| Age | Commit message (Collapse) | Author |
|---|
|
In case the lower level device size changed, but some other internal
details of the resize did not work out, drbd_determine_dev_size() would
try to restore the previous settings, trusting
drbd_md_set_sector_offsets() to "do the right thing", but overlooked
that this internally may set the meta data base offset based on device size.
This could end up with incomplete on-disk meta data layout change, and
ultimately lead to data corruption (if the failure was not noticed or
ignored by the operator, and other things go wrong as well).
Just remember all meta data related offsets/sizes,
and on error restore them all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
During handshake communication, we also reconsider our device size,
using drbd_determine_dev_size(). Just in case we need to change the
offsets or layout of our on-disk metadata, we lock out application
and other meta data IO, and wait for the activity log to be "idle"
(no more referenced extents).
If this handshake happens just after a connection loss, with a fencing
policy of "resource-and-stonith", we have frozen IO.
If, additionally, the activity log was "starving" (too many incoming
random writes at that point in time), it won't become idle, ever,
because of the frozen IO, and this would be a lockup of the receiver
thread, and consquentially of DRBD.
Previous logic (re-)initialized with a special "empty" transaction
block, which required the activity log to fully drain first.
Instead, write out some standard activity log transactions.
Using lc_try_lock_for_transaction() instead of lc_try_lock() does not
care about pending activity log references, avoiding the potential
deadlock.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Avoid to prematurely resume application IO: don't set/clear a single
bit, but inc/dec an atomic counter.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
new_disk_conf could be leaked if the follow on checks fail,
so make sure to free it on error if it was not assigned yet.
Found with smatch.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
lsblk should be able to pick up stacking device driver relations
involving DRBD conveniently.
Even though upstream kernel since 2011 says
"DON'T USE THIS UNLESS YOU'RE ALREADY USING IT."
a new user has been added since (bcache),
which sets the precedences for us to use it as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We cannot possibly support SECDISCARD, even if all backend devices would
support it: if our peer is currently unreachable, some instance of the
data may obviously still be recoverable.
We did not set discard_granularity at all. We don't really care (yet),
we only pass them on, so for now, set our granularity to one sector.
blkdev_stack_limits() takes care of the rest.
If we decide we cannot support discards,
not only clear the (not user visible) QUEUE_FLAG_DISCARD,
but set both (user visible) discard_granularity and max_discard_sectors
to zero, to avoid confusion with e.g. lsblk -D.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In a multiple error scenario, we may end up with a "frozen" Primary,
that has no access to any data (no local disk, no replication link).
If we then resume-io, we try to generate a new data generation id,
which will fail if there is no longer a local disk.
Double check for available local data,
which prevents the NULL pointer deref.
If we are diskless, turn the resume-io in this situation
into the first stage of a "force down", by bumping the "effective" data
gen id, which will prevent later attach or connect to the former data
set without first being demoted (deconfigured).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The intention is to reduce CPU utilization. Recent measurements
unveiled that the current performance bottleneck is CPU utilization
on the receiving node. The asender thread became CPU limited.
One of the main points is to eliminate the idr_for_each_entry() loop
from the sending acks code path.
One exception in that is sending back ping_acks. These stay
in the ack-receiver thread. Otherwise the logic becomes too
complicated for no added value.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A D_FAILED disk transitions as quickly as possible to
D_DISKLESS. But in the "unresponsive local disk" case,
there remains a time window where a administrative detach command could
find the disk already failed, but some internal meta data IO against the
unresponsive local disk still pending.
In that case, drbd_md_get_buffer() will return NULL.
Don't unconditionally call drbd_md_put_buffer(), or it will cause
refcount imbalance, and prevent any further re-attach on this volume
(until it is deleted and re-created).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
"forever"
When detaching, we make sure no application IO is in-flight
by internally suspending IO, then trigger the state change,
wait for the result, and finally internally resume IO again.
Once we triggered the stat change to "Failed",
we expect it to change from Failed to Diskless.
(To avoid races, we actually wait for it to leave "Failed").
On an unresponsive local IO backend, this may not happen, ever.
Don't have a "hung" detach block IO "forever", but resume IO
before waiting for the state change to Diskless.
We may well be able to continue IO to and from a healthy peer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
GFP_NOWAIT has a value of 0. I.e. functionality not changed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The lc_destroy() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The status command originates the drbd9 code base. While for now we
keep the status information in /proc/drbd available, this commit
allows the user base to gracefully migrate their monitoring
infrastructure to the new status reporting interface.
In drbd9 no status information is exposed through /proc/drbd.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The events2 command originates from drbd-9 development. It features
more information but requires a incompatible change in output
format.
Therefore the previous events command continues to exist, the new
improved events2 command becomes available now.
This prepares the user-base for a later switch to the complete
drbd9 code base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Instead of using a rwlock for synchronizing state changes across
resources, take the request locks of all resources for global state
changes. Use resources_mutex to serialize global state changes.
This means that taking the request lock of a resource is now enough to
prevent changes of that resource. (Previously, a read lock on the
global state lock was needed as well.)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Also change the enum values to all-capital letters.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In drbd-8.4 there is always a single connection per resource,
and there is always exactly one peer_device for a device.
peer_device can not be NULL here.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Some drivers use it now, others just set the limits field manually.
