| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 6b2e7589b82ff534dd5c6d67dd83c53f13691bec ]
Driver was checking for direct mode but not locking it. Use the
claim/release helper functions to guarantee the device stays in
direct mode during raw reads of proximity data.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Vlad Dogaru <ddvlad@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 80dea21f95a4672cce545f48dc2ca500b69a2584 ]
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw writes.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3bc1abcddb24f55b9c251e03caa4f9bd22ff748b ]
Driver was checking for direct mode before changing oversampling
ratios, but was not locking it. Use the claim/release helper
functions to guarantee the device stays in direct mode while the
oversampling ratios are being updated. Continue to use the drivers
private state lock to protect against conflicting direct mode access
of the state data.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 10e840dfb0b7fc345082dd9e5fff3c1c02e7690e ]
These stand-alone trigger drivers were using iio_trigger_put()
where they should have been using iio_trigger_free(). The
iio_trigger_put() adds a module_put which is bad since they
never did a module_get.
In the sysfs driver, module_get/put's are used as triggers are
added & removed. This extra module_put() occurs on an error path
in the probe routine (probably rare).
In the bfin-timer & interrupt trigger drivers, the module resources
are not explicitly managed, so it's doing a put on something that
was never get'd. It occurs on the probe error path and on the
remove path (not so rare).
Tested with the sysfs trigger driver.
The bfin & interrupt drivers were build tested & inspected only.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be94a6f6d488b4767662e8949dc62361bd1d6311 upstream.
Add missing break in iio_simple_dummy_write_event_config() for the voltage
threshold event enable attribute. Without this writing to the
in_voltage0_thresh_rising_en always returns -EINVAL even though the change
was correctly applied.
Fixes: 3e34e650db197 ("iio: dummy: Demonstrate the usage of new channel types")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca1c39ef76376b67303d01f94fe98bb68bb3861a ]
Reorder error handling labels in order to match the way resources have
been allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0964e40947a630a2a6f724e968246992f97bcf1c upstream.
The driver calls spi_get_drvdata() in its ->remove hook even though it
has never called spi_set_drvdata(). Stack trace for posterity:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
Internal error: Oops: 5 [#1] SMP ARM
[<8072f564>] (mutex_lock) from [<7f1400d0>] (iio_device_unregister+0x24/0x7c [industrialio])
[<7f1400d0>] (iio_device_unregister [industrialio]) from [<7f15e020>] (mcp320x_remove+0x20/0x30 [mcp320x])
[<7f15e020>] (mcp320x_remove [mcp320x]) from [<8055a8cc>] (spi_drv_remove+0x2c/0x44)
[<8055a8cc>] (spi_drv_remove) from [<805087bc>] (__device_release_driver+0x98/0x134)
[<805087bc>] (__device_release_driver) from [<80509180>] (driver_detach+0xdc/0xe0)
[<80509180>] (driver_detach) from [<8050823c>] (bus_remove_driver+0x5c/0xb0)
[<8050823c>] (bus_remove_driver) from [<80509ab0>] (driver_unregister+0x38/0x58)
[<80509ab0>] (driver_unregister) from [<7f15e69c>] (mcp320x_driver_exit+0x14/0x1c [mcp320x])
[<7f15e69c>] (mcp320x_driver_exit [mcp320x]) from [<801a78d0>] (SyS_delete_module+0x184/0x1d0)
[<801a78d0>] (SyS_delete_module) from [<80108100>] (ret_fast_syscall+0x0/0x1c)
Fixes: f5ce4a7a9291 ("iio: adc: add driver for MCP3204/08 12-bit ADC")
Cc: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6f4794371ee7cce1339e7ca9542f1e703c5f84a upstream.
Commit f686a36b4b79 ("iio: adc: mcp320x: Add support for mcp3301")
returns a signed voltage from mcp320x_adc_conversion() but neglects that
the caller interprets a negative return value as failure. Only mcp3301
(and the upcoming mcp3550/1/3) is affected as the other chips are
incapable of measuring negative voltages.
Fix and while at it, add mcp3301 to the list of supported chips at the
top of the file.
Fixes: f686a36b4b79 ("iio: adc: mcp320x: Add support for mcp3301")
Cc: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ee3b7ebcb74714df6d94c8f500f307e1ee5dda5 upstream.
The serial interface can be reset by writing 32 consecutive 1s to the device.
'ret' was initialized correctly but its value was overwritten when
ad7793_check_platform_data() was called. Since a dedicated reset function
is present now, it should be used instead.
Fixes: 2edb769d246e ("iio:ad7793: Add support for the ad7798 and ad7799")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b1f0c31f96c45e8521dd84aae50f2aa4aecfb7b upstream.
The ctrl_reg register needs to be written after any write to
the humidity registers. The value written to the ctrl_reg register
does not necessarily need to change, but a write operation must
occur.
The regmap_update_bits functions will not write to a register
if the register value matches the value to be written. This saves
unnecessary bus operations. The change in this patch forces a bus
write during the chip_config operation by switching to
regmap_write_bits.
This will fix issues where the Humidity Sensor Oversampling bits
are not updated after initialization.
Signed-off-by: Colin Parker <colin.parker@aclima.io>
Acked-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d62c78a6eb9a7d67bace9622b66ad51e81c5f9b upstream.
If an IIO device returns an error code for a read access via debugfs, it
is currently ignored by the IIO core (other than emitting an error
message). Instead, return this error code to user space, so upper layers
can detect it correctly.
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7fc10de8d49a748c476532c9d8e8fe19e548dd67 upstream.
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of 'twl4030_madc_probe()'
commit 7f70be6e4025db0551e6863e7eb9cca07122695c upstream.
Commit 7cc97d77ee8a has introduced a call to 'regulator_disable()' in the
.remove function.
So we should also have such a call in the .probe function in case of
error after a successful 'regulator_enable()' call.
Add a new label for that and use it.
Fixes: 7cc97d77ee8a ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 245a396a9b1a67ac5c3228737c261b3e48708a2a upstream.
If 'devm_regulator_get()' fails, we should go through the existing error
handling path instead of returning directly, as done is all the other
error handling paths in this function.
Fixes: 7cc97d77ee8a ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fa2849e9649b5180ffc4cb3c3b005261c403093a ]
For some reason the axp288_adc driver was modifying the
AXP288_ADC_TS_PIN_CTRL register, changing bits 0-1 depending on
whether the GP_ADC channel or another channel was written.
These bits control when a bias current is send to the TS_PIN, the
GP_ADC has its own pin and a separate bit in another register to
control the bias current.
Not only does changing when to enable the TS_PIN bias current
(always or only when sampling) when reading the GP_ADC make no sense
at all, the code is modifying these bits is writing the entire register,
assuming that all the other bits have their default value.
So if the firmware has configured a different bias-current for either
pin, then that change gets clobbered by the write, likewise if the
firmware has set bit 2 to indicate that the battery has no thermal sensor,
this will get clobbered by the write.
This commit fixes all this, by simply removing all writes to the
AXP288_ADC_TS_PIN_CTRL register, they are not needed to read the
GP_ADC pin, and can actually be harmful.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8f0d7daf53972da0004f7a5a4d938c85333db300 ]
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
$
After this patch:
$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
alias: of:N*T*Cfsl,imx25-gcqC*
alias: of:N*T*Cfsl,imx25-gcq
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4744d4e2afebf9644a439da9ca73d822fdd67bd9 upstream.
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6fe5e52d5ecfc98530034d6c9db73777cf41ede upstream.
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73e3e3fc50de50cfd68e945d85679c983ed31bd9 upstream.
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8245c68350104b6022b6783719e843d69ea7c43 upstream.
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d0e8e795623bd6229cf48bb7777a1c456c370ed upstream.
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0d106b74c558e3000aa0e058b4725cacb70ce77a upstream.
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1664eaacec31035450132c46ed2915fd2b2049a upstream.
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fdd0d32eb95f135041236a6885d9006315aa9a1d upstream.
According to the datasheet, the range of the acceleration is [-10 g, + 10 g],
so the scale factor should be 10 instead of 5.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d466d3c1217406b14b834335b5b4b33c0d45bd09 upstream.
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632fd ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3507e48d3f99a93a3056a34a5365f310434570f upstream.
The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two. The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.
This is going to change userspace ABI. Hopefully fixing this to be
what it should always have been won't break any userspace code.
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e59e18989c68a8d7941005f81ad6abc4ca682de0 upstream.
After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested. This is not consistent and breaks
reading raw values after a suspend-resume.
This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 948588e25b8af5e66962ed3f53e1cae1656fa5af upstream.
Starting from MPU6500, accelerometer dlpf is set in a separate
register named ACCEL_CONFIG_2.
Add this new register in the map and set it for the corresponding
chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ba5b437efaa7a502eec393c045d3bf90c92c4e9 upstream.
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfcea ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6272c0de13abf1480f701d38288f28a11b4301c4 upstream.
According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b211d48abaa0e12e6e6177c0316ff55d11fdfce upstream.
Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.
I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.
Fixes: 217494e5b780 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcbd097 ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce6800 ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5b4da ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9122b54f266ddee09654fe3fbc503c1a60f4a01c upstream.
Using iio_trigger_poll() can oops when multiple interrupts
happen before the first is handled.
Use iio_trigger_poll_chained() instead and use the timestamp
when processed, since it will be in theory be 2 ms max latency.
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 275292d3a3d62670b1b13484707b74e5239b4bb0 upstream.
AS3935 interrupt mask has been incorrect so valid lightning events
would never trigger an buffer event. Also noise interrupt should be
BIT(0).
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cc3bff4efe6164a0c8163331c8aa55454799f42 upstream.
The register mapping for the IIO driver for the Liteon Light and Proximity
sensor LTR501 interrupt mode is interchanged (ALS/PS).
There is a register called INTERRUPT register (address 0x8F)
Bit 0 represents PS measurement trigger.
Bit 1 represents ALS measurement trigger.
This two bit fields are interchanged within the driver.
see datasheet page 24:
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdf
Signed-off-by: Franziska Naepelt <franziska.naepelt@idt.com>
Fixes: 7ac702b3144b6 ("iio: ltr501: Add interrupt support")
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7d86ecf83cb66d3c4c6ac4edb1dd50c0919aa2b upstream.
The third argument of devm_request_threaded_irq() is the primary
handler. It is called in hardirq context and checks whether the
interrupt is relevant to the device. If the primary handler returns
IRQ_WAKE_THREAD, the secondary handler (a.k.a. handler thread) is
scheduled to run in process context.
bcm_iproc_adc.c uses the secondary handler as the primary one
and the other way around. So this patch fixes the same, along with
re-naming the secondary handler and primary handler names properly.
Tested on the BCM9583XX iProc SoC based boards.
Fixes: 4324c97ecedc ("iio: Add driver for Broadcom iproc-static-adc")
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d9854eaea776441b38a9a45b4e6879524c4f48c upstream.
This change undo the change done by 'commit 3bec24747446
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec24747446 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84ca8e364acb26aba3292bc113ca8ed4335380fd upstream.
AS3935_WRITE_DATA macro bit is incorrect and the actual write
sequence is two leading zeros.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed3730c435f1a9f9559ed7762035d22d8a95adfe upstream.
While calculating the compensation of the humidity there are negative values
interpreted as unsigned because of unsigned variables used. These values as
well as the constants need to be casted to signed as indicated by the
documentation of the sensor.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce420fd4251809b4c3119b3b20c8b13bd8eba150 upstream.
realbits, storagebits and shift should be numbers, not ASCII characters.
Signed-off-by: Pavel Roskin <plroskin@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bdc9029685ac03be50b320b29691766d2326c2b upstream.
The gyroscope chip might need to be reset to be used.
Without the chip being reset, the driver stopped at the first
regmap_read (to get the CHIP_ID) and failed to probe.
The datasheet of the gyroscope says that a minimum wait of 30ms after
the reset has to be done.
This patch has been checked on a BMX055 and the datasheet of the BMG160
and the BMI055 give the same reset register and bits.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ff861f59f6c1f5bf2bc03d2cd36ac3f992cbc06 upstream.
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sensor properties losing after resume from S3
commit 3bec247474469f769af41e8c80d3a100dd97dd76 upstream.
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e83bb3e6f3efa21f4a9d883a25d0ecd9dfb431e1 upstream.
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cf6cdba586ced75c69b8314b88b2d2f5ce9b3ed upstream.
Fixes a regression triggered by a change in the layout of
struct iio_chan_spec, but the real bug is in the driver which assumed
a specific structure layout in the first place. Hint: the two bits were
not OR:ed together as implied by the indentation prