| Age | Commit message (Collapse) | Author |
|---|
|
We used to drop policy->rwsem just before calling __cpufreq_governor()
in some cases earlier and so it was possible that __cpufreq_governor()
ran concurrently via separate threads for the same policy.
In order to guarantee valid state transitions for governors,
'governor_enabled' was required to be protected using some locking
and cpufreq_governor_lock was added for that.
But now __cpufreq_governor() is always called under policy->rwsem,
and 'governor_enabled' is protected against races even without
cpufreq_governor_lock.
Get rid of the extra lock now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Juri Lelli <juri.lelli@arm.com>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
[ rjw : Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq core code is not consistent with respect to invoking
__cpufreq_governor() under policy->rwsem.
Changing all code to always hold policy->rwsem around
__cpufreq_governor() invocations will allow us to remove
cpufreq_governor_lock that is used today because we can't
guarantee that __cpufreq_governor() isn't executed twice in
parallel for the same policy.
We should also ensure that policy->rwsem is held across governor
state changes.
For example, while adding a CPU to the policy in the CPU online path,
we need to stop the governor, change policy->cpus, start the governor
and then refresh its limits. The complete sequence must be guaranteed
to complete without interruptions by concurrent governor state
updates. That can be achieved by holding policy->rwsem around those
sequences of operations.
Also note that after this patch cpufreq_driver->stop_cpu() and
->exit() will get called under policy->rwsem which wasn't the case
earlier. That shouldn't have any side effects, though.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Juri Lelli <juri.lelli@arm.com>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 1aee40ac9c86 (cpufreq: Invoke __cpufreq_remove_dev_finish()
after releasing cpu_hotplug.lock) split the cpufreq's CPU offline
routine in two pieces, one of them to be run with CPU offline/online
locked and the other to be called later. The reason for that split
was a possible deadlock scenario involving cpufreq sysfs attributes
and CPU offline.
However, the handling of CPU offline in cpufreq has changed since
then. Policy sysfs attributes are never removed during CPU offline,
so there's no need to worry about accessing them during CPU offline,
because that can't lead to any deadlocks now. Governor sysfs
attributes are still removed in __cpufreq_governor(_EXIT), but
there is a new kobject type for them now and its show/store
callbacks don't lock CPU offline/online (they don't need to do
that).
This means that the CPU offline code in cpufreq doesn't need to
be split any more, so combine cpufreq_offline_prepare() with
cpufreq_offline_finish().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Changelog ]
Tested-by: Juri Lelli <juri.lelli@arm.com>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Earlier, when the struct freq-attr was used to represent governor
attributes, the standard cpufreq show/store sysfs attribute callbacks
were applied to the governor tunable attributes and they always acquire
the policy->rwsem lock before carrying out the operation. That could
have resulted in an ABBA deadlock if governor tunable attributes are
removed under policy->rwsem while one of them is being accessed
concurrently (if sysfs attributes removal wins the race, it will wait
for the access to complete with policy->rwsem held while the attribute
callback will block on policy->rwsem indefinitely).
We attempted to address this issue by dropping policy->rwsem around
governor tunable attributes removal (that is, around invocations of the
->governor callback with the event arg equal to CPUFREQ_GOV_POLICY_EXIT)
in cpufreq_set_policy(), but that opened up race conditions that had not
been possible with policy->rwsem held all the time.
The previous commit, "cpufreq: governor: New sysfs show/store callbacks
for governor tunables", fixed the original ABBA deadlock by adding new
governor specific show/store callbacks.
We don't have to drop rwsem around invocations of governor event
CPUFREQ_GOV_POLICY_EXIT anymore, and original fix can be reverted now.
Fixes: 955ef4833574 (cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reported-by: Juri Lelli <juri.lelli@arm.com>
Tested-by: Juri Lelli <juri.lelli@arm.com>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce a mechanism by which parts of the cpufreq subsystem
("setpolicy" drivers or the core) can register callbacks to be
executed from cpufreq_update_util() which is invoked by the
scheduler's update_load_avg() on CPU utilization changes.
This allows the "setpolicy" drivers to dispense with their timers
and do all of the computations they need and frequency/voltage
adjustments in the update_load_avg() code path, among other things.
The update_load_avg() changes were suggested by Peter Zijlstra.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
|
|
Drop a pointless label at a return statement from
__cpufreq_driver_target() and rearrange that function
to reduce the indentation level.
No intentional functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Signed-off-by: Eric Biggers <ebiggers3@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The comment has been incorrect since commit 4dea5806d332
("cpufreq: return EEXIST instead of EBUSY for second registering").
Signed-off-by: Eric Biggers <ebiggers3@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The show() and store() routines in the cpufreq core don't need to
check if the struct freq_attr they want to use really provides the
callbacks they need as expected (if that's not the case, it means
a bug in the code anyway), so change them to avoid doing that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The preprocessor magic used for setting the default cpufreq governor
(and for using the performance governor as a fallback one for that
matter) is really nasty, so replace it with __weak functions and
overrides.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Currently next_policy() explicitly checks if a policy is the last
policy in the cpufreq_policy_list. Use the standard list_is_last
primitive instead.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Notice that the boost_supported field in struct cpufreq_driver is
redundant, because the driver's ->set_boost callback may be left
unset if "boost" is not supported. Moreover, the only driver
populating the ->set_boost callback is acpi_cpufreq, so make it
avoid populating that callback if "boost" is not supported, rework
the core to check ->set_boost instead of boost_supported to
verify "boost" support and drop boost_supported which isn't
used any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
cpufreq_boost_supported() is not used outside of cpufreq.c, so make
it static.
While at it, refactor it as a one-liner (which it really is).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
For cpufreq drivers which use setpolicy interface, after offline->online
the policy is set to default. This can be reproduced by setting the
default policy of intel_pstate or longrun to ondemand and then change to
"performance". After offline and online, the setpolicy will be called with
the policy=ondemand.
For drivers using governors this condition is handled by storing
last_governor, during offline and restoring during online. The same should
be done for drivers using setpolicy interface. Storing last_policy during
offline and restoring during online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.
Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.
Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.
Fixes: 96bdda61f58b ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The sysfs policy directory is postfixed currently with the CPU number
for which the policy was created, which isn't necessarily the first CPU
in related_cpus mask.
To make it more consistent and predictable, lets postfix the policy with
the first cpu in related-cpus mask.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq sysfs interface had been a bit inconsistent as one of the
CPUs for a policy had a real directory within its sysfs 'cpuX' directory
and all other CPUs had links to it. That also made the code a bit
complex as we need to take care of moving the sysfs directory if the CPU
containing the real directory is getting physically hot-unplugged.
Solve this by creating 'policyX' directories (per-policy) in
/sys/devices/system/cpu/cpufreq/ directory, where X is the CPU for which
the policy was first created.
This also removes the need of keeping kobj_cpu and we can remove it now.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: is more of a general agreement from the person that he is
Reviewed-by: is a more strict tag and implies that the reviewer has
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
They don't do anything special now, remove the unnecessary wrapper.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Later patches will need to create policy specific directories in
/sys/devices/system/cpu/cpufreq/ directory and so the cpufreq directory
wouldn't be ever empty.
And so no fun creating/destroying it on need basis anymore. Create it
once on system boot.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
->related_cpus is empty at this point of time and copying ->cpus to it
or orring ->related_cpus with ->cpus would result in the same value. But
cpumask_copy makes it rather clear.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We just made sure policy->cpu is online and this check will always fail
as the policy is active. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When scaling_available_frequencies is read on an offlined cpu, then
either lockup or junk values are displayed. This is caused by
freed freq_table, which policy is using.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpufreq_cpu_get() called by get_cur_freq_on_cpu() is overkill,
because the ->get() callback is always invoked in a context in
which all of the conditions checked by cpufreq_cpu_get() are
guaranteed to be satisfied.
