| Age | Commit message (Collapse) | Author |
|---|
|
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm: rcar-du: Implement support for interlaced modes
drm: rcar-du: Clamp DPMS states to on and off
drm: rcar-du: Enable hotplug detection on HDMI connector
drm: rcar-du: Output HSYNC instead of CSYNC
drm: rcar-du: Add support for external pixel clock
drm: rcar-du: Refactor DEFR8 feature
drm: rcar-du: Remove LVDS and HDMI encoders chaining restriction
drm: rcar-du: Configure pitch for chroma plane of multiplanar formats
drm: rcar-du: Don't fail probe in case of partial encoder init error
drm: adv7511: Remove interlaced mode check
|
|
Accept interlaced modes on the VGA and HDMI connectors and configure the
hardware accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The intermediate DPMS standby and suspend states are a thing from the
past. They only matter in practice for VGA CRT monitors, and are just a
power saving vs. resume time optimization. Given that they have never
been implemented properly in the rcar-du driver and that the Intel
driver has dropped them on the vga port years ago, it's safe to only
care about the on and off states.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
As HDMI support hotplug detection, enable HPD-based poll on HDMI
connectors.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The DU outputs by default a composite sync signal (XOR of the horizontal
and vertical sync signals) on the HSYNC output pin. As this can confuse
devices and isn't needed by any of the supported encoders, configure the
HSYNC pin to output the horizontal sync signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The DU uses the module functional clock as the default pixel clock, but
supports using an externally supplied pixel clock instead. Support this
by adding the external pixel clock to the DT bindings, and selecting the
clock automatically at runtime based on the requested mode pixel
frequency.
The input clock pins to DU channels routing is configurable, but
currently hardcoded to connect input clock i to channel i.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Rename the feature from RCAR_DU_FEATURE_DEFR8 to
RCAR_DU_FEATURE_EXT_CTRL_REGS to cover all extended control registers in
addition to the DEFR8 register.
Usage of the feature is refactored to optimize runtime operation and
prepare for external clock support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The rcar-du driver refuses connecting an LVDS output to an HDMI encoder.
There is not technical reason for that restriction, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The PnMWR register containing the plane stride must be programmed with
correct stride values for both the luma and chroma planes when using a
multiplanar format. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
If an encoder fails to initialize the device can still be used without
the failed encoder. Don't propagate the error out of the probe function
but just skip the failed encoder.
As a special case a deferred probe request from the encoder is still
propagated out of the probe function in order not to break the deferred
probing mechanism.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
|
|
The DRM connector's encoder pointer is managed internally by the DRM
core and set to NULL when the DRM connector is disconnected from the
CRTC it was attached to. This results in a NULL pointer dereference in
the HDMI connector functions when trying to call the associated slave
encoder's operations.
Fix this by retrieving the slave encoder pointer from the R-Car
connector structure instead of the DRM connector structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
SoCs that integrate the DU have no internal HDMI encoder, support
external encoders only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
DRM slave encoders require their associated struct drm_encoder instance
to be embedded in a struct drm_slave_encoder. This makes processing
encoders regardless of their types needlessly and painfully complex in
drivers that use a mix of slave encoders and custom encoders. Such a
driver will need to either create drm_slave_encoder instances that fake
their embedded encoder instance, or to turn all drm_encoder instances
into drm_slave_encoder instances.
Between the two evils, one must choose the lesser. Use drm_slave_encoder
everywhere.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Add a new macro to downcast an rcar_du_encoder pointer to a drm_encoder
pointer and use it. This prepares for the replacement of the
rcar_drm_encoder encoder field with a drm_slave_encoder.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The encoder DT node will be needed to register an external HDMI encoder.
Pass it to the rcar_du_encoder_init() function to prepare for HDMI
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
All platforms now instantiate the DU through DT, platform data support
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Propagate the error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
git://people.freedesktop.org/~tagr/linux into drm-next
drm: Sanitize DRM_IOCTL_MODE_CREATE_DUMB input
Some drivers erroneously treat the .pitch and .size fields of struct
drm_mode_create_dumb as inputs. While the include/uapi/drm/drm_mode.h
header has a comment denoting them as outputs, that seemingly wasn't
enough to make drivers use them properly.
The result is that some userspace doesn't explicitly zero out those
fields, assuming that the kernel won't use them. That causes problems
since the data within the structure might be uninitialized, so bogus
data may end up confusing drivers (ridiculously large values for the
pitch, ...).
This series attempts to improve the situation by fixing all drivers to
not use the output fields. Furthermore to spare new drivers this bad
surprise, the DRM core now zeros out these fields prior to handing the
data structure to the driver.
Lessons learned from this are that future IOCTLs should be properly
documented (in the DRM DocBook for example) and should be rigorously
defined. To prevent misuse like this, userspace should be required to
zero out all output fields. The kernel should check for this and fail
if that's not the case.
