| Age | Commit message (Collapse) | Author |
|---|
|
Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.
The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.
sysfs: cannot create duplicate filename
'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78
This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.
Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors")
Fixes: ea98b29a05e9 ("hwmon: Support sensors exported via ARM SCP interface")
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:
drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'
This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.
CC [M] drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build. Select it by default
in Kconfig.
Reported-by: Guo Chunrong <B40290@freescale.com>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Fixes: a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull tiny hwmon update from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Remove duplicate pci-id define
|
|
PCI_DEVICE_ID_AMD_15H_M60H_NB_F3 is now defined in pci_ids.h
Signed-off-by: Adam Majer <adamm@zombino.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina:
"Trivial stuff from trivial tree that can be trivially summed up as:
- treewide drop of spurious unlikely() before IS_ERR() from Viresh
Kumar
- cosmetic fixes (that don't really affect basic functionality of the
driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek
- various comment / printk fixes and updates all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
bcache: Really show state of work pending bit
hwmon: applesmc: fix comment typos
Kconfig: remove comment about scsi_wait_scan module
class_find_device: fix reference to argument "match"
debugfs: document that debugfs_remove*() accepts NULL and error values
net: Drop unlikely before IS_ERR(_OR_NULL)
mm: Drop unlikely before IS_ERR(_OR_NULL)
fs: Drop unlikely before IS_ERR(_OR_NULL)
drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
UBI: Update comments to reflect UBI_METAONLY flag
pktcdvd: drop null test before destroy functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
|
|
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
|
|
This patch adds a member in fam15h_power_data which specifies the
maximum accumulated power in a compute unit.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch enables power1_input attribute for Carrizo platform.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Attributes depend on the CPU model the driver gets loaded on.
Therefore, add those attributes dynamically at init time. This is more
flexible to control the different attributes on different platforms.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
NCT6792 and NCT6793 are mostly register compatible to NCT6791, but
temperature sources are different and difficult to manage with a single
temperature label array. Introduce separate temperature label arrays
for those chips to reflect the differences.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Both NCT6791D and NCT6792D permit selection of a 'virtual' temperature
register as temperature source. The virtual temperature registers are
registers 0xea to 0xef in bank 0 and can be written by software.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
when checking for the value of the shunt resistor.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Any sysfs "show" read access from the client app will result in reading
all registers (8 with ina226). Depending on the host this can limit the
best achievable read rate.
This changeset allows for individual register accesses through regmap.
Tested with BeagleBone Black (Baylibre-ACME) and ina226.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
|
|
A new limit selected arbitrarily as power of two greater than
required minimum for Xeon Phi processor (72 for Knights Landing).
Currently driver is not able to handle cores with core ID greater than 32.
Such attempt ends up with the following error in dmesg:
coretemp coretemp.0: Adding Core XXX failed
Signed-off-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The TMP75C has a different control register layout and only supports
12-bit temperature samples (0.0625 deg C).
The continuous sample rate is ~12 Hz.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix module autoload for IBM and Open power platforms.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The description in the driver states: "ABX500 does not provide auto ADC,
so to monitor the required temperatures, a periodic work is used. It is
more important to not wake up the CPU... If the chip gets too hot during
a sleep state it's most likely due to external factors, such as the
surrounding temperature and nothing can be done in S/W."
So it makes no sense to keep IRQs enabled as it need not be wakeup
source. This patch removes the use of IRQF_NO_SUSPEND flag
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
max31790_update_device() return the error code in ERR_PTR. We were
checking if it has returned error or not but before checking we have
dereferenced it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver supports the Maxim MAX31790.
Signed-off-by: Il Han <corone.il.han@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support to create thermal zones based on the temperature sensors
provided by the SCP. The thermal zones can be defined using the
thermal DT bindings and should refer to the SCP sensor id to select
the sensor.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
|
|
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
|
|
s/ressources/resources/
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The STEP_UP_TIME and STEP_DOWN_TIME registers are swapped for all chips but
NCT6775.
Reported-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
|
|
|
|
This patch adds a member (cpu_pwr_sample_ratio) of fam15h_power_data,
that represents the ratio of compute unit power accumulator sample
period to the PTSC counter period.
Tsample: compute unit power accumulator sample period
Tref: the performance timestamp counter period
PTSC: performance timestamp counter
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTM2975 is a dual 9A or single 18A μModule regulator.
It is register compatible with LTM4676.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Some of the LTC chips supported by this driver have to be polled
to ensure that they are ready to accept commands.
Signed-off-by: Michael Jones <mike@proclivis.com>
[Guenter Roeck: simplifications and formatting changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
PMBus controllers optionally support PEC. Configure the driver
to use it if available to improve operational security.
Suggested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Using the BIT macro makes the code a little easier to read.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add additional chip ID for an older revision of LTC2978, as well
as two chip IDs for LTC3882. Turns out the LTC3882 does support the
LTC2978_MFR_SPECIAL_ID register, and reading it returns its chip ID,
but the register is undocumented.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Per information from Linear Technologies, the ID mask is 12 bit
for all chips of this series. Use this mask to detect chips to ensure
that all chip revisions are detected.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The code used to determine historic low and high peaks is repeated
several times. Introduce helper functions to simplify it.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
It is becoming cumbersom to track per-chip feature support.
Introduce feature flag to simplify the code.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
