summaryrefslogtreecommitdiff
path: root/drivers/i2c
AgeCommit message (Collapse)Author
2016-01-14Merge branch 'i2c/for-4.5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "Quite some driver updates: - piix4 can now handle multiplexed adapters - brcmstb, xlr, eg20t, designware drivers support more SoCs - emev2 gained i2c slave support - img-scb and rcar got bigger refactoring to remove issues - lots of common driver updates i2c core changes: - new quirk flag when an adapter does not support clock stretching, so clients can be configured to avoid that if possible - added a helper function to retrieve timing parameters from firmware (with rcar being the first user) - "multi-master" DT binding added so drivers can adapt to this setting (like disabling PM to keep arbitration working) - RuntimePM for the logical adapter device is now always enabled by the core to ensure propagation from childs to the parent (the HW device) - new macro builtin_i2c_driver to reduce boilerplate" * 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits) i2c: create builtin_i2c_driver to avoid registration boilerplate i2c: imx: fix i2c resource leak with dma transfer dt-bindings: i2c: eeprom: add another EEPROM device dt-bindings: move I2C eeprom descriptions to the proper file i2c: designware: Do not require clock when SSCN and FFCN are provided DT: i2c: trivial-devices: Add Epson RX8010 and MPL3115 i2c: s3c2410: remove superfluous runtime PM calls i2c: always enable RuntimePM for the adapter device i2c: designware: retry transfer on transient failure i2c: ibm_iic: rename i2c_timings struct due to clash with generic version i2c: designware: Add support for AMD Seattle I2C i2c: imx: Remove unneeded comments i2c: st: use to_platform_device() i2c: designware: use to_pci_dev() i2c: brcmstb: Adding support for CM and DSL SoCs i2c: mediatek: fix i2c multi transfer issue in high speed mode i2c: imx: improve code readability i2c: imx: Improve message log when DMA is not used i2c: imx: add runtime pm support to improve the performance i2c: imx: init bus recovery info before adding i2c adapter ...
2016-01-12Merge branch 'acpi-soc'Rafael J. Wysocki
* acpi-soc: PM / clk: don't leave clocks enabled when driver not bound i2c: dw: Add APM X-Gene ACPI I2C device support ACPI / APD: Add APM X-Gene ACPI I2C device support ACPI / LPSS: change 'does not have' to 'has' in comment Revert "dmaengine: dw: platform: provide platform data for Intel" dmaengine: dw: return immediately from IRQ when DMA isn't in use dmaengine: dw: platform: power on device on shutdown ACPI / LPSS: override power state for LPSS DMA device ACPI / LPSS: power on when probe() and otherwise when remove() ACPI / LPSS: do delay for all LPSS devices when D3->D0 ACPI / LPSS: allow to use specific PM domain during ->probe() Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()" device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification x86/platform/iosf_mbi: Remove duplicate definitions Conflicts: drivers/i2c/busses/i2c-designware-platdrv.c
2016-01-12Merge branch 'device-properties'Rafael J. Wysocki
* device-properties: device property: avoid allocations of 0 length device property: the secondary fwnode needs to depend on the primary device property: add spaces to PROPERTY_ENTRY_STRING macro include/linux/property.h: fix build issues with gcc-4.4.4 i2c: designware: Convert to use unified device property API mfd: intel-lpss: Pass HSUART configuration via properties mfd: intel-lpss: Pass SDA hold time to I2C host controller driver mfd: intel-lpss: Add support for passing device properties mfd: core: propagate device properties to sub devices drivers driver core: Do not overwrite secondary fwnode with NULL if it is set driver core: platform: Add support for built-in device properties device property: Take a copy of the property set device property: Fallback to secondary fwnode if primary misses the property device property: return -EINVAL when property isn't found in ACPI device property: improve readability of macros device property: helper macros for property entry creation device property: keep single value inplace device property: refactor built-in properties support device property: rename helper functions device property: always check for fwnode type
2016-01-10i2c: imx: fix i2c resource leak with dma transferGao Pan
In i2c_imx_dma_xfer(), when dmaengine_submit() returns error, the context goto label err_submit and then return. However, the memory allocated for txdesc has not been freed yet, which leads to resource leak. Signed-off-by: Gao Pan <b54642@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10i2c: designware: Do not require clock when SSCN and FFCN are providedSuravee Suthikulpanit
The current driver uses input clock source frequency to calculate values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not currently have a good way to provide the frequency information. Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used to directly provide these values. So, the clock information should no longer be required during probing. However, since clk can be invalid, additional checks must be done where we are making use of it. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Tested-by: Loc Ho <lho@apm.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10i2c: s3c2410: remove superfluous runtime PM callsWolfram Sang
RuntimePM of the adapter device is now taken care of by the core. So, we can remove these calls. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10i2c: always enable RuntimePM for the adapter deviceWolfram Sang