* tag 'drm/gem-cma/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux:
drm/cma: Remove call to drm_gem_free_mmap_offset()
drm: Sanitize DRM_IOCTL_MODE_CREATE_DUMB input
drm/rcar: gem: dumb: pitch is an output
drm/omap: gem: dumb: pitch is an output
drm/cma: Introduce drm_gem_cma_dumb_create_internal()
drm/doc: Add GEM/CMA helpers to kerneldoc
drm/doc: mm: Fix indentation
drm/gem: Fix a few kerneldoc typos
|
|
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags fields are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size.
Drivers must not treat these values as possible inputs, otherwise they
may use uninitialized memory during the computation of the framebuffer
size.
The R-Car DU driver treats the pitch passed in from userspace as minimum
and will only overwrite it when the driver-computed pitch is larger,
allowing userspace to, intentionally or not, overallocate framebuffers.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This function is similar to drm_gem_cma_dumb_create() but targetted at
kernel internal users so that they can override the pitch and size
requirements of the dumb buffer.
It is important to make this difference because the IOCTL says that the
pitch and size fields are to be considered outputs and therefore should
not be used in computations of the framebuffer size. Internal users may
still want to use this code to avoid duplication and at the same time
pass on additional, driver-specific restrictions on the pitch and size.
While at it, convert the R-Car DU driver, the single user that overrides
the pitch, to use the new internal helper.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Implement support for the R-Car DU DT bindings in the rcar-du DRM
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
In preparation for DT support where panel timings will be described by a
DRM-agnostic video mode, replace the struct drm_mode_modeinfo instance
in the panel platform data with a struct videomode.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The "Renesas Corporation" listed in the copyright notice doesn't exist.
Replace it with "Renesas Electronics Corporation" and update the
copyright years.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The maximum pitch constraint for the hardware is expressed in pixels.
Convert it to bytes to validate frame buffer creation, as frame buffer
pitches are expressed in bytes.
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drivers/gpu/drm/rcar-du/rcar_du_drv.c:190:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
Always use #ifdef with CONFIG symbols, never just bare #if
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The Renesas R-Car Display Unit driver is only useful on shmobile
unless build testing. The LVDS output is useful on an even more
reduced hardware set.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The rcar_du_encoder_init() function can fail and return an error code.
Don't ignore it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
rcar misc changes.
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add support for the r8a7791 DU
drm/rcar-du: Add LVDS_LANES quirk
drm/rcar-du: Split features and quirks
drm/rcar-du: Update plane pitch in .mode_set_base() operation
drm/rcar-du: Don't cast crtc to rcrtc twice in the same function
drm/rcar-du: fix return value check in rcar_du_lvdsenc_get_resources()
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR(). Also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Remove the unneeded mem == NULL check]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The magic dance drm_platform_exit does is actually a remnant of the
old legacy shadow attach support for platform devices. Modern modesetting
drm drivers shouldn't do this any more (and usb/pci devices actually don't
do this).
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The r8a7791 DU is a stripped-down version of the r8a7790 DU with two
CRTCs and a single LVDS output.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
LVDS lanes 1 and 3 are switched in ES1 hardware (R8A7790). The problem
has been fixed in newer revisions, add a quirk to make the workaround
selectable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
128-byte pitch alignement is not a hardware feature, it's a hardware
bug. Split it from the features field into a new quirks field. New
quirks will be added to support the R8A7791 SoC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
When setting a new frame buffer with the mode set base operation the
pitch value might change. Set the hardware plane pitch register at the
same time as the plane base address in the rcar_du_plane_update_base()
function to make sure the pitch value always matches the frame buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Reuse the previously cast variable instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR(). Also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
|
|
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Merge the rcar stable branch that is being shared with the arm-soc tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* pfdo/drm-rcar-for-v3.12: (220 commits)
drm/rcar-du: Add FBDEV emulation support
drm/rcar-du: Add internal LVDS encoder support
drm/rcar-du: Configure RGB output routing to DPAD0
drm/rcar-du: Rework output routing support
drm/rcar-du: Add support for DEFR8 register
drm/rcar-du: Add support for multiple groups
drm/rcar-du: Fix buffer pitch alignment for R8A7790 DU
drm/rcar-du: Add support for the R8A7790 DU
drm/rcar-du: Move output routing configuration to group
drm/rcar-du: Remove register definitions for the second channel
drm/rcar-du: Use dynamic number of CRTCs instead of CRTCs array size
drm/rcar-du: Introduce CRTCs groups
drm/rcar-du: Rename rcar_du_plane_(init|register) to rcar_du_planes_*
drm/rcar-du: Create rcar_du_planes structure
drm/rcar-du: Rename platform data fields to match what they describe
drm/rcar-du: Merge LVDS and VGA encoder code
drm/rcar-du: Split VGA encoder and connector
drm/rcar-du: Split LVDS encoder and connector
drm/rcar-du: Clarify comment regarding plane Y source coordinate
drm/rcar-du: Support per-CRTC clock and IRQ
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/qxl/qxl_release.c
|
|
Use the FB CMA helpers to implement FBDEV emulation support. The VGA
connector status must be reported as connector_status_connected instead
of connector_status_unknown to be usable by the emulation layer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The R8A7790 includes two internal LVDS encoders. Support them in the DU
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The R8A7790 DU variant has a single RGB output called DPAD0 that can be
fed with the output of DU0, DU1 or DU2. Making the routing configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
