| Age | Commit message (Collapse) | Author |
|---|
|
This adds supply regulator handling for the VDD and IOVDD inputs
on the KXSD9 component, makes sure to bring the regulators online
during probe and disable them on remove or the errorpath.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
There are some hardcoded register values etc in the code, define
proper bitfield definitions, and use them when getting and setting
the scale. Optimize a read/modify/write to use regmap_update_bits()
at the same time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
As is custom with all modern sensors, add a clever burst mode
that will just stream out values from the sensor and provide it
to userspace to do the proper offsetting and scaling.
This is the result when tested with an HRTimer trigger:
$ generic_buffer -a -c 10 -n kxsd9 -t foo
/sys/bus/iio/devices/iio:device1 foo
0.371318 0.718680 9.869872 1795.000000 97545896129
-0.586922 0.179670 9.378775 2398.000000 97555864721
-0.299450 0.179670 10.348992 2672.000000 97565874055
0.371318 0.335384 11.103606 2816.000000 97575883240
0.179670 0.574944 10.540640 2847.000000 97585862351
0.335384 0.754614 9.953718 2840.000000 97595872425
0.179670 0.754614 10.732288 2879.000000 97605882351
0.000000 0.754614 10.348992 2872.000000 97615891832
-0.730658 0.574944 9.570422 2831.000000 97625871536
0.000000 1.137910 10.732288 2872.000000 97635881610
Columns shown are x, y, z acceleration, so a positive acceleration
of ~9.81 (shaky due to bad calibration) along the z axis. The
fourth column is the AUX IN which is floating on this system,
it seems to float up to the 2.85V VDD voltage.
To be able to cleanup the triggered buffer, we need to add .remove()
callbacks to the I2C and SPI subdrivers and call back into an
exported .remove() callback in the core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This fixes several errors in the offset and scaling of the raw
values from the KXSD9 sensor:
- The code did not convert the big endian value from the sensor
into the endianness of the host CPU. Fix this with
be16_to_cpu() on the raw obtained value.
- The code did not regard the fact that only the upper 12 bits of
the accelerometer values are valid. Shift these
down four bits to yield the real raw value.
- Further the sensor provides 2048 at zero g. This means that an
offset of 2048 must be subtracted from the raw value before
scaling. This was not taken into account by the driver,
yielding a weird value. Fix this by providing this offset in
sysfs.
To house the scaling code better, the value reading code was
factored into the raw reading function.
This proper scaling and offseting is necessary to get proper
values out of triggered buffer by offsetting, shifting and scaling
them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The RX/TX buffers are gone so drop the lock (it should have been
in the transport struct anyway).
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds I2C regmap transport for the KXSD9 driver.
Tested on the KXSD9 sensor on the APQ8060 Dragonboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This converts the KXSD9 driver to drop the custom transport
mechanism and just use regmap like everything else.
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This is just a masquerading register write function, so use the
register write function instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This moves the KXSD9 SPI transport out to its own file and Kconfig
entry, so that we will be able to add another transport method.
We export the common probe and add a local header file for the
functionality shared between the main driver and the transport
driver.
We make the SPI transport the default for the driver if SPI is
available and the KXSD9 driver was selected, so the oldconfig
upgrade path will be clear.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This makes it possible to later split the transport mechanism
using a generic probe() and a generic remove().
Use dev_set_drvdata() and dev_get_drvdata() as a paired
accessor to operate on the abstract struct device * regardless
of the transport mechanism in use.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Split off a transport mechanism struct that will deal with the SPI
traffic in preparation for adding I2C support.
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
|
|
The initial commit adding support for the mxc6225 assumed the
mxc6225 has a chip-id of 0xe5 based on testing on a single Allwinner
A23 tablet with a mxc6225. Testing on a bunch of other Allwinner
tablets have shown that the chip-id for the mxc6225 is not constant.
