| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RAS update from Ingo Molnar:
"The biggest change in this cycle is better support for UCNA
(UnCorrected No Action) events:
"Handle all uncorrected error reports in the same way (soft
offline the page). We used to only do that for SRAO
(software recoverable action optional) machine checks, but
it makes sense to also do it for UCNA (UnCorrected No
Action) logs found by CMCI or polling."
plus various x86 MCE handling updates and fixes"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Spell "panicked" correctly
x86, mce: Support memory error recovery for both UCNA and Deferred error in machine_check_poll
x86, mce, severity: Extend the the mce_severity mechanism to handle UCNA/DEFERRED error
x86, MCE, AMD: Assign interrupt handler only when bank supports it
x86, MCE, AMD: Drop software-defined bank in error thresholding
x86, MCE, AMD: Move invariant code out from loop body
x86, MCE, AMD: Correct thresholding error logging
x86, MCE, AMD: Use macros to compute bank MSRs
RAS, HWPOISON: Fix wrong error recovery status
GHES: Make ghes_estatus_caches static
APEI, GHES: Cleanup unnecessary function for lockless list
|
|
* pm-runtime: (25 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
PM / Kconfig: Do not select PM directly from Kconfig files
PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
...
|
|
* pm-cpuidle:
cpuidle: add MAINTAINERS entry for ARM Exynos cpuidle driver
drivers: cpuidle: Remove cpuidle-arm64 duplicate error messages
drivers: cpuidle: Add idle-state-name description to ARM idle states
drivers: cpuidle: Add status property to ARM idle states
cpuidle: Invert CPUIDLE_FLAG_TIME_VALID logic
|
|
* acpi-video:
ACPI / video: Run _BCL before deciding registering backlight
* acpi-pmic:
ACPI / PMIC: AXP288: support virtual GPIO in ACPI table
ACPI / PMIC: support PMIC operation region for XPower AXP288
ACPI / PMIC: support PMIC operation region for CrystalCove
iio/axp288_adc: remove THIS_MODULE owner
mfd/axp20x: avoid irq numbering collision
iio: adc: Add module device table for autoloading
iio: adc: Add support for axp288 adc
mfd: axp20x: Extend axp20x to support axp288 pmic
|
|
|
|
* acpi-scan:
ACPI: Add _DEP support to fix battery issue on Asus T100TA
* acpi-pm:
ACPI / sleep: Drain outstanding events after disabling multiple GPEs
ACPI / PM: Fixed a typo in a comment
* acpi-lpss:
dmaengine: dw: enable runtime PM
ACPI / LPSS: introduce a 'proxy' device to power on LPSS for DMA
ACPI / LPSS: allow to use specific PM domain during ->probe()
ACPI / LPSS: add all LPSS devices to the specific power domain
* acpi-processor:
ACPI / cpuidle: avoid assigning signed errno to acpi_status
ACPI / processor: remove unused variabled from acpi_processor_power structure
ACPI / processor: Update the comments in processor.h
|
|
* acpica:
ACPICA: Events: Always modify GPE registers under the GPE lock
ACPICA: Save current masks of enabled GPEs after enable register writes
ACPICA: Update version to 20141107.
ACPICA: Disassembler: Emit correct string for 0 stop bits.
ACPICA: Disassembler: Update for C-style expressions.
ACPICA: Disassembler: Add support for C-style operators and expressions.
ACPICA: acpiexec: Add option to specify an object initialization file.
ACPICA: iASL: Add support for to_PLD macro.
|
|
* acpi-config:
ACPI / Kconfig: Remove redundant depends on ACPI
* acpi-osl:
ACPI / OSL: Add IRQ handler flushing support in the OSL.
ACPI / osl: speedup grace period in acpi_os_map_cleanup
* acpi-utils:
ACPI: remove unnecessary sizeof(u8)
* acpi-tables:
ACPI / table: Always count matched and successfully parsed entries
ACPI / table: Add new function to get table entries
|
|
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the ACPI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
It is reported that there are pieces of code invoking acpi_ev_finish_gpe()
without holding acpi_gbl_gpe_lock. Since this function will modify GPE
register values, there could be races breaking the register modification
process.
This patch fixes this issue. Lv Zheng.
