_breakpoint_handler won't find any associated
perf_event and returns immediately with NOTIFY_STOP. Similarly, do_break
also returns without notifying to xmon.
Solve this by returning NOTIFY_DONE when hw_breakpoint_handler does not
find any perf_event associated with matched watchpoint, rather than
NOTIFY_STOP, which tells the core code to continue calling the other
breakpoint handlers including the xmon one.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d0928f18bf890d2853281f59aba0dd5a46b34f9 upstream.
Since it was introduced in commit da8d02d19ffdd201 ("arm64/capabilities:
Make use of system wide safe value"), __raw_read_system_reg() has
erroneously mapped some sysreg IDs to other registers.
For the fields in ID_ISAR5_EL1, our local feature detection will be
erroneous. We may spuriously detect that a feature is uniformly
supported, or may fail to detect when it actually is, meaning some
compat hwcaps may be erroneous (or not enforced upon hotplug).
This patch corrects the erroneous entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: da8d02d19ffdd201 ("arm64/capabilities: Make use of system wide safe value")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adbe7e26f4257f72817495b9bce114284060b0d7 upstream.
When bypassing SWIOTLB on small-memory systems, we need to avoid calling
into swiotlb_dma_mapping_error() in exactly the same way as we avoid
swiotlb_dma_supported(), because the former also relies on SWIOTLB state
being initialised.
Under the assumptions for which we skip SWIOTLB, dma_map_{single,page}()
will only ever return the DMA-offset-adjusted physical address of the
page passed in, thus we can report success unconditionally.
Fixes: b67a8b29df7e ("arm64: mm: only initialize swiotlb when necessary")
CC: Jisheng Zhang <jszhang@marvell.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f36ebaf21fdae99c091c67e8b6fab33969f2667 upstream.
When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.
But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.
The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.
Fixes: 2d58b733c876 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58ab9a088ddac4efe823471275859d64f735577e upstream.
Kirill reported a warning from UBSAN about undefined behavior when using
protection keys. He is running on hardware that actually has support for
it, which is not widely available.
The warning triggers because of very large shifts of integers when doing a
pkey_free() of a large, invalid value. This happens because we never check
that the pkey "fits" into the mm_pkey_allocation_map().
I do not believe there is any danger here of anything bad happening
other than some aliasing issues where somebody could do:
pkey_free(35);
and the kernel would effectively execute:
pkey_free(8);
While this might be confusing to an app that was doing something stupid, it
has to do something stupid and the effects are limited to the app shooting
itself in the foot.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Cc: kirill.shutemov@linux.intel.com
Link: http://lkml.kernel.org/r/20170223222603.A022ED65@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78162d48466d23c45a784034630c5928af631e3d upstream.
Enable DMA on uart1 to get a more reliable console.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|