A datasheet for the MXC6255 which I've found online says that bits
7 and 6 of the chip-id register are undefined (for the mxc6255), testing
on 5 different tablets with a mxc6225 has found the following ids:
0x25, 0x45, 0x65, 0x85, 0xe5. So it seems that for the mxc6225 bits
7, 6 and 5 of the chip-id register are undefined.
This commit adjusts the chip-id check so that the mxc6255 driver
properly recognizes the mxc6225 in all these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We need the IIO changes in here for future patches to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ST sensors can be used as a trigger for its own triggered buffer
but it is also possible to use an external trigger: a HRTimer or
even a different sensor (!) as trigger. In that case we should not
pick the timestamp from our own interrupt top half even if it is
active.
This could practically happen if some other sensor is using the
ST sensor as trigger but the ST sensor itself is using e.g.
an HRTimer as trigger. So the trigger is on, but not used by us.
We used to assume that whenever the hardware interrupt is turned
on, we are using it for our own trigger, but this is an
oversimplification.
Handle this logically by using the iio_trigger_using_own() helper.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds a helper function to the IIO trigger framework:
iio_trigger_using_own(): for an IIO device, this tells
whether the device is using itself as a trigger.
This is true if the indio device:
(A) supplies a trigger and
(B) has assigned its own buffer poll function to use this
trigger.
This helper function is good when constructing triggered,
buffered drivers that can either use its own hardware *OR*
an external trigger such as a HRTimer or even the trigger from
a totally different sensor.
Under such circumstances it is important to know for example
if the timestamp from the same trigger hardware should be used
when populating the buffer: if iio_trigger_using_own() is true,
we can use this timestamp, else we need to pick a unique
timestamp directly in the trigger handler.
For this to work of course IIO devices registering hardware
triggers must follow the convention to set the parent device
properly, as as well as setting the parent of the IIO device
itself.
When a new poll function is attached, we check if the parent
device of the IIO of the poll function is the same as the
parent device of the trigger and in that case we conclude that
the hardware is using itself as trigger.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
iio_push_event() operates on a struct iio_dev. This struct can be allocated
using iio_device_alloc() which returns a valid struct iio_dev pointer. But
iio_push_event() is not safe to use on such a iio_dev until
iio_device_register() for the same device has successfully completed.
This restriction is not documented anywhere and most drivers are written
with the assumption that this restriction does not exist. The basic pattern
that is followed by all drivers looks like the following:
irqreturn_t event_callback(int irq, void *devid)
{
struct iio_dev *indio_dev = devid;
...
iio_push_event(indio_dev, ...);
return IRQ_HANDLED;
}
int driver_probe(struct device *dev)
{
struct iio_dev *indio_dev;
indio_dev = iio_device_alloc(...);
request_irq(event_irq, event_callback, ..., indio_dev);
return iio_device_register(indio_dev);
}
And while it is unlikely that the IRQ fires before iio_device_register()
completes (e.g. because the IRQ is disabled in the device) it is not
impossible and might be triggered by glitches on the signal line or
incorrect hardware configuration.
To avoid undefined behaviour in such a case extend iio_push_event() to
check if the event has been registered and discard generated events if it
has not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.8 cycle.
We have a big rework of the kxsd9 driver queued up behind the fix below and
a fix for a recent fix that was marked for stable.
Hence this fix series is perhaps a little more urgent than average for IIO.
* core
- a fix for a fix in the last set. The recent fix for blocking ops when
! task running left a path (unlikely one) in which the function return
value was not set - so initialise it to 0.
- The IIO_TYPE_FRACTIONAL code previously didn't cope with negative
fractions. Turned out a fix for this was in Analog's tree but hadn't made
it upstream.
* bmc150
- reset chip at init time. At least one board out there ends up coming up
in an unstable state due to noise during power up. The reset does no
harm on other boards.
* kxsd9
- Fix a bug in the reported scaling due to failing to set the integer
part to 0.
* hid-sensors-pressure
- Output was in the wrong units to comply with the IIO ABI.
