| Age | Commit message (Collapse) | Author |
|---|
|
Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).
Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Bart:
- drive-by CodingStyle fixups
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Delete filenames/versions from comments.
I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.
While at it:
* Remove unused VERSION define from ide.c.
* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.
While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Convert cmd64x, hpt366 and pdc202xx_old host drivers to use
pci_resource_start(hwif->pci_dev, 4) instead of hwif->dma_master.
* Remove no longer needed ->dma_master field from ide_hwif_t.
v2:
* Use the more readable 'hwif->dma_base - (hwif->channel * 8)' instead of
pci_resource_start(hwif->pci_dev, 4).
v3:
* Use hwif->extra_base in hpt366/pdc20xx_old + some cosmetic fixups over v2
(suggested by Sergei).
v4:
* Correct offsets in hpt3xxn_set_clock().
v5:
* Use hwif->extra_base in hpt366 for _real_ this time. (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename struct ide_pci_device_s to struct ide_port_info.
* Remove ide_pci_device_t typedef.
While at it:
* Fix __ide_pci_register_driver() comment.
* Fix aec62xx_init_one() comment.
* Remove unused 'cds' field from ide_hwgroup_t.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add IDE_HFLAG_RQSIZE_256 host flag to tell ide_pci_setup_ports() to set
hwif->rqsize to 256 sectors. Convert pdc202xx_old host driver to use it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:
generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method
it821x.c:
* if memory allocation fails drive->autotune won't be set
(but there also won't be ->set_pio_mode method in such case)
piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)
However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead
of hwif->err_stops_fifo. As a side-effect this change fixes
hwif->err_stops_fifo not being restored by ide_hwif_restore().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Split off pdc202ata4_fixup_irq() helper from init_setup_pdc202ata4().
* Merge init_setup_{pdc202ata4,pdc20265,pdc202xx}() into pdc202xx_init_one().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.
* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
method may still override them).
* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.
While at it:
* Use ATA_{UDMA,MWDMA,SWDMA}* defines.
* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.
* serverworks.c: fix DMA masks being set before checking DMA base.
v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Documentation doesn't mention SWDMA and moreover all timings used
for SWDMA modes were over-clocked when compared to ATA spec.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
and convert all users accordingly.
* Remove no longer needed ide_pio_data_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.
* Add IDE_HFLAG_SINGLE flag for single channel devices.
* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
and remove no longer needed ide_pci_device_t.channels field.
v2:
* Fix issues noticed by Sergei:
- correct code alignment in scc_pata.c
- s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Various old IDE drivers go mapping ROM devices for no apparent reason and
without using the ROM mapping API we now have. They don't actually use
the ROM they map and the new libata drivers are happy without it being
mapped so rather than port them lets just junk it for the next -rc1.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
|
|
Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:
- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;
- in au1xxx-ide.c, get rid of commented out printk();
- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:
- in aec62xx.c, rename the method in accordance with other drivers, and get rid
of unnecessary variables there;
- in pdc202xx_old.c, define/use 'hwif' variable;
- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Use ide_tune_dma() in ide-cris/it821x/pdc202xx_old/serverworks drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.
Rewrite mode programming code:
* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
even if both devices on the channel are not DMA capable and after reset
* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
as they need to be setup correctly also for PIO only devices, plus IORDY
wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
ATAPI devices
* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
(driver sets ->autotune to 1 so PIO modes are always programmed => lower
nibble of register A never equals 4 => "chipset_is_set" is always true)
* enable PIO mode programming for all ATAPI devices
(it was limited to ->media == ide_cdrom devices)
* remove extra reads of registers A/B/C, don't read register D et all
* do clearing / programming of registers A/B/C in one go
(gets rid of extra PCI config space read/write cycle)
* set initial values of drive_conf/AP/BP/CP variables to zero
(paranoia for the case when PCI reads fail)
* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
(ide_rate_filter() takes care of it)
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
* add FIXME comment about missing locking for 66MHz clock register
Also while at it:
* remove unused defines
* do a few cosmetic / CodingStyle fixes
* bump driver version
v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
registers is used only by the debugging code so cover "drive_conf"
PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
(Noticed by Sergei Shtylyov)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...
* print user-friendly warning about limiting the maximum transfer speed
to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
also while at it cleanup eighty_ninty_three() a bit
* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
- bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
(please see FIXME comment in eighty_ninty_three() for more details)
- CONFIG_IDEDMA_IVB=y/n cases were interchanged
- check for SATA devices was missing
* remove private cable warnings from pdc_202xx{old,new} drivers now that core
code provides this functionality (plus, in pdc202xx_new case the test could
give false warnings for ATAPI devices because pdc202xx_new driver doesn't
even support ATAPI DMA)
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.
* add ide_hwif_t.udma_filter hook for filtering UDMA mask
(use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
(loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()
v2:
* rename ->filter_udma_mask to ->udma_filter
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
(alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
filtering method - done in the next patch)
v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* piix: use hwif->cds->udma_mask
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
If DMA is unsupported ->ide_dma_check should disable DMA.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
CONFIG_PDC202XX_MASTER config option doesn't exist
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix the driver's tuneproc() method to always set the PIO mode requested and not
pick the best possible one, rename it to pdc202xx_tune_drive(), and change the
calls to it accordingly; remove the preceding comment which has nothing to do
with the code.
Sergei Shtylyov wrote:
> The tuneproc() method should take arg 255 for auto-selecting the best PIO
> mode, not 5 as it did here + this driver's method always auto-selected instead
> of setting the mode it's been told to -- issue typical to drivers/ide/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fold check_in_drive_lists() into quirkproc() handler in both PDC202xx
drivers-- this function was never called with a list other than
pdc_quirk_drives and was a bad example of code overall...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
