| Age | Commit message (Collapse) | Author |
|---|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The statements BUG_ON(ctx == 0) was implicitly casting a pointer
to an integer for comparison. Do this with a bool test instead
to get away from sparse warnings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch enables suspend and resume mode for the power management, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch enables 'debounce' for the designware GPIO, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch replaces 'readl&writel' with 'dwapb_read&dwapb_write'.
Reviewed-by: Shevchenko, Andriy <andriy.shevchenko@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Synopsys DesignWare APB GPIO driver only supports open firmware devices.
But, like Intel Quark X1000 SOC, which has a single PCI function exporting
a GPIO and an I2C controller, it is a Multifunction device. This patch is
to enable the current Synopsys DesignWare APB GPIO driver to support the
Multifunction device which exports the designware GPIO controller.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: abdoulaye berthe <berthe.ab@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Right new have one irq chip running always in level mode. It would nicer
to have two irq chips where one is handling level type interrupts and
the other one is doing edge interrupts. So we can have at runtime two users
where one is using edge and the other level.
Acked-by: Alan Tull <delicious.quinoa@gmail.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver calls irq_alloc_domain_generic_chips() which creates a gc and
adds it to gc_list. The driver later then calls irq_setup_generic_chip()
which also initializes the gc and adds it to the gc_list() and this
corrupts the list. Enable LIST_DEBUG and you see the kernel complain.
This isn't required, irq_alloc_domain_generic_chips() did the init.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alan Tull <delicious.quinoa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This switches all GPIO and pin control drivers with irqchips
that were using .startup() and .shutdown() callbacks to lock
GPIO lines for IRQ usage over to using the .request_resources()
and .release_resources() callbacks just introduced into the
irqchip vtable.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Synopsys DesignWare block is used in some ARM devices (picoxcell)
and can be configured to provide multiple banks of GPIO pins.
v12: - Add irq_startup/shutdown
- do irq_create_mapping() in probe, irq_find_mapping() in to_irq()
- Adjust mappings to show support for 1 gpio per port.
- gpio-cells = <1>
v11: - Use NULL when checking existence of 'interrupts' property
- Bindings descriptions cleanup
v10: - in documentation nr-gpio -> nr-gpios
v9: - cleanup in dt bindings doc
- use of_get_child_count()
v8: - remove socfpga.dtsi changes
- minor cleanup in devicetree documentation
v7: - use irq_generic_chip
- support one irq per gpio line or one irq for many
- s/bank/port/ and other cleanup
v6: - (atull) squash the set of patches
- use linear irq domain
- build fixes. Original driver was reviewed on v3.2.
- Fix setting irq edge type for 'rising' and 'both'.
- Support as a loadable module.
- Use bgpio_chip's spinlock during register access.
- Clean up register names to match spec
- s/bank/port/ because register names use the word 'port'
- s/nr-gpio/nr-gpios/
- don't get/put the of_node
- remove signoffs/acked-by's because of changes
- other cleanup
v5: - handle sparse bank population correctly
v3: - depend on rather than select IRQ_DOMAIN
- split IRQ support into a separate patch
v2: - use Rob Herring's irqdomain in generic irq chip patches
- use reg property to indicate bank index
- support irqs on both edges based on LinusW's u300 driver
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Alan Tull <atull@altera.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