The adapter device is a logical device. Because of that, it already uses pm_runtime_no_callbacks() in the core. To ensure proper propagation from the children (i2c devices) to the parent of the adapter (the HW device), make sure RuntimePM is enabled in any case. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10i2c: designware: retry transfer on transient failureBaruch Siach
Set the i2c_adapter retries field to a sensible value. This allows the i2c core to retry master_xfer() when it returns -EAGAIN. Currently the i2c-designware driver returns -EAGAIN only on Tx arbitration failure (DW_IC_TX_ARB_LOST). Reported-by: Rolland Chau <zourongrong@gmail.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-07i2c: dw: Add APM X-Gene ACPI I2C device supportLoc Ho
Enable APM X-Gene ACPI I2C device support by adding the corresponding ACPI ID. The platform ACPI APD corresponding change is required to provide the proper clock frequency input. Signed-off-by: Loc Ho <lho@apm.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-01-05i2c: ibm_iic: rename i2c_timings struct due to clash with generic versionStephen Rothwell
Fixes: e1dba01ca620 ("i2c: add generic routine to parse DT for timing information") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-04i2c: designware: Add support for AMD Seattle I2CSuravee Suthikulpanit
Add device HID AMDI0510 to match the I2C controlers on AMD Seattle platform Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-04i2c: imx: Remove unneeded commentsFabio Estevam
These multi-lines comments do not follow the standard kernel coding style. In fact, they are not useful comments, so get rid of them. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: st: use to_platform_device()Geliang Tang
Use to_platform_device() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: designware: use to_pci_dev()Geliang Tang
Use to_pci_dev() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: brcmstb: Adding support for CM and DSL SoCsKamal Dasu
Broadcoms DSL, CM (cable modem)and STB I2C core implementation have 8 data in/out registers that can transfer 8 bytes or 32 bytes max. Cable and DSL "Peripheral" i2c cores use single byte per data register and the STB can use 4 byte per data register transfer. Adding support to take care of this difference. Accordingly added the compatible string for SoCs using the "Peripheral" I2C block. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: mediatek: fix i2c multi transfer issue in high speed modeLiguo Zhang
For mt8173 platform with auto restart support, when doing i2c multi transfer in high speed, we should ignore the first restart irq after the master code, otherwise the first transfer will be discarded. Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com> Reviewed-by: Eddie Huang <eddie.huang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: imx: improve code readabilityGao Pan
Replace of_get_named_gpio_flags with of_get_named_gpio because the latter has less parameters, which improves code readability. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Gao Pan <b54642@freescale.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: imx: Improve message log when DMA is not usedFabio Estevam
When DMA cannot be used, it is better to state that the I2C controller will operate in PIO mode. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: imx: add runtime pm support to improve the performanceGao Pan
In our former i2c driver, i2c clk is enabled and disabled in xfer function, which contributes to power saving. However, the clk enable process brings a busy wait delay until the core is stable. As a result, the performance is sacrificed. To weigh the power consumption and i2c bus performance, runtime pm is the good solution for it. The clk is enabled when a i2c transfer starts, and disabled after a specifically defined delay. If CONFIG_PM is disabled the net result of this patch is that the clock is never disabled. Without the patch the test case (many eeprom reads) executes with approx: real 1m7.735s user 0m0.488s sys 0m20.040s With the patch the same test case (many eeprom reads) executes with approx: real 0m54.241s user 0m0.440s sys 0m5.920s Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Gao Pan <b54642@freescale.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [wsa: sorted includes] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03i2c: imx: init bus recovery info before adding i2c adapterGao Pan
During driver probe, i2c_imx_init_recovery_info() must come before i2c_add_numbered_adapter(), because the get/set_scl() functions are assigned in i2c_register_adapter() under the conditon that bus recover_info are initialized. Otherwise, get/set_scl() function pointers never get assigned. In such case, when i2c_generic_gpio_recovery() is used for bus recovery, there will be kernel crash because bri->set_scl is NULL. The solution to this bug is moving i2c_imx_init_recovery_info() before i2c_register_adapter(). Signed-off-by: Gao Pan <b54642@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2016-01-02i2c: rcar: disable PM in multi-master modeWolfram Sang
In multi master mode, the IP core needs to be always active for arbitration reasons. Get the config from DT and set up PM depending on the config. Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02i2c: rcar: remove macros dealing with flagsWolfram Sang
