summaryrefslogtreecommitdiff
path: root/drivers/dma
AgeCommit message (Collapse)Author
2016-02-15dmaengine: dw: disable BLOCK IRQs for non-cyclic xferAndy Shevchenko
The commit 2895b2cad6e7 ("dmaengine: dw: fix cyclic transfer callbacks") re-enabled BLOCK interrupts with regard to make cyclic transfers work. However, this change becomes a regression for non-cyclic transfers as interrupt counters under stress test had been grown enormously (approximately per 4-5 bytes in the UART loop back test). Taking into consideration above enable BLOCK interrupts if and only if channel is programmed to perform cyclic transfer. Fixes: 2895b2cad6e7 ("dmaengine: dw: fix cyclic transfer callbacks") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mans Rullgard <mans@mansr.com> Tested-by: Mans Rullgard <mans@mansr.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-02-08dmaengine: edma: fix residue race for cyclicJohn Ogness
When retrieving the residue value, the SRC/DST fields of the active PaRAM are read to determine the current position of the DMA engine. However, the AM335x Technical Reference Manual states: 11.3.3.6 Parameter Set Updates After the TR is read from the PaRAM (and is in the process of being submitted to the EDMA3TC), the following fields are updated as needed: ... SRC DST This means SRC/DST is incremented even though the DMA transfer may not have started yet or is in progress. Thus if the reader of the residue accesses the DMA buffer too quickly, the CPU is misinformed about the data that has been successfully processed. The CCSTAT.ACTV register is a boolean that is set if any TR is being processed by either the EMDA3CC or EDMA3TC. By polling this register it is possible to ensure that the residue value returned is valid for immediate processing. However, since the DMA engine may be active, polling may never hit a moment where no TR is being processed. To handle this, the SRC/DST is also polled to see if it changes. And as a last resort, a max loop count for the busy waiting exists to avoid an infinite loop. Signed-off-by: John Ogness <john.ogness@linutronix.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-02-08dmaengine: dw: pci: add ID for WildcatPoint PCHAndy Shevchenko
WildcatPoint PCH as seen on MacBook 12-inch (Early 2015) has PCI enabled DesignWare DMA controller. Enable it by adding its ID to the corresponding driver. Reported-by: Leif Liddy <leif.liddy@gmail.com> BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=110901 Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-30dmaengine: IOATDMA: fix timer code that continues to restart channels during ↵Dave Jiang
idle The timer_event() function seems to have a bug where it ends up marking the last entry as non-responding and eventually attempts to restart the channel. This also continuously happen when idle. What needs to happen is for us to make sure there are no descriptors active and then handle that case properly. We should only hit the "cleanup" stage if there are still active descriptors. Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-20Merge tag 'dmaengine-fix-4.5-rc1' of ↵Linus Torvalds
git://git.infradead.org/users/vkoul/slave-dma Pull dmaengine fixes from Vinod Koul: "Here is my second pull request for this window: A few driver fixes have piled up and one missed rcar bindings patch which got somehow lost in for-linus branch so cherry-picked that one. Fixes are for dw, at_hdmac, edma" * tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: dmaengine: rcar-dmac: Document SoC specific bindings dmaengine: at_xdmac: fix resume for cyclic transfers dmaengine: dw: fix cyclic transfer callbacks dmaengine: dw: fix cyclic transfer setup dmaengine: edma: Fix paRAM slot allocation for entry channel 0
2016-01-18dmaengine: at_xdmac: fix resume for cyclic transfersSongjun Wu