But in preparation for splitting this into a hard and soft limit,
ensure that they all call the proper function for setting the hw
limit for discards.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Symptoms:
If DRBD was "cleanly shut down" (all in sync, both Secondary before
disconnect, identical data generation uuids), and then one side was
promoted *during* the next connection handshake, the role change
could confuse the handshake.
The Primary would get stuck in WFBitmapS, the Secondary would log
unexpected cstate (Connected) in receive_bitmap
and get stuck in WFBitmapT.
Fix:
The test in is_valid_soft_transition wrong. It works because
the not allowed actions (promote/attach) do not touch the
cstate. The previous condition failed to demand a cstate change
in one clause.
In order to avoid deadlocks give up the state_mutex while waiting
for the transient state to go away.
Conflicts:
drbd/drbd_state.c
drbd/drbd_state.h
drbd/drbd_wrappers.h
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Avoid generic netlink calls in other parts of the code base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
. Update comments
. drbd_set_{in,out_of}_sync(): Remove unused parameters
. Move common code into adm_del_resource()
. Redefine ERR_MINOR_EXISTS -> ERR_MINOR_OR_VOLUME_EXISTS
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Pull block driver changes from Jens Axboe:
"Nothing out of the ordinary here, this pull request contains:
- A big round of fixes for bcache from Kent Overstreet, Slava Pestov,
and Surbhi Palande. No new features, just a lot of fixes.
- The usual round of drbd updates from Andreas Gruenbacher, Lars
Ellenberg, and Philipp Reisner.
- virtio_blk was converted to blk-mq back in 3.13, but now Ming Lei
has taken it one step further and added support for actually using
more than one queue.
- Addition of an explicit SG_FLAG_Q_AT_HEAD for block/bsg, to
compliment the the default behavior of adding to the tail of the
queue. From Douglas Gilbert"
* 'for-3.17/drivers' of git://git.kernel.dk/linux-block: (86 commits)
bcache: Drop unneeded blk_sync_queue() calls
bcache: add mutex lock for bch_is_open
bcache: Correct printing of btree_gc_max_duration_ms
bcache: try to set b->parent properly
bcache: fix memory corruption in init error path
bcache: fix crash with incomplete cache set
bcache: Fix more early shutdown bugs
bcache: fix use-after-free in btree_gc_coalesce()
bcache: Fix an infinite loop in journal replay
bcache: fix crash in bcache_btree_node_alloc_fail tracepoint
bcache: bcache_write tracepoint was crashing
bcache: fix typo in bch_bkey_equal_header
bcache: Allocate bounce buffers with GFP_NOWAIT
bcache: Make sure to pass GFP_WAIT to mempool_alloc()
bcache: fix uninterruptible sleep in writeback thread
bcache: wait for buckets when allocating new btree root
bcache: fix crash on shutdown in passthrough mode
bcache: fix lockdep warnings on shutdown
bcache allocator: send discards with correct size
bcache: Fix to remove the rcu_sched stalls.
...
|
|
For diagnostic purposes, track intent, start time
and latest submit time of meta data IO.
Move separate members from struct drbd_device
into the embeded struct drbd_md_io.
s/md_io_(page|in_use)/md_io.\1/
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Cosmetic change only.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
The recent fix to put_ldev() (correct ordering of access to local_cnt
and state.disk; memory barrier in __drbd_set_state) guarantees
that the cleanup happens exactly once.
However it does not yet guarantee that the cleanup happens from worker
context, the last put_ldev() may still happen from atomic context,
which must not happen: blkdev_put() may sleep.
Fix this by scheduling the cleanup to the worker instead,
using a couple more bits in device->flags and a new helper,
drbd_device_post_work().
Generalized the "resync progress" work to cover these new work bits.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
This probably does not have any real life impact,
but we should first persist any potentially new UUID
and other meta data flags, as well as our new role,
before we allow/disallow write access.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
The conf_update mutex used to be held while clearing the
net_conf->discard_my_data flag inside drbd_set_role.
It was moved into drbd_adm_set_role with
drbd: allow parallel promote/demote actions
but then replaced at that location by the newly introduced adm_mutex with
drbd: Fix a potential deadlock in drbdsetup, introduce resource->adm_mutex
And I simply forgot to put it back in at the original location.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
If we re-write all meta data due to resize, we have open-coded write-out
of our meta data super block. Stop the md_sync_timer, it would just
trigger scary but in this case spurious "timer expired" messages.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Just trigger the occasional lazy bitmap write-out during resync
from the central wait_for_work() helper.
Previously, during resync, bitmap pages would be written out separately,
synchronously, one at a time, at least 8 times each (every 512 bytes
worth of bitmap cleared).
Now we trigger "merge friendly" bulk write out of all cleared pages
every two seconds during resync, and once the resync is finished.
Most pages will be written out only once.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Previously, once you disabled flushes as a means of enforcing
write-ordering, you'd need to detach/re-attach to enable them again.
Allow drbdsetup disk-options to re-enable previously disabled
write-ordering policy options at runtime.