These macros don't really hide complexity, but C idioms. Removing them makes the code easier to read IMO and make a planned extension easier. Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02i2c: img-scb: support repeated starts on IP v3.3Sifan Naeem
In version 3.3 of the IP when transaction halt is set, an interrupt will be generated after each byte of a transfer instead of after every transfer but before the stop bit. Due to this behaviour we have to be careful that every time we release the transaction halt we have to re-enable it straight away so that we only process a single byte, not doing so will result in all remaining bytes been processed and a stop bit being issued, which will prevent us having a repeated start. This change will have no effect on earlier versions of the IP. Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Acked-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: James Hartley <james.hartley@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02i2c: img-scb: add handle for Master halt interruptSifan Naeem
Master halt is issued after each byte of a transaction is processed in IP version 3.3. Master halt will stall the bus by holding the SCK line low until the halt bit in the scb_general_control is cleared. After the last byte of a transfer is processed we can use the Master Halt interrupt to facilitate a repeated start transfer without issuing a stop bit. Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Reviewed-by: James Hartley <james.hartley@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02i2c: img-scb: add handle for stop detected interruptSifan Naeem
Stop Detected interrupt is triggered when a Stop bit is detected on the bus, which indicates the end of the current transfer. When the end of a transfer is indicated by the Stop Detected interrupt, drain the FIFO and signal completion for the transaction. Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02i2c: img-scb: remove fifo EMPTYING interrupts handleSifan Naeem
Now that we are using the transaction halt interrupt to safely control repeated start transfers, we no longer need to handle the fifo emptying interrupts. Handling this interrupt along with Transaction Halt interrupt can cause erratic behaviour. Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02i2c: img-scb: support I2C_M_IGNORE_NAKSifan Naeem
This commit adds support for the I2C_M_IGNORE_NAK protocol modification. Such behaviour can only be implemented in atomic mode. So, if a transaction contains a message with such flag the drivers switches to atomic mode. The implementation consists simply in treating NAKs as ACKs. Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Acked-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: James Hartley <james.hartley@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-19i2c: rcar: disable runtime PM correctly in slave modeWolfram Sang
When we also are I2C slave, we need to disable runtime PM because the address detection mechanism needs to be active all the time. However, we can reenable runtime PM once the slave instance was unregistered. So, use pm_runtime_get_sync/put to achieve this, since it has proper refcounting. pm_runtime_allow/forbid is like a global knob controllable from userspace which is unsuitable here. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2015-12-17i2c: make i2c_parse_fw_timings() always visibleWolfram Sang
This function used to be DT only, so it lived inside a CONFIG_OF block. Now it uses device attributes and must be moved outside of it. No further code changes, only one whitespace improvement. Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-17i2c: emev: select I2C slave supportWolfram Sang
Until we have proper support to make I2C slave support fully optional, select it to prevent build errors on randconfigs. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-16i2c: xlr: add interrupt support for Sigma Designs chipsMåns Rullgård
The Sigma Designs variant of this controller has the ability to generate interrupts. This is controlled using two additional registers, oddly enough overlapping with the defined but unused HDSTATIM. This patch adds support for using this feature instead of busy-looping if an IRQ is specified. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-16i2c: xlr: fix extra read/write at end of rx transferMåns Rullgård
The BYTECNT register holds the transfer size minus one. Setting it to the correct value removes the need for a dummy read/write at the end of each transfer. As zero-length transfers are not supported, do not advertise I2C_FUNC_SMBUS_QUICK. In other words, this patch makes the driver transfer the number of bytes requested unless this is zero, which is not supported by the hardware and is thus refused. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-15i2c: xlr: add support for Sigma Designs controller variantMåns Rullgård
Sigma Designs chips use a variant of this controller with the following differences: - The BUSY bit in the STATUS register is inverted - Bit 8 of the CONFIG register must be set - The controller can generate interrupts This patch adds support for the first two of these. It also calculates and sets the correct clock divisor if a clk is provided. The bus frequency is optionally speficied in the device tree node. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: uniphier_f: error out if bus speed is zeroMasahiro Yamada
There is code to divide by "bus_speed" some lines below. To eliminate the possibility of division by zero, bail out if "clock-frequency" is specified as zero. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: uniphier_f: error out if clock rate is zeroMasahiro Yamada