When having cyclic transfers, the channel was paused when performing suspend but was not correctly resumed. Signed-off-by: Songjun Wu <songjun.wu@atmel.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver") Cc: <stable@vger.kernel.org> # 4.1 and later Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-17Merge tag 'sound-4.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound updates from Takashi Iwai: "We've had quite busy weeks in this cycle. Looking at ALSA core, the significant changes are a few fixes wrt timer and sequencer ioctls that have been revealed by fuzzer recently. Other than that, ASoC core got a few updates about DAI link handling, but these are rather straightforward refactoring. In drivers scene, ASoC received quite lots of new drivers in addition to bunch of updates for still ongoing Intel Skylake support and topology API. HD-audio gained a new HDMI/DP hotplug notification via component. FireWire got a pile of code refactoring/updates with SCS.1x driver integration. More highlights are shown below. [ NOTE: this contains also many commits for DRM. This is due to the pull of drm stable branch into sound tree, as the base of i915 audio component work for HD-audio. The highlights below don't contain these DRM changes, as these are supposed to be pulled via drm tree in anyway sooner or later. ] Core: - Handful fixes to harden ALSA timer and sequencer ioctls against races reported by syzkaller fuzzer - Irq description string can be unique to each card; only for HD-audio for now ASoC: - Conversion of the array of DAI links to a list for supporting dynamically adding and removing DAI links - Topology API enhancements to make everything more component based and being able to specify PCM links via topology - Some more fixes for the topology code, though it is still not final and ready for enabling in production; we really need to get to the point where that can be done - A pile of changes for Intel SkyLake drivers which hopefully deliver some useful initial functionality for systems with this chipset, though there is more work still to come - Lots of new features and cleanups for the Renesas drivers - ANC support for WM5110 - New drivers: Imagination Technologies IPs, Atmel class D speaker, Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP - Rename PCM1792a driver to be generic pcm179x HD-Audio: - Use audio component for i915 HDMI/DP hotplug handling - On-demand binding with i915 driver - bdl_pos_adj parameter adjustment for Baytrail controllers - Enable power_save_node for CX20722; this shouldn't lead to regression, hopefully - Kabylake HDMI/DP codec support - Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell machines - A few code refactoring FireWire: - Lots of code cleanup and refactoring - Integrate the support of SCS.1x devices into snd-oxfw driver; snd-scs1x driver is obsoleted USB-audio: - Fix possible NULL dereference at disconnection - A regression fix for Native Instruments devices Misc: - A few code cleanups of fm801 driver" * tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (722 commits) ALSA: timer: Code cleanup ALSA: timer: Harden slave timer list handling ALSA: hda - Add fixup for Dell Latitidue E6540 ALSA: timer: Fix race among timer ioctls ALSA: hda - add codec support for Kabylake display audio codec ALSA: timer: Fix double unlink of active_list ALSA: usb-audio: Fix mixer ctl regression of Native Instrument devices ALSA: hda - fix the headset mic detection problem for a Dell laptop ALSA: hda - Fix white noise on Dell Latitude E5550 ALSA: hda_intel: add card number to irq description ALSA: seq: Fix race at timer setup and close ALSA: seq: Fix missing NULL check at remove_events ioctl ALSA: usb-audio: Avoid calling usb_autopm_put_interface() at disconnect ASoC: hdac_hdmi: remove unused hdac_hdmi_query_pin_connlist ASoC: AMD: Add missing include file ALSA: hda - Fixup inverted internal mic for Lenovo E50-80 ALSA: usb: Add native DSD support for Oppo HA-1 ASoC: Make aux_dev more like a generic component ASoC: bcm2835: cleanup includes by ordering them alphabetically ASoC: AMD: Manage ACP 2.x SRAM banks power ...
2016-01-14dmaengine: dw: fix cyclic transfer callbacksMans Rullgard
Cyclic transfer callbacks rely on block completion interrupts which were disabled in commit ff7b05f29fd4 ("dmaengine/dw_dmac: Don't handle block interrupts"). This re-enables block interrupts so the cyclic callbacks can work. Other transfer types are not affected as they set the INT_EN bit only on the last block. Fixes: ff7b05f29fd4 ("dmaengine/dw_dmac: Don't handle block interrupts") Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Cc: <stable@vger.kernel.org>
2016-01-14dmaengine: dw: fix cyclic transfer setupMans Rullgard
Commit 61e183f83069 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume") moved some channel initialisation to a new function which must be called before starting a transfer. This updates dw_dma_cyclic_start() to use dwc_dostart() like the other modes, thus ensuring dwc_initialize() gets called and removing some code duplication. Fixes: 61e183f83069 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume") Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Cc: <stable@vger.kernel.org>
2016-01-13Merge tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds
Pull dmaengine updates from Vinod Koul: "This round we have few new features, new driver and updates to few drivers. The new features to dmaengine core are: - Synchronized transfer termination API to terminate the dmaengine transfers in synchronized and async fashion as required by users. We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac drivers. - Universal API for channel request and start consolidation of request flows. It's user is ompa-dma driver. - Introduce reuse of descriptors and use in pxa_dma driver Add/Remove: - New STM32 DMA driver - Removal of unused R-Car HPB-DMAC driver Updates: - ti-dma-crossbar updates for supporting eDMA - tegra-apb pm updates - idma64 - mv_xor updates - ste_dma updates" * tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (54 commits) dmaengine: mv_xor: add suspend/resume support dmaengine: mv_xor: de-duplicate mv_chan_set_mode*() dmaengine: mv_xor: remove mv_xor_chan->current_type field dmaengine: omap-dma: Add support for DMA filter mapping to slave devices dmaengine: edma: Add support for DMA filter mapping to slave devices dmaengine: core: Introduce new, universal API to request a channel dmaengine: core: Move and merge the code paths using private_candidate dmaengine: core: Skip mask matching when it is not provided to private_candidate dmaengine: mdc: Correct terminate_all handling dmaengine: edma: Add probe callback to edma_tptc_driver dmaengine: dw: fix potential memory leak in dw_dma_parse_dt() dmaengine: stm32-dma: Fix unchecked deference of chan->desc dmaengine: sh: Remove unused R-Car HPB-DMAC driver dmaengine: usb-dmac: Document SoC specific compatibility strings ste_dma40: Delete an unnecessary variable initialisation in d40_probe() ste_dma40: Delete another unnecessary check in d40_probe() ste_dma40: Delete an unnecessary check before the function call "kmem_cache_destroy" dmaengine: tegra-apb: Free interrupts before killing tasklets dmaengine: tegra-apb: Update driver to use GFP_NOWAIT dmaengine: tegra-apb: Only save channel state for those in use ...
2016-01-13dmaengine: edma: Fix paRAM slot allocation for entry channel 0Peter Ujfalusi
edma_alloc_slot was not checking the channel mapping support existence when slot 0 has been requested (used as entry slot for channel/event 0). Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-12Merge branch 'acpi-soc'Rafael J. Wysocki
* acpi-soc: PM / clk: don't leave clocks enabled when driver not bound i2c: dw: Add APM X-Gene ACPI I2C device support ACPI / APD: Add APM X-Gene ACPI I2C device support ACPI / LPSS: change 'does not have' to 'has' in comment Revert "dmaengine: dw: platform: provide platform data for Intel" dmaengine: dw: return immediately from IRQ when DMA isn't in use dmaengine: dw: platform: power on device on shutdown ACPI / LPSS: override power state for LPSS DMA device ACPI / LPSS: power on when probe() and otherwise when remove() ACPI / LPSS: do delay for all LPSS devices when D3->D0 ACPI / LPSS: allow to use specific PM domain during ->probe() Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()" device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification x86/platform/iosf_mbi: Remove duplicate definitions Conflicts: drivers/i2c/busses/i2c-designware-platdrv.c
2016-01-07Revert "dmaengine: dw: platform: provide platform data for Intel"Andy Shevchenko
Since we have a work around to prevent a system hangup we don't need to provide a platform data explicitly anymore. This reverts commit 175267b389f781748e2bbb6c737e76b5c9bc4c88. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-01-07dmaengine: dw: return immediately from IRQ when DMA isn't in useAndy Shevchenko
There is no need to bother the hardware when all channels are idle. We have not to get any interrupts. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-01-07dmaengine: dw: platform: power on device on shutdownAndy Shevchenko
We have to call dw_dma_disable() to stop any ongoing transfer. On some platforms we can't do that since DMA device is powered off. Moreover we have no possibility at that point to check if the platform is affected or not. That's why we call pm_runtime_get_sync() / pm_runtime_put() unconditionally. On the other hand we can't use pm_runtime_suspended() because runtime PM framework is not fully used by the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-01-07dmaengine: xgene-dma: Fix double IRQ issue by setting IRQ_DISABLE_UNLAZY flagRameshwar Prasad Sahu
For interrupt controller that doesn't support irq_disable and hardware with level interrupt, an extra interrupt can be pending. This patch fixes the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line. Reference: http://git.kernel.org/tip/e9849777d0e27cdd2902805be51da73e7c79578c Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-06dmaengine: mv_xor: add suspend/resume supportThomas Petazzoni
This commit adds suspend/resume support to the mv_xor driver. The config and interrupt mask registers must be saved and restored, and upon resume, the MBus windows configuration must also be done again. Tested on Armada 388 GP, with a RAID 5 array, accessed before and after a suspend to RAM cycle. Based on work from Ofer Heifetz and Lior Amsalem. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-06dmaengine: mv_xor: de-duplicate mv_chan_set_mode*()Thomas Petazzoni
When commit 6f166312c6ea2 ("dmaengine: mv_xor: add support for a38x command in descriptor mode") added support for the descriptor mode available in Marvell Armada 38x and later SoCs, it added a new function mv_chan_set_mode_to_desc() which allows to configure a XOR channel to get the specific operation to be done from each individual DMA descriptor. However, this function was mainly a duplicate of the existing mv_chan_set_mode(), with just the operation being different. This commit re-organizes the code into a single mv_chan_set_mode() function, which takes the operation mode as argument, and the mv_xor_channel_add() function decides whether to use XOR_OPERATION_MODE_IN_DESC or XOR_OPERATION_MODE_XOR. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-06dmaengine: mv_xor: remove mv_xor_chan->current_type fieldThomas Petazzoni
Since commit 3e4f52e2da9f6 ("dma: mv_xor: Simplify the DMA_MEMCPY operation"), this field is no longer used, so get rid of it. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-01-06Merge branch 'topic/ti-xbar' into for-linusVinod Koul
2016-01-06Merge branch 'topic/tegra' into for-linusVinod Koul
2016-01-06Merge branch 'topic/stm32' into for-linusVinod Koul
2016-01-06Merge branch 'topic/ste' into for-linusVinod Koul
2016-01-06Merge branch 'topic/rcar' into for-linusVinod Koul
2016-01-06Merge branch 'topic/omap' into for-linusVinod Koul
2016-01-06Merge branch 'topic/ioatdma' into for-linusVinod Koul
2016-01-06Merge branch 'topic/idma' into for-linusVinod Koul
2016-01-06Merge branch 'topic/async' into for-linusVinod Koul
2016-01-06Merge branch 'topic/univ_api' into for-linusVinod Koul
2016-01-06Merge branch 'topic/desc_reuse' into for-linusVinod Koul
2016-01-06dmaengine: Revert "dmaengine: mic_x100: add missing spin_unlock"Ashutosh Dixit
This reverts commit e958e079e254 ("dmaengine: mic_x100: add missing spin_unlock"). The above patch is incorrect. There is nothing wrong with the original code. The spin_lock is acquired in the "prep" functions and released in "submit". Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-23Merge remote-tracking branches 'asoc/topic/samsung', 'asoc/topic/sh', ↵Mark Brown
'asoc/topic/ssm2518' and 'asoc/topic/sti' into asoc-next
2015-12-18dmaengine: omap-dma: Add support for DMA filter mapping to slave devicesPeter Ujfalusi
Add support for providing device to filter_fn mapping so client drivers can switch to use the dma_request_chan() API. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: edma: Add support for DMA filter mapping to slave devicesPeter Ujfalusi
Add support for providing device to filter_fn mapping so client drivers can switch to use the dma_request_chan() API. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: core: Introduce new, universal API to request a channelPeter Ujfalusi
The two API function can cover most, if not all current APIs used to request a channel. With minimal effort dmaengine drivers, platforms and dmaengine user drivers can be converted to use the two function. struct dma_chan *dma_request_chan_by_mask(const dma_cap_mask_t *mask); To request any channel matching with the requested capabilities, can be used to request channel for memcpy, memset, xor, etc where no hardware synchronization is needed. struct dma_chan *dma_request_chan(struct device *dev, const char *name); To request a slave channel. The dma_request_chan() will try to find the channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode it will use a filter lookup table and retrieves the needed information from the dma_slave_map provided by the DMA drivers. This legacy mode needs changes in platform code, in dmaengine drivers and finally the dmaengine user drivers can be converted: For each dmaengine driver an array of DMA device, slave and the parameter for the filter function needs to be added: static const struct dma_slave_map da830_edma_map[] = { { "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 0) }, { "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 1) }, { "davinci-mcasp.1", "rx", EDMA_FILTER_PARAM(0, 2) }, { "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 3) }, { "davinci-mcasp.2", "rx", EDMA_FILTER_PARAM(0, 4) }, { "davinci-mcasp.2", "tx", EDMA_FILTER_PARAM(0, 5) }, { "spi_davinci.0", "rx", EDMA_FILTER_PARAM(0, 14) }, { "spi_davinci.0", "tx", EDMA_FILTER_PARAM(0, 15) }, { "da830-mmc.0", "rx", EDMA_FILTER_PARAM(0, 16) }, { "da830-mmc.0", "tx", EDMA_FILTER_PARAM(0, 17) }, { "spi_davinci.1", "rx", EDMA_FILTER_PARAM(0, 18) }, { "spi_davinci.1", "tx", EDMA_FILTER_PARAM(0, 19) }, }; This information is going to be needed by the dmaengine driver, so modification to the platform_data is needed, and the driver map should be added to the pdata of the DMA driver: da8xx_edma0_pdata.slave_map = da830_edma_map; da8xx_edma0_pdata.slavecnt = ARRAY_SIZE(da830_edma_map); The DMA driver then needs to configure the needed device -> filter_fn mapping before it registers with dma_async_device_register() : ecc->dma_slave.filter_map.map = info->slave_map; ecc->dma_slave.filter_map.mapcnt = info->slavecnt; ecc->dma_slave.filter_map.fn = edma_filter_fn; When neither DT or ACPI lookup is available the dma_request_chan() will try to match the requester's device name with the filter_map's list of device names, when a match found it will use the information from the dma_slave_map to get the channel with the dma_get_channel() internal function. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: core: Move and merge the code paths using private_candidatePeter Ujfalusi
Channel matching with private_candidate() is used in two paths, the error checking is slightly different in them and they are duplicating code also. Move the code under find_candidate() to provide consistent execution and going to allow us to reuse this mode of channel lookup later. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: core: Skip mask matching when it is not provided to private_candidatePeter Ujfalusi
If mask is NULL skip the mask matching against the DMA device capabilities. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: mdc: Correct terminate_all handlingDamien.Horsley
Use of the CANCEL bit in mdc_terminate_all creates an additional 'command done' to appear in the registers (in addition to an interrupt). In addition, there is a potential race between mdc_terminate_all and the irq handler if a transfer completes at the same time as the terminate all (presently this results in an inappropriate warning). To handle these issues, any outstanding 'command done' events are cleared during mdc_terminate_all and the irq handler takes no action when there are no new 'command done' events. Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: edma: Add probe callback to edma_tptc_driverPeter Ujfalusi