Reported-by: Joe Liu <joe.liu@apple.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After multiple GPEs have been disabled at the low level in one go,
like when acpi_disable_all_gpes() is called, we should always drain
all of the outstanding events from them, or interesting races become
possible.
For this reason, call acpi_os_wait_events_complete() after
acpi_enable_all_wakeup_gpes() and acpi_disable_all_gpes() in
acpi_freeze_prepare() and acpi_power_off_prepare(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
There is a race condition between acpi_hw_disable_all_gpes() or
acpi_enable_all_wakeup_gpes() and acpi_ev_asynch_enable_gpe() such
that if the latter wins the race, it may mistakenly enable a GPE
disabled by the former. This may lead to premature system wakeups
during system suspend and potentially to more serious consequences.
The source of the problem is how acpi_hw_low_set_gpe() works when
passed ACPI_GPE_CONDITIONAL_ENABLE as the second argument. In that
case, the GPE will be enabled if the corresponding bit is set in the
enable_for_run mask of the GPE enable register containing that bit.
However, acpi_hw_disable_all_gpes() and acpi_enable_all_wakeup_gpes()
don't modify the enable_for_run masks of GPE registers when writing
to them. In consequence, if acpi_ev_asynch_enable_gpe(), which
eventually calls acpi_hw_low_set_gpe() with the second argument
equal to ACPI_GPE_CONDITIONAL_ENABLE, is executed in parallel with
one of these functions, it may reverse changes made by them.
To fix the problem, introduce a new enable_mask field in struct
acpi_gpe_register_info in which to store the current mask of
enabled GPEs and modify acpi_hw_low_set_gpe() to take this
mask into account instead of enable_for_run when its second
argument is equal to ACPI_GPE_CONDITIONAL_ENABLE. Also modify
the low-level routines called by acpi_hw_disable_all_gpes(),
acpi_enable_all_wakeup_gpes() and acpi_enable_all_runtime_gpes()
to update the enable_mask masks of GPE registers after all
(successful) writes to those registers.
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 0b8db271f159 ("ACPI / video: check _DOD list when creating
backlight devices") checks if the video device is in the bind devices
list to decide if we should create backlight device for it, that causes
problem for one Dell Latitude E6410, where none of the video output
devices are properly bound due to the way how we did the comparing
between its _ADR and the _DOD's values. Solve this problem by comparing
the lower 12 bits of both the device's _ADR and the _DOD's values instead
of relying on bind result.
Fixes: 0b8db271f159 ("ACPI / video: check _DOD list when creating backlight devices")
Reported-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Was stop_bits_none, corrected to stop_bits_zero.
David E. Box.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add extra set of parens for assignments within an expression.
This patch only affects compiler support which is not in the Linux kernel.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now emit ASL+ code which includes C-style operators.
Optionally, legacy text ASL operators can still be emitted.
This patch only affects compiler/disassembler support which is not in the
Linux kernel.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This option (-fi) allows the specification of a file that is used
to specify initialization values for individual namespace objects.
Each line in the file is in the format:
<ACPI pathname> <Integer Value>
This patch only affects acpiexec which is not in the Linux kernel.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This macro is intended to simplify the constuction of _PLD buffers.
NOTE: Prototype only, subject to change before this macro is
added to the ACPI specification. David E. Box.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
acpi_parse_entries() allows to traverse all available table entries (aka
subtables) by passing max_entries parameter equal to 0, but since its count
variable is only incremented if max_entries is not 0, the function always
returns 0 for max_entries equal to 0. It would be more useful if it returned
the number of entries matched instead, so make it increment count in that
case too.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The acpi_table_parse() function has a callback that
passes a pointer to a table_header. Add a new function
which takes this pointer and parses its entries. This
eliminates the need to re-traverse all the tables for
each call. e.g. as in acpi_table_parse_madt() which is
normally called after acpi_table_parse().
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The same virtual GPIO strategy is also used for the AXP288 PMIC in that
various control methods that are used to do power rail handling and
sensor reading/setting will touch GPIO fields defined under the PMIC
device. The GPIO fileds are only defined by the ACPI code while the
actual hardware doesn't really have a GPIO controller, but to make those
control method execution succeed, we have to install a GPIO handler for
the PMIC device handle. Since we do not need the virtual GPIO strategy,
we can simply do nothing in that handler.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Baytrail-T-CR platform firmware has defined two customized operation
regions for PMIC chip Dollar Cove XPower - one is for power resource
handling and one is for thermal just like the CrystalCove one. This patch
adds support for them on top of the common PMIC opregion region code.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Baytrail-T platform firmware has defined two customized operation
regions for PMIC chip Crystal Cove - one is for power resource handling
and one is for thermal: sensor temperature reporting, trip point setting,
etc. This patch adds support for them on top of the existing Crystal Cove
PMIC driver.
The reason to split code into a separate file intel_pmic.c is that there
are more PMIC drivers with ACPI operation region support coming and we can
re-use those code. The intel_pmic_opregion_data structure is created also
for this purpose: when we need to support a new PMIC's operation region,
we just need to fill those callbacks and the two register mapping tables.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It's incorrect to assign a signed value to an unsigned acpi_status
variable. This patch fixes it by using a signed integer to return
error values.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI 5.0 introduces _DEP (Operation Region Dependencies) to designate
device objects that OSPM should assign a higher priority in start
ordering due to future operation region accesses.
On Asus T100TA, ACPI battery info are read from a I2C slave device via
I2C operation region. Before I2C operation region handler is installed,
battery _STA always returns 0. There is a _DEP method of designating
start order under battery device node.
This patch is to implement _DEP feature to fix battery issue on the
Asus T100TA. Introducing acpi_dep_list and adding dep_unmet count
in struct acpi_device. During ACPI namespace scan, create struct
acpi_dep_data for a valid pair of master (device pointed to by _DEP)/
slave(device with _DEP), record master's and slave's ACPI handle in
it and put it into acpi_dep_list. The dep_unmet count will increase
by one if there is a device under its _DEP. Driver's probe() should
return EPROBE_DEFER when find dep_unmet is larger than 0. When I2C
operation region handler is installed, remove all struct acpi_dep_data
on the acpi_dep_list whose master is pointed to I2C host controller
and decrease slave's dep_unmet. When dep_unmet decreases to 0, all
_DEP conditions are met and then do acpi_bus_attach() for the device
in order to resolve battery _STA issue on the Asus T100TA.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=69011
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Tested-by: Adam Williamson <adamw@happyassassin.net>
Tested-by: Michael Shigorin <shigorin@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Conflicts:
drivers/cpuidle/dt_idle_states.c
|
|
As reported by Dmitry, on some Chromebooks there are devices with
corresponding ACPI objects and with unusual system wakeup
configuration. Namely, they technically are wakeup-capable, but the
wakeup is handled via a platform-specific out-of-band mechanism and
the ACPI PM layer has no information on the wakeup capability. As
a result, device_may_wakeup(dev) called from acpi_dev_suspend_late()
returns 'true' for those devices, but the wakeup.flags.valid flag is
unset for the corresponding ACPI device objects, so acpi_device_wakeup()
reproducibly fails for them causing acpi_dev_suspend_late() to return
an error code. The entire system suspend is then aborted and the
machines in question cannot suspend at all.
Address the problem by ignoring the device_may_wakeup(dev) return
value in acpi_dev_suspend_late() if the ACPI companion of the device
being handled has wakeup.flags.valid unset (in which case it is clear
that the wakeup is supposed to be handled by other means).
This fixes a regression introduced by commit a76e9bd89ae7 (i2c:
attach/detach I2C client device to the ACPI power domain) as the
affected systems could suspend and resume successfully before that
commit.
Fixes: a76e9bd89ae7 (i2c: attach/detach I2C client device to the ACPI power domain)
Reported-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
sizeof(u8) is always 1.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since config ACPI_REDUCED_HARDWARE_ONLY is already depended
on ACPI (inside if ACPI / endif), so depdens on ACPI is redundant,
remove it and fix the minor syntax problem also.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* acpi-blacklist:
ACPI / blacklist: blacklist Win8 OSI for Dell Vostro 3546
|
|
The only place where the time is invalid is when the ACPI_CSTATE_FFH entry
method is not set. Otherwise for all the drivers, the time can be correctly
measured.
Instead of duplicating the CPUIDLE_FLAG_TIME_VALID flag in all the drivers
for all the states, just invert the logic by replacing it by the flag
CPUIDLE_FLAG_TIME_INVALID, hence we can set this flag only for the acpi idle
driver, remove the former flag from all the drivers and invert the logic with
this flag in the different governor.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is possible that a GPE handler or a fixed event handler still accessed
after removing the handlers by invoking acpi_remove_gpe_handler() or
acpi_remove_fixed_event_handler(), this possibility can crash OPSM after a
module removal. In the Linux kernel, though all other GPE drivers are not
modules, since the IPMI_SI (ipmi_si_intf.c) can be compiled as a module, we
still need to consider a solution for this issue when the driver switches
to ACPI_GPE_RAW_HANDLER mode in order to invoke GPE APIs.
ACPICA expects acpi_os_wait_events_complete() to be invoked after GPE
disabling so that OSPM can ensure all running GPE handlers have exitted.
But currently acpi_os_wait_events_complete() can only flush _Lxx/_Exx
evaluation work queue and this philosophy cannot work for drivers that have
installed a dedicated GPE handler.
The only way to protect a callback is to perform some state holders
(reference count, state machine) before invoking the callback. Then this
issue can only be fixed by the following means:
1. Flush GPE in ACPICA before invoking the GPE handler. But currently,
there is no such implementation in acpi_ev_gpe_dispatch().
2. Flush GPE in ACPICA OSL before invoking the SCI handler. But currently,
there is no such implementation in acpi_irq().
3. Flush IRQ in OSPM IRQ layer before invoking the IRQ handler. In Linus
kernel, this can be done by synchronize_irq().
4. Flush scheduling in OSPM vector entry layer before invoking the vector.
In Linux, this can be done by synchronize_sched().
Since ACPICA expects the GPE handlers to be flushed by the ACPICA OSL or
the GPE drivers. If it is implemented by the GPE driver, we should see
synchronize_irq()/synchronize_sched() invoked in such drivers. If it is
implemented by the ACPICA OSL, ACPICA currently provides
acpi_os_wait_events_complete() hook to achieve this. After the following
commit:
Commit: 69c841b6dd8313c9a673246cc0e2535174272cab
Author: Lv Zheng <lv.zheng@intel.com>
Subject: ACPICA: Update use of acpi_os_wait_events_complete interface.
The OSL acpi_os_wait_events_complete() is invoked after a GPE handler is
removed from acpi_remove_gpe_handler() or a fixed event handler is removed
from acpi_remove_fixed_event_handler(). Thus it is possible to implement
GPE handler flushing using this ACPICA OSL now. So the solution 1 is
currently not taken into account.
By examining the IPMI_SI driver, we noticed that the IPMI_SI driver:
1. Uses free_irq() to flush non GPE based IRQ handlers, in free_irq(),
synchronize_irq() is invoked, and
2. Uses acpi_remove_gpe_handler() to flush GPE based IRQ handlers, for such
IRQ handlers, there is no synchronize_irq() invoked.
Since there isn't synchronize_sched() implemented for this driver, from the
driver's perspective, acpi_remove_gpe_handler() should have properly
flushed the GPE handlers for it. Since the driver doesn't invoke
synchronize_irq(), the solution 3 is not what the drivers expect.
This patch implements solution 2. But since given the fact that the GPE is
managed inside of ACPICA, and implementing the GPE flushing requires to
implement the whole GPE management code again in the OSL, instead of
flushing GPE, this patch flushes IRQ in acpi_os_wait_events_complete(). The
flushing could last longer than expected as though the target GPE/fixed
event that is removed can be fastly flushed, other GPEs/fix events can still
be issued during the flushing period.
This patch fixes this issue by invoking synchronize_hardirq() in
acpi_os_wait_events_complete(). The reason why we don't invoke
synchronize_irq() is: currently ACPICA is not threaded IRQ capable and the
only difference between synchronize_irq() and synchronize_hardirq() is
synchronize_irq() also flushes threaded IRQ handlers. Thus using
synchronize_hardirq() can help to reduce the overall synchronization time
for the current ACPICA implementation.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: linux-acpi@vger.kernel.org
Cc: devel@acpica.org
Cc: openipmi-developer@lists.sourceforge.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The LPSS DMA controller does not have _PS0 and _PS3 methods. Moreover it can be
powered off automatically whenever the last LPSS device goes down. In case of
no power any access to the DMA controller will hang the system. The behaviour
is reproduced on some HP laptops based on Intel Bay Trail [1] as well as on
Asus T100 transformer.
This patch introduces a so called 'proxy' device that has the knobs to handle a
power of the LPSS island. When the system needs to program the DMA controller
it calls to the ACPI LPSS power domain callbacks that wake or suspend the
'proxy' device.
[1] http://www.spinics.net/lists/dmaengine/msg01514.html
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The LPSS DMA controller would like to use the specific PM domain callbacks
during early stage, namely in ->probe(). This patch moves the specific PM
domain assignment early to be accessible during a whole life time of the device
in the system.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the LPSS devices are located in the different power domains depends
on LPSS_SAVE_CTX flag. We would like to use the specific power domain for all
LPSS devices.
The LPSS DMA controller has no knobs to control its power state. The specific
power domain implementation will handle this case. The patch does a preparation
for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI maintains cache of ioremap regions to speed up operations and
access to them from irq context where ioremap() calls aren't allowed.
This code abuses synchronize_rcu() on unmap path for synchronization
with fast-path in acpi_os_read/write_memory which uses this cache.
Since v3.10 CPUs are allowed to enter idle state even if they have RCU
callbacks queued, see commit c0f4dfd4f90f1667d234d21f15153ea09a2eaa66
("rcu: Make RCU_FAST_NO_HZ take advantage of numbered callbacks").
That change caused problems with nvidia proprietary driver which calls
acpi_os_map/unmap_generic_address several times during initialization.
Each unmap calls synchronize_rcu and adds significant delay. Totally
initialization is slowed for a couple of seconds and that is enough to
trigger timeout in hardware, gpu decides to "fell off the bus". Widely
spread workaround is reducing "rcu_idle_gp_delay" from 4 to 1 jiffy.
This patch replaces synchronize_rcu() with synchronize_rcu_expedited()
which is much faster.
Link: https://devtalk.nvidia.com/default/topic/567297/linux/linux-3-10-driver-crash/
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The size_prop argument of the recently added function
acpi_dev_get_property_reference() is not used by the only current
caller of that function and is very unlikely to be used at any time
going forward.
Namely, for a property whose value is a list of items each containing
a references to a device object possibly accompanied by some integers,
the number of items in the list can always be computed as the number
of elements of type ACPI_TYPE_LOCAL_REFERENCE in the property package.
Thus it should never be necessary to provide an additional "cells"
property with a value equal to the number of items in that list. It
also should never be necessary to provide a "cells" property specifying
how many integers are supposed to be following each reference.
For this reason, drop the size_prop argument from
acpi_dev_get_property_reference() and update its caller accordingly.
Link: http://marc.info/?l=linux-kernel&m=141511255610556&w=2
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add new generic routines are provided for retrieving properties from
device description objects in the platform firmware in case there are
no struct device objects for them (either those objects have not been
created yet or they do not exist at all).
The following functions are provided:
fwnode_property_present()
fwnode_property_read_u8()
fwnode_property_read_u16()
fwnode_property_read_u32()
fwnode_property_read_u64()
fwnode_property_read_string()
fwnode_property_read_u8_array()
fwnode_property_read_u16_array()
fwnode_property_read_u32_array()
fwnode_property_read_u64_array()
fwnode_property_read_string_array()
in analogy with the corresponding functions for struct device added
previously. For all of them, the first argument is a pointer to struct
fwnode_handle (new type) that allows a device description object
(depending on what platform firmware interface is in use) to be
obtained.
Add a new macro device_for_each_child_node() for iterating over the
children of the device description object associated with a given
device and a new function device_get_child_node_count() returning the
number of a given device's child nodes.
The interface covers both ACPI and Device Trees.
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We have lots of existing Device Tree enabled drivers and allocating
separate _HID for each is not feasible. Instead we allocate special _HID
"PRP0001" that means that the match should be done using Device Tree
compatible property using driver's .of_match_table instead if the driver
is missing .acpi_match_table.
If there is a need to distinguish from where the device is enumerated
(DT/ACPI) driver can check dev->of_node or ACPI_COMPATION(dev).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a uniform interface by which device drivers can request device
properties from the platform firmware by providing a property name
and the corresponding data type. The purpose of it is to help to
write portable code that won't depend on any particular platform
firmware interface.