While at it fix RCU in drbd_bump_write_ordering()
max_allowed_wo() uses rcu_dereference, therefore it must
be called within rcu_read_lock()/rcu_read_unlock()
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Reduce the number of calls to first_peer_device(). Instead, call
first_peer_device() just once to assign a local variable peer_device.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Some parts of the code assumed that get_ldev_if_state(device, D_ATTACHING)
is sufficient to access the ldev member of the device object. That was
wrong. ldev may not be there or might be freed at any time if the device
has a disk state of D_ATTACHING.
bm_rw()
Documented that drbd_bm_read() is only called from drbd_adm_attach.
drbd_bm_write() is only called when a reference is held, and it is
documented that a caller has to hold a reference before calling
drbd_bm_write()
drbd_bm_write_page()
Use get_ldev() instead of get_ldev_if_state(device, D_ATTACHING)
drbd_bmio_set_n_write()
No longer use get_ldev_if_state(device, D_ATTACHING). All callers
hold a reference to ldev now.
drbd_bmio_clear_n_write()
All callers where holding a reference of ldev anyways. Remove the
misleading get_ldev_if_state(device, D_ATTACHING)
drbd_reconsider_max_bio_size()
Removed the get_ldev_if_state(device, D_ATTACHING). All callers
now pass a struct drbd_backing_dev* when they have a proper
reference, or a NULL pointer.
Before this fix, the receiver could trigger a NULL pointer
deref when in drbd_reconsider_max_bio_size()
drbd_bump_write_ordering()
Used get_ldev_if_state(device, D_ATTACHING) with the wrong assumption.
Remove it, and allow the caller to pass in a struct drbd_backing_dev*
when the caller knows that accessing this bdev is safe.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Since linux kernel 3.13, kthread_run() internally uses
wait_for_completion_killable(). We sometimes may use kthread_run()
while we still have a signal pending, which we used to kick our threads
out of potentially blocking network functions, causing kthread_run() to
mistake that as a new fatal signal and fail.
Fix: flush_signals() before kthread_run().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A newly created device was never exposed before, i.e. has a
exposed_data_uuid of 0. Then it is valid to attach to any current_uuid
of a backing device (of course also to a newly created one (4))
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In case a connection transitions into C_TIMEOUT within the timer
function (request_timer_fn()) we need to make sure that the receiver
thread (potentially running on a different CPU) sees the updated
cstate later on.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
...instead directly assigning to q->limits.discard_zeroes_data
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We want to store in persistent meta data what the peer DRBD can handle,
which, due to spreading requests to multiple bios,
may be more than its backing device can handle.
Otherwise, if a disconnected Primary temporarily loses access to its local data
as well, we may accidentally shrink the max-bio setting, portentially causing
already assembled, but not yet processed, application bios to be spuriously
failed due to device limits.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Allow the user of REQ_DISCARD.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We plan to use genl_family->parallel_ops = true in the future,
but need to review all possible interactions first.
For now, only selectively drop genl_lock() in drbd_set_role(),
instead serializing on our own internal resource->conf_update mutex.
We now can be promoted/demoted on many resources in parallel,
which may significantly improve cluster failover times
when fencing is required.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Because all administrative requests via genetlink have been globally
serialized via genl_lock(), we used to have one static struct
drbd_config_context "admin context".
Move this on-stack to the respective callback functions.
This will allow us to selectively drop the genl_lock()
(or use genl_family->parallel_ops) in the future.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If a user forces the operation he takes the blame in case
the peer does not have enough space. No reason to dey this...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Actually we are clearing the susp_fen flag if we are not going
to call a fencing handler.
For setting the susp_fen flag needs to be edge-triggerd, and not
level triggered.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Right now every resource has exactly one connection. But we are preparing
for dynamic connections. I.e. in the future thre can be resources without
connections.
However smatch points this out as 'variable dereferenced before check',
which is correct.
This issue was introduced in
drbd: get_one_status(): Iterate over resource->devices instead of connection->peer_devices
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The new function can flush any work queue, not just the work queue of the data
socket of a connection.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
|
|
These functions actually operate on a peer device, or
need a peer device.
drbd_prepare_command(), drbd_send_command(), drbd_send_sync_param()
drbd_send_uuids(), drbd_gen_and_send_sync_uuid(), drbd_send_sizes()
drbd_send_state(), drbd_send_current_state(), and drbd_send_state_req()
drbd_send_sr_reply(), drbd_send_ack(), drbd_send_drequest(),
drbd_send_drequest_csum(), drbd_send_ov_request(), drbd_send_dblock()
drbd_send_block(), drbd_send_out_of_sync(), recv_dless_read()
drbd_drain_block(), receive_bitmap_plain(), recv_resync_read()
read_in_block(), read_for_csum(), drbd_alloc_pages(), drbd_alloc_peer_req()
need_peer_seq(), update_peer_seq(), wait_for_and_update_peer_seq()
drbd_sync_handshake(), drbd_asb_recover_{0,1,2}p(), drbd_connected()
drbd_disconnected(), decode_bitmap_c() and recv_bm_rle_bits()
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
|
|
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
|