Use cpufreq_cpu_get_raw() instead of it and drop the
corresponding cpufreq_cpu_put() from get_cur_freq_on_cpu().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
* pm-cpufreq:
intel_pstate: fix PCT_TO_HWP macro
intel_pstate: Fix user input of min/max to legal policy region
cpufreq-dt: add suspend frequency support
cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
cpufreq: Use __func__ to print function's name
cpufreq: staticize cpufreq_cpu_get_raw()
cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
cpufreq: dt: Tolerance applies on both sides of target voltage
cpufreq: dt: Print error on failing to mark OPPs as shared
cpufreq: dt: Check OPP count before marking them shared
|
|
Some cpufreq drivers may set suspend frequency only for
selected setups but still would like to use the generic
suspend handler. Thus don't treat !policy->suspend_freq
condition as an incorrect one.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its better to use __func__ to print functions name instead of writing
the name in the print statement. This also has the advantage that a
change in function's name doesn't force us to change the print message
as well.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpufreq_cpu_get_raw() isn't used by any external users, staticize it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
|
|
* pm-opp:
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
PM / OPP: Free resources and properly return error on failure
cpufreq-dt: make scaling_boost_freqs sysfs attr available when boost is enabled
cpufreq: dt: Add support for turbo/boost mode
cpufreq: dt: Add support for operating-points-v2 bindings
cpufreq: Allow drivers to enable boost support after registering driver
cpufreq: Update boost flag while initializing freq table from OPPs
PM / OPP: add dev_pm_opp_is_turbo() helper
PM / OPP: Add helpers for initializing CPU OPPs
PM / OPP: Add support for opp-suspend
PM / OPP: Add OPP sharing information to OPP library
PM / OPP: Add clock-latency-ns support
PM / OPP: Add support to parse "operating-points-v2" bindings
PM / OPP: Break _opp_add_dynamic() into smaller functions
PM / OPP: Allocate dev_opp from _add_device_opp()
PM / OPP: Create _remove_device_opp() for freeing dev_opp
PM / OPP: Relocate few routines
PM / OPP: Create a directory for opp bindings
PM / OPP: Update bindings to make opp-hz a 64 bit value
|
|
Driver is guaranteed to be present on a call to cpufreq_parse_governor()
and there is no need to check for !cpufreq_driver. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its always same as policy->policy, and there is no need to keep another
copy of it. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its always same as policy->governor, and there is no need to keep
another copy of it. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
'user_policy' caches properties of a policy that are set by userspace.
And these must be updated only if cpufreq core was successful in
updating them based on request from user space.
In store_scaling_governor(), we are updating user_policy.policy and
user_policy.governor even if cpufreq_set_policy() failed. That's
incorrect.
Fix this by updating user_policy.* only if we were successful in
updating the properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpufreq_get_policy() is useful if the pointer to policy isn't available
in advance. But if it is available, then there is no need to call
cpufreq_get_policy(). Directly use memcpy() to copy the policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
What's being done from CPUFREQ_INCOMPATIBLE, can also be done with
CPUFREQ_ADJUST. There is nothing special with CPUFREQ_INCOMPATIBLE
notifier.
Kill CPUFREQ_INCOMPATIBLE and fix its usage sites.
This also updates the numbering of notifier events to remove holes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the new patches for the driver core / sysfs for 4.3-rc1.
Very small number of changes here, all the details are in the
shortlog, nothing major happening at all this kernel release, which is
nice to see"
* tag 'driver-core-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
bus: subsys: update return type of ->remove_dev() to void
driver core: correct device's shutdown order
driver core: fix docbook for device_private.device
selftests: firmware: skip timeout checks for kernels without user mode helper
kernel, cpu: Remove bogus __ref annotations
cpu: Remove bogus __ref annotation of cpu_subsys_online()
firmware: fix wrong memory deallocation in fw_add_devm_name()
sysfs.txt: update show method notes about sprintf/snprintf/scnprintf usage
devres: fix devres_get()
|
|
In some cases it wouldn't be known at time of driver registration, if
the driver needs to support boost frequencies.
For example, while getting boost information from DT with opp-v2
bindings, we need to parse the bindings for all the CPUs to know if
turbo/boost OPPs are supported or not.
One way out to do that efficiently is to delay supporting boost mode
(i.e. creating /sys/devices/system/cpu/cpufreq/boost file), until the
time OPP bindings are parsed.
At that point, the driver can enable boost support. This can be done at
->init(), where the frequency table is created.
To do that, the driver requires few APIs from cpufreq core that let him
do this. This patch provides these APIs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its return value is not used by the subsys core and nothing meaningful
can be done with it, even if we want to use it. The subsys device is
anyway getting removed.
Update prototype of ->remove_dev() to make its return type as void. Fix
all usage sites as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This check was originally added by commit 9c9a43ed2734 ("[CPUFREQ]
return error when failing to set minfreq").It attempt to return an error
on obviously incorrect limits when we echo xxx >.../scaling_max,min_freq
Actually we just need check if new_policy->min > new_policy->max.
Because at least one of max/min is copied from cpufreq_get_policy().
For example, when we echo xxx > .../scaling_min_freq, new_policy is
copied from policy in cpufreq_get_policy. new_policy->max is same with
policy->max. new_policy->min is set to a new value.
Let me explain it in deduction method, first statement in if ():
new_policy->min > policy->max
policy->max == new_policy->max
==> new_policy->min > new_policy->max
second statement in if():
new_policy->max < policy->min
policy->max < policy->min
==>new_policy->min > new_policy->max (induction method)
So we have proved that we only need check if new_policy->min >
new_policy->max.
After apply this patch, we can also modify ->min and ->max at same time
if new freq range is very much different from current freq range. For
example, if current freq range is 480000-960000, then we want to set
this range to 1120000-2240000, we would fail in the past because
new_policy->min > policy->max. As long as the cpufreq range is valid, we
has no reason to reject the user. So correct the check to avoid such
case.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To protect against races with concurrent CPU online/offline, call
get_online_cpus() before registering a cpufreq driver.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The recover_policy is unsed in cpufreq_online() to indicate whether
a new policy object is created or an existing one is reinitialized.
The "recover" part of the name is slightly confusing (it should be
"reinitialization" rather than "recovery") and the logical not (!)
operator is applied to it in almost all of the checks it is used in,
so replace that variable with a new one called "new_policy" that
will be true in the case of a new policy creation.
While at it, drop one of the labels that is jumped to from only
one spot.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
To separate the CPU online interface from the CPU device
registration, split cpufreq_online() out of cpufreq_add_dev()
and make cpufreq_cpu_callback() call the former, while
cpufreq_add_dev() itself will only be used as the CPU device
addition subsystem interface callback.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Change cpufreq_policy_alloc() to take a CPU number instead of a CPU
device pointer as its argument, as it is the only function called by
cpufreq_add_dev() taking a device pointer argument at this point.
That will allow us to split the CPU online part from cpufreq_add_dev()
more cleanly going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The related_cpus mask includes CPUs whose cpufreq_cpu_data per-CPU
pointers have been set the the given policy. Since those pointers
are only set at the policy creation time and unset when the policy
is deleted, the related_cpus should not be updated between those
two operations.
For this reason, avoid updating it whenever the first of the
"related" CPUs goes online.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev argument of cpufreq_add_policy_cpu() and
cpufreq_add_dev_interface() is not used by any of them,
so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The leftover out_release_rwsem label in cpufreq_add_dev() is not
necessary any more and confusing, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Notice that when cpufreq_policy_restore() is called, its per-CPU
cpufreq_cpu_data variable has been already dereferenced and if that
variable is not NULL, the policy local pointer in cpufreq_add_dev()
contains its value.
Therefore it is not necessary to dereference it again and the
policy pointer can be used directly. Moreover, if that pointer
is not NULL, the policy is inactive (or the previous check would
have made us return from cpufreq_add_dev()) so the restoration
code from cpufreq_policy_restore() can be moved to that point
in cpufreq_add_dev().
Do that and drop cpufreq_policy_restore().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Since __cpufreq_remove_dev_prepare() and __cpufreq_remove_dev_finish()
are about CPU offline rather than about CPU removal, rename them to
cpufreq_offline_prepare() and cpufreq_offline_finish(), respectively.
Also change their argument from a struct device pointer to a CPU
number, because they use the CPU number only internally anyway
and make them void as their return values are ignored.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
|
