| Age | Commit message (Collapse) | Author |
|---|
|
commit d1bd4a792d3961a04e6154118816b00167aad91a upstream.
If a TPM2 loses power without a TPM2_Shutdown command being issued (a
"disorderly reboot"), it may lose some state that has yet to be
persisted to NVRam, and will increment the DA counter. After the DA
counter gets sufficiently large, the TPM will lock the user out.
NOTE: This only changes behavior on TPM2 devices. Since TPM1 uses sysfs,
and sysfs relies on implicit locking on chip->ops, it is not safe to
allow this code to run in TPM1, or to add sysfs support to TPM2, until
that locking is made explicit.
Signed-off-by: Josh Zimmerman <joshz@google.com>
Fixes: 74d6b3ceaa17 ("tpm: fix suspend/resume paths for TPM 2.0")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13b47cfcfc60495cde216eef4c01040d76174cbe upstream.
While cleaning up sysfs callback that prints EK we discovered a kernel
memory leak. This commit fixes the issue by zeroing the buffer used for
TPM command/response.
The leak happen when we use either tpm_vtpm_proxy, tpm_ibmvtpm or
xen-tpmfront.
Fixes: 0883743825e3 ("TPM: sysfs functions consolidation")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31574d321c70f6d3b40fe98f9b2eafd9a903fef9 upstream.
The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma. This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.
The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data. Attempting to get data before
the probe() caused the problem.
This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.
fixes: 9e0d39d8a6a0 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8569defde8057258835c51ce01a33de82e14b148 upstream.
Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.
Fixes: 30fc8d138e912 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0afb7118ae021e80ecf70f5a3336e0935505518a upstream.
Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.
This patch calls usleep_range() only if retry is to be done.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a233a0289cf9a96ef9b42c730a7621ccbf9a6f98 upstream.
Commit 500462a9de65 "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers. Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration. The only exception noted to this were
networking timers with a small expiry time.
Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay. The
non-cascading wheel delay is based on CONFIG_HZ. For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.
Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.
* HZ 1000 steps
* Level Offset Granularity Range
* 0 0 1 ms 0 ms - 63 ms
* 1 64 8 ms 64 ms - 511 ms
* 2 128 64 ms 512 ms - 4095 ms (512ms - ~4s)
* HZ 250
* Level Offset Granularity Range
* 0 0 4 ms 0 ms - 255 ms
* 1 64 32 ms 256 ms - 2047 ms (256ms - ~2s)
* 2 128 256 ms 2048 ms - 16383 ms (~2s - ~16s)
Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9de65.
linux-4.7 | msleep() usleep_range()
1000 hz: 0m44.628s | 1m34.497s 29.243s
250 hz: 1m28.510s | 4m49.269s 32.386s
linux-4.7 | min-max (msleep) min-max (usleep_range)
1000 hz: 0:017 - 2:760s | 0:015 - 3:967s 0:014 - 0:418s
250 hz: 0:028 - 1:954s | 0:040 - 4:096s 0:016 - 0:816s
This patch replaces the msleep() with usleep_range() calls in the
i2c nuvoton driver with a consistent max range value.
Signed-of-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5cc0101d1f88500f8901d01b035af743215d4c3a upstream.
Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.
As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 591e48c26ced7c455751eef27fb5963e902c2137 upstream.
Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.
v2: Moved scope of spi_message to the top as requested by Jarkko
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e110cc69dc2ad679d6d478df636b99b14e6fbbc9 upstream.
Wait states are signaled in the last byte received from the TPM in
response to the header, not the first byte. Check rx_buf[3] instead of
rx_buf[0].
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 975094ddc369a32f27210248bdd9bbd153061b00 upstream.
Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f848f2143ae42dc0918400039257a893835254d1 upstream.
The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.
This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)
v2: u16 instead of u8 for the length.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 302a6ad7fc77146191126a1f3e2c5d724fd72416 upstream.
TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.
This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.
During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.
Fixes: aec04cbdf723 ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2998b02b2fb58f36ccbc318b00513174e9947d8e upstream.
The tpm stack uses pdev name convention for the parent device.
Fix that also in tpm_chip_alloc().
Fixes: 3897cd9c8d1d ("tpm: Split out the devm stuff from tpmm_chip_alloc")'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d761119a914ec0ac05ec2a5378d1f86e680967d upstream.
The error code handling is broken as any error code that has the same
bits set as TPM_RC_HASH passes. Implemented tpm2_rc_value() helper to
parse the error value from FMT0 and FMT1 error codes so that these types
of mistakes are prevented in the future.
Fixes: 5ca4c20cfd37 ("keys, trusted: select hash algorithm for TPM2 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d70fe9d9c3a4c627f9757cbba5d628687b121c1 upstream.
Since commit 1107d065fdf1 ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works. The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.
It turns out that until commit 8e54caf407b98e ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.
Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.
This is a backport for 4.9 kernel version of the original commit, with
renaming of "TPM_TIS_ITPM_POSSIBLE" flag removed since it was only a
cosmetic change and not a part of the real bug fix.
Fixes: 1107d065fdf1 ("tpm_tis: Introduce intermediate layer for TPM access")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5939eaf4f9d432586dd2cdeea778506471e8088e upstream.
Add the missing platform_driver_unregister() and remove the duplicate
platform_device_unregister(force_pdev) in the error handling case.
Fixes: 00194826e6be ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26a137e31ffe6fbfdb008554a8d9b3d55bd5c86e upstream.
If the TPM we're connecting to uses a static burst count, it will report
a burst count of zero throughout the response read. However, get_burstcount
assumes that a response of zero indicates that the TPM is not ready to
receive more data. In this case, it returns a negative error code, which
is passed on to tpm_tis_{write,read}_bytes as a u16, causing
them to read/write far too many bytes.
This patch checks for negative return codes and bails out from recv_data
and tpm_tis_send_data.
Fixes: 1107d065fdf1 (tpm_tis: Introduce intermediate layer for TPM access)
Signed-off-by: Josh Zimmerman <joshz@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f0f30e404b3d8f4597a2d9b77fba55452f8fd0e upstream.
tpm_chip_unregister can only be called after tpm_chip_register.
devm manages the allocation so no unwind is needed here.
Fixes: afb5abc262e96 ("tpm: two-phase chip management functions")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removal of this check was not properly amended to the original commit.
Cc: stable@vger.kernel.org
Fixes: 0c541332231e ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
This reverts commit e17acbbb69d30836a8c12e2c09bbefab8656693e.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This reverts commit 9514ff1961c6f0f5983ba72d94f384bc13e0d4a1.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This reverts commit 0c22db435bf79d3cf3089df7ff198d4867df3c27.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This reverts commit e350e24694e447e6ab7312fffae5ca31a0bb5165.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not enabled, the device will be in
ready state.
[jarkko.sakkinen@linux.intel.com: changed pm_runtime_put_sync()
to pm_runtime_put()]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
|
|
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
|
|
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.
The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.
Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'
To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
tpm_transmit() does not check that bufsiz is at least TPM_HEADER_SIZE
before accessing data. This commit adds this check and returns -EINVAL
if it fails.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Constify TPM 1.x header structures in order to move them to rodata
section as they are meant to be never changed during runtime.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Because of the line break in the debug print the chackpatch is
not silent on 80 characters limitation.
The easiest fix is to straighten the lines, it's also more readable.
WARNING: line over 80 characters
+ FW_BUG "TPM2 ACPI table does not define a memory
resource\n");
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Don't apply endianity conversion when writing to the registers
this is already handled by the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Instead of expensive register access on retrieving cmd_size
on each send, save the value during initialization in the private
context. The value doesn't change.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The platform device is not used in this driver, drop the
include to linux/platform_device.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Fixes the warning:
drivers/char/tpm/tpm_tis_core.c:443:7: warning: variable ‘itpm’ set but
not used [-Wunused-but-set-variable]
bool itpm;
^~~~
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
CRB_CTRL_CMD_READY and CRB_CTRL_GO_IDLE have incorrect values.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Renamed CRB protocol specific constants to match the TCG PC Client
Platform TPM Profile (PTP) Specification and driver status constants
to be explicit that they are driver specific.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
wmb()'s are not needed as iowrite32() is used.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.
The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:
* Cancel might not happen.
* req_canceled() always returns zero.
A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.
CC: stable@vger.kernel.org
Fixes: 30fc8d138e91 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Instead of a ad-hoc protocol message construction it is better to
call tpm_pcr_read_dev().
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
It is better to tpm_transmit_cmd() in tpm2_probe() in order to get
consistent command handling throughout the subsystem.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
Since tpm_gen_interrupt() is only used in tpm_tis_core.c this commit
replaces it with an internal tpm_tis_gen_interrupt(). The semantics
also changed in a way that on a system error the driver initialization
is failed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
Removed unnecessary externs from tpm.h.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
This function should only be called as part of an IRQ probing protocol
and st33 does not have any code to detect that the IRQ it tries to
generate was not generated and disable the IRQ.
Since st33 is primarily a DT binding driver it should not be doing
IRQ probing anyhow, so let us just delete this useless call.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.
Fixes: 0fe5480303a1 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
The driver emits invalid self test error message even though the init
succeeds.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: cae8b441fc20 ("tpm: Factor out common startup code")
Reviewed-by: James Morris <james.l.morris@oracle.com>
|
|
The command flow is exactly the same, the core simply needs to be
told to enable TPM2 mode when the compatible string indicates a
TPM2.
Signed-off-by: Andrew Azmansky <andrew.zamansky@nuvoton.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.
tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.
For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
If devm_add_action() fails we are explicitly calling put_device() to
free the resources allocated. Lets use the helper
devm_add_action_or_reset() and return directly in case of error, as we
know that the cleanup function has been already called by the helper if
there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In 570a3609 IRQ path is incorrectly always exercised while it should be
exercised only when there is an IRQ number allocated. This commit
reverts the old behavior.
[jarkko.sakkinen@linux.intel.com: updated description]
Fixes: 570a36097f3 ("tpm: drop 'irq' from struct tpm_vendor_specific")
Signed-off-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Some chips incorrectly support partial reads from TPM_STS register
at non-zero offsets. Read the entire 32-bits register instead of
making two 8-bit reads to support such devices and reduce the number
of bus transactions when obtaining the burstcount from TPM_STS.
Fixes: 27084efee0c3 ("tpm: driver for next generation TPM chips")
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