This input clock is used to generate the sampling clock for I2C bus. If the clock rate is zero, there is something wrong with the clock driver. Bail out with the appropriate error message in such a case. It would make it easier to find the root cause of failure. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: uniphier: error out if bus speed is zeroMasahiro Yamada
There is code to divide by "bus_speed" some lines below. To eliminate the possibility of division by zero, bail out if "clock-frequency" is specified as zero. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: uniphier: error out if clock rate is zeroMasahiro Yamada
This input clock is used to generate the sampling clock for I2C bus. If the clock rate is zero, there is something wrong with the clock driver. Bail out with the appropriate error message in such a case. It would make it easier to find the root cause of failure. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: rcar: honor additional i2c timings from DTWolfram Sang
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: rcar: switch to i2c generic dt parsingWolfram Sang
Switch to the new generic functions. Plain convert, no functionality added yet. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: rcar: refactor probe function a littleWolfram Sang
The probe function is a little bit messy, something here, something there. Rework it so that there is some order: first init the private structure, then the adapter, then do HW init. This also allows us to remove the device argument of the clock calculation function, because it now can be deduced from the private structure. Also, shorten some lines where possible. This is a preparation for further refactoring. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14i2c: add generic routine to parse DT for timing informationWolfram Sang
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and extended. See built-in docs for further information. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-12i2c: designware: Keep pm_runtime_enable/_disable calls in syncJarkko Nikula
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the runtime PM disable depth keeps increasing over repeated modprobe/rmmod cycle because pm_runtime_disable() is called without checking should it be disabled already because of bus sharing. This hasn't made any other harm than dev->power.disable_depth keeps increasing but keep it sync by calling pm_runtime_disable() only when runtime PM is not disabled. Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-12i2c: designware: fix IO timeout issue for AMD controllerXiangliang Yu
Because of some hardware limitation, AMD I2C controller can't trigger pending interrupt if interrupt status has been changed after clearing interrupt status bits. Then, I2C will lost interrupt and IO timeout. According to hardware design, this patch implements a workaround to disable i2c controller interrupt and re-enable i2c interrupt before exiting ISR. To reduce the performance impacts on other vendors, use unlikely function to check flag in ISR. Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2015-12-09i2c: imx: init bus recovery info before adding i2c adapterGao Pan
During driver probe, i2c_imx_init_recovery_info() must come before i2c_add_numbered_adapter(), because the get/set_scl() functions are assigned in i2c_register_adapter() under the conditon that bus recover_info are initialized. Otherwise, get/set_scl() function pointers never get assigned. In such case, when i2c_generic_gpio_recovery() is used for bus recovery, there will be kernel crash because bri->set_scl is NULL. The solution to this bug is moving i2c_imx_init_recovery_info() before i2c_register_adapter(). Signed-off-by: Gao Pan <b54642@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2015-12-09x86/platform/iosf_mbi: Remove duplicate definitionsAndy Shevchenko
The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-12-07i2c: designware: Convert to use unified device property APIMika Westerberg
With ACPI _DSD (introduced in ACPI v5.1) it is now possible to pass device configuration information from ACPI in addition to DT. In order to support this, convert the driver to use the unified device property accessors instead of DT specific. Change to ordering a bit so that we first try platform data and if that's not available look from device properties. ACPI *CNT methods are then used as last resort to override everything else. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-12-05i2c: emev2: add slave supportNiklas Söderlund
Add I2C slave provider using the generic slave interface. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-03i2c: eg20t: allow build on MIPS platformsPaul Burton
Allow the eg20t I2C driver to be built for MIPS platforms, in preparation for use on the MIPS Boston board. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-03i2c: eg20t: set i2c_adapter->dev.of_nodePaul Burton
Set the I2C adapter devices of_node to that of the PCI device, such that I2C clients may be instantiated via device tree. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-03i2c: at91: add support for the HOLD fieldLudovic Desroches
The hold field allows to configure the data hold time which can be set with the help of the generic binding 'i2c-sda-hold-time-ns'. This feature has been introduced with SAMA5D4 SoC family. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>