* tools
- iio_generic_buffer: Fix the trigger-less mode by ensuring we don't fault
out for having no trigger when we explicitly said we didn't want to have
one.
|
|
7985e7c100 ("iio: Introduce a new fractional value type") introduced a
new IIO_VAL_FRACTIONAL value type meant to represent rational type numbers
expressed by a numerator and denominator combination.
Formating of IIO_VAL_FRACTIONAL values relies upon do_div() usage. This
fails handling negative values properly since parameters are reevaluated
as unsigned values.
Fix this by using div_s64_rem() instead. Computed integer part will carry
properly signed value. Formatted fractional part will always be positive.
Fixes: 7985e7c100 ("iio: Introduce a new fractional value type")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The mxc6225 is fully compatible with the existing mxc6255 driver,
add support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
On newer components compatible with the at91sam9x5, the Touchscreen
Switches Closure Time or TSSCTIM value of the Touchscreen Mode Register is
not filled at all.
On some hardware, having no time indicated for it may lead to incoherent
values and jitter.
We fix this time to 10us as it is usually difficult to retrieve impedance
values from LCD manufacturers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit aeb55fff3891834e07a3144159a7298a19696af8 ("iio:
st_sensors: fetch and enable regulators unconditionally"). Because
changes made in this patch are actually reference generators they should
be using devm_regulator_get_optional, but if they do not explicitly set
the reference to NULL they should not be using IS_ERR_OR_NULL, but
simple IS_ERR check.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit aeb55fff3891834e07a3144159a7298a19696af8 ("iio: st_sensors: fetch and enable regulators unconditionally").
The explanation for this change is same as in that patch:
"Supplies are *not* optional (optional means that the supply is
optional in the electrical sense, not the software sense) so we need to
get the and enable them at all times.
If the device tree or board file does not define suitable regulators for
the component, it will be substituted by a dummy regulator, or, if
regulators are disabled altogether, by stubs. There is no need to use the
IS_ERR_OR_NULL() check that is considered harmful.
Reported-by: Linus Wallerij <linus.walleij@linaro.org>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
A recent fix to iio_buffer_read_first_n_outer removed ret from being set by
a return from wait_event_interruptible and also added a continue in a loop
which causes the variable ret to not be set when it reaches the end of the
loop. Fix this by initializing ret to zero.
Also remove extraneous white space at the end of the loop.
Fixes: fcf68f3c0bb2a5 ("fix sched WARNING "do not call blocking ops when !TASK_RUNNING")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the staging fixes in here as well to handle merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add resource managed devm_iio_triggered_buffer_setup() and
devm_iio_triggered_buffer_cleanup() to automatically clean up triggered
buffers setup by IIO drivers, thus leading to simplified IIO drivers code.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add resource managed devm_iio_trigger_register() and
devm_iio_triger_unregister() to automatically clean up registered triggers
allocated by IIO drivers, thus leading to simplified IIO drivers code.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 4.8-rc5.
The largest thing here is deleting an obsolete driver,
drivers/misc/bh1780gli.c, as the functionality of it was replaced by
an iio driver a while ago.
The other fixes are things that have been reported, or reverts of
broken stuff (the binder change). All of these changes have been in
linux-next for a while with no reported issues"
* tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Don't declare Falcon Ridge unsupported
thunderbolt: Add support for INTEL_FALCON_RIDGE_2C controller.
thunderbolt: Fix resume quirk for Falcon Ridge 4C.
lkdtm: Mark lkdtm_rodata_do_nothing() notrace
mei: me: disable driver on SPT SPS firmware
Revert "android: binder: fix dangling pointer comparison"
drivers/iio/light/Kconfig: SENSORS_BH1780 cleanup
android: binder: fix dangling pointer comparison
misc: delete bh1780 driver
|
|
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
$cat in_accel_scale
-1057462640.011978
Fix this by assigning zero to the integer part.
Cc: stable@vger.kernel.org
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
drivers/iio/chemical/vz89x.c:119:9-10: WARNING: return of 0/1 in function 'vz89x_measurement_is_valid' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
CC: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In at least one known setup, the chip comes up in a state where reading
the chip ID returns garbage unless it's been reset, due to noise on the
wires during system boot.
All supported chips have the same reset method, and based on the
datasheets they all need 1.3 or 1.8ms to recover after reset. So, do
the conservative thing here and always reset the chip.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We were checking the return code of vdd when we should be checking
vdd_io. My mistake, mea culpa.
Cc: Giuseppe BARBA <giuseppe.barba@st.com>
Reported-by: Giuseppe BARBA <giuseppe.barba@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.
Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.
This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.
The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
According to IIO ABI definition, IIO_PRESSURE data output unit is
kilopascal:
http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio
This patch fix output unit of HID pressure sensor IIO driver from pascal to
kilopascal to follow IIO ABI definition.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
commit 1961bce76452 "iio: ina2xx: Remove trace_printk debug
statements" removed the code that used the chip->prev_ns field.
This patch cleans it up further by removing the unused field
and assignments.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
There are times when an assigned trigger to a device shouldn't ever
change after intialization.
Examples of this being used is when an provider device has a trigger
that is assigned to an ADC, which uses it populate data into a callback
buffer.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This makes sx9500 driver usable on devicetree based platforms too.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Vlad Dogaru <ddvlad@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver. I have tested with the ADC12138. The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We get 2 warnings when biuld kernel with W=1:
drivers/iio/common/st_sensors/st_sensors_trigger.c:69:13: warning: no previous prototype
for 'st_sensors_irq_handler' [-Wmissing-prototypes]
drivers/iio/common/st_sensors/st_sensors_trigger.c:85:13: warning: no previous prototype
for 'st_sensors_irq_thread' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The ak8974_configure() function is used only from the PM code,
but that can be hidden when CONFIG_PM is disabled:
drivers/iio/magnetometer/ak8974.c:201:12: error: 'ak8974_configure' defined but not used [-Werror=unused-function]
This replaces the #ifdef with a __maybe_unused annotation, which
will work correctly in all configurations and avoid the warning,
as the compiler can now see where ak8974_configure is called from.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7c94a8b2ee8c ("iio: magn: add a driver for AK8974")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
A small rework of the PM code in this driver introduced a harmless
warning when CONFIG_PM_SLEEP is not set:
drivers/iio/common/hid-sensors/hid-sensor-trigger.c:212:12: error: 'hid_sensor_resume' defined but not used [-Werror=unused-function]
This removes the #ifdef and instead marks all three PM functions
as __maybe_unused, which covers all possible cases and is harder
to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7f6cf7414538 ("iio: hid-sensors: use asynchronous resume")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
ads1015_get_channels_config_of()
When terminating for_each_child_of_node() iteration with
break or return, of_node_put() should be used to prevent
stale device node references from being left behind.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fixes the following sparse warnings:
drivers/iio/temperature/maxim_thermocouple.c:35:28: warning:
symbol 'max6675_channels' was not declared. Should it be static?
drivers/iio/temperature/maxim_thermocouple.c:52:28: warning:
symbol 'max31855_channels' was not declared. Should it be static?
drivers/iio/temperature/maxim_thermocouple.c:98:38: warning:
symbol 'maxim_thermocouple_chips' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-By: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
These sensors all have Vdd and Vdd_IO lines. This means the
supplies are *not* optional (optional means that the supply is
optional in the electrical sense, not the software sense)
so we need to get the and enable them at all times.
If the device tree or board file does not define suitable
regulators for the component, it will be substituted by a
dummy regulator, or, if regulators are disabled altogether,
by stubs. There is no need to use the IS_ERR_OR_NULL() check
that is considered harmful.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for Analog Devices AD8801/AD8803, 8 channels 8bits, Digital to
Analog converters.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support the VZ89TE variant which removes the voc_short channel,
and has CRC check for data transactions.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Abstract chip configuration data to allow supporting multiple variants
of the VZ89 chemical sensor line.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.
The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