The following general helper functions are added:
device_property_present()
device_property_read_u8()
device_property_read_u16()
device_property_read_u32()
device_property_read_u64()
device_property_read_string()
device_property_read_u8_array()
device_property_read_u16_array()
device_property_read_u32_array()
device_property_read_u64_array()
device_property_read_string_array()
The first one allows the caller to check if the given property is
present. The next 5 of them allow single-valued properties of
various types to be retrieved in a uniform way. The remaining 5 are
for reading properties with multiple values (arrays of either numbers
or strings).
The interface covers both ACPI and Device Trees.
This change set includes material from Mika Westerberg and Aaron Lu.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Device Tree is used in many embedded systems to describe the system
configuration to the OS. It supports attaching properties or name-value
pairs to the devices it describe. With these properties one can pass
additional information to the drivers that would not be available
otherwise.
ACPI is another configuration mechanism (among other things) typically
seen, but not limited to, x86 machines. ACPI allows passing arbitrary
data from methods but there has not been mechanism equivalent to Device
Tree until the introduction of _DSD in the recent publication of the
ACPI 5.1 specification.
In order to facilitate ACPI usage in systems where Device Tree is
typically used, it would be beneficial to standardize a way to retrieve
Device Tree style properties from ACPI devices, which is what we do in
this patch.
If a given device described in ACPI namespace wants to export properties it
must implement _DSD method (Device Specific Data, introduced with ACPI 5.1)
that returns the properties in a package of packages. For example:
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"name1", <VALUE1>},
Package () {"name2", <VALUE2>},
...
}
})
The UUID reserved for properties is daffd814-6eba-4d8c-8a91-bc9bbf4aa301
and is documented in the ACPI 5.1 companion document called "_DSD
Implementation Guide" [1], [2].
We add several helper functions that can be used to extract these
properties and convert them to different Linux data types.
The ultimate goal is that we only have one device property API that
retrieves the requested properties from Device Tree or from ACPI
transparent to the caller.
[1] http://www.uefi.org/sites/default/files/resources/_DSD-implementation-guide-toplevel.htm
[2] http://www.uefi.org/sites/default/files/resources/_DSD-device-properties-UUID.pdf
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* acpi-scan:
ACPI: Use ACPI companion to match only the first physical device
* acpi-ec:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
|
|
The wireless hotkey of Dell Vostro 3546 does not work with Win8 OSI. Due
to insufficient documentation for the driver implementation, blacklist
it as a workaround.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ASUS K53SM's ACPI table queries _OSI("Windows 2012") in the video
output device's _BCL and _BCM control method instead of the usual _INI
functions of the _SB or PCI host bridge PCI0 devices. This made our
video module thought this is a pre-Win8 system when deciding if we
should register a backlight interface for it and the end result is that
a non-working acpi_video interface is registered and user is unable to
control backlight from GUI. Solve this problem by evaluating _BCL control
method before doing the decision.
Note that for some Thinkpad systems, the _BCL is also required to be
evaluated for the hotkey event to be generated no matter if we will
register an ACPI video backlight interface for it or not. Since the
thinkpad_acpi module will do this anyway we didn't add such a thing in
the video module previously. But now with this change here, the
thinkpad_acpi module is no more necessary for those systems regarding
backlight functionality.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85051
Reported-and-tested-by: Ralf Jung <post+kernel@ralfj.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Samsung and Acer.
It is reported that Samsung laptops that need to poll events are broken by
the following commit:
Commit 3afcf2ece453e1a8c2c6de19cdf06da3772a1b08
Subject: ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
The behaviors of the 2 vendor firmwares are conflict:
1. Acer: OSPM shouldn't issue QR_EC unless SCI_EVT is set, firmware
automatically sets SCI_EVT as long as there is event queued up.
2. Samsung: OSPM should issue QR_EC whatever SCI_EVT is set, firmware
returns 0 when there is no event queued up.
This patch is a quick fix to distinguish the behaviors to make Acer
behavior only effective for Acer EC firmware so that the breakages on
Samsung EC firmware can be avoided.
Fixes: 3afcf2ece453 (ACPI / EC: Add support to disallow QR_EC to be issued ...)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
[ rjw : Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