Due to changes in device and platform code drivers w/o probe will fail to load. This means that the devices for eDMA TPTCs are goign to be without driver and omap hwmod code will turn them off after the kernel finished loading: [ 3.015900] platform 49800000.tptc: omap_device_late_idle: enabled but no driver. Idling [ 3.024671] platform 49a00000.tptc: omap_device_late_idle: enabled but no driver. Idling This will prevent eDMA to work since the TPTCs are not enabled. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Fixes: 34635b1accb9 ("dmaengine: edma: Add dummy driver skeleton for edma3-tptc") Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-18dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()Mans Rullgard
If the "dma-channels" DT property is missing, the dw_dma_parse_dt() function return NULL, but not before allocating memory for a struct dw_dma_platform_data through devres. If the device supports parameter detection, the probe still succeeds and the allocated memory is not released until the device is removed. Fix this by deferring the allocation until after checking the "dma-channels" property. Signed-off-by: Mans Rullgard <mans@mansr.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10dmaengine: at_xdmac: fix at_xdmac_prep_dma_memcpy()Cyrille Pitchen
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field of the Channel Configuration register was not updated properly in the loop: the bits of the dwidth field were not cleared before adding their new value. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: e1f7c9eee70 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver") Cc: stable@vger.kernel.org #4.1 and later Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10dmaengine: stm32-dma: Fix unchecked deference of chan->descM'boumba Cedric Madianga
'commit d8b468394fb7 ("dmaengine: Add STM32 DMA driver")' leads to the following Smatch complaint: drivers/dma/stm32-dma.c:562 stm32_dma_issue_pending() error: we previously assumed 'chan->desc' could be null (see line 560) So, this patch fixes the unchecked dereference of chan->desc by returning operation not permitted error when stm32_dma_start_transfer() does not succeed to allocate a virtual channel descriptor. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10dmaengine: sh: Remove unused R-Car HPB-DMAC driverGeert Uytterhoeven
As of commit 4baadb9e05c68962 ("ARM: shmobile: r8a7778: remove obsolete setup code"), the Renesas R-Car HPB-DMAC driver is no longer used. In theory it could still be used on R-Car Gen1 SoCs, but that requires adding DT support to the driver, which is not planned. Remove the driver, it can be resurrected from git history when needed. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10ste_dma40: Delete an unnecessary variable initialisation in d40_probe()Markus Elfring
The variable "res" will eventually be set to a resource pointer from a call of the d40_hw_detect_init(() function. Thus let us omit the explicit initialisation at the beginning. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10ste_dma40: Delete another unnecessary check in d40_probe()Markus Elfring
A single jump label was used by the d40_probe() function in several cases for error handling which was a bit inefficient here. * This implementation detail could be improved by the introduction of another jump label. * Remove an extra check for the variable "base". * Omit its explicit initialisation at the beginning then. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10ste_dma40: Delete an unnecessary check before the function call ↵Markus Elfring
"kmem_cache_destroy" The kmem_cache_destroy() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10Merge branch 'fix/edma' into fixesVinod Koul
2015-12-10dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit typePeter Ujfalusi
This change makes the DT file to be easier to read since the reserved slots array does not need the '/bits/ 16' to be specified, which might confuse some people. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-10dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit typePeter Ujfalusi
This change makes the DT file to be easier to read since the memcpy channels array does not need the '/bits/ 16' to be specified, which might confuse some people. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-12-05dmaengine: tegra-apb: Free interrupts before killing taskletsJon Hunter
On probe failure or driver removal, before killing any tasklets, ensure that the channel interrupt is freed to ensure that another channel interrupt cannot occur and schedule the tasklet again. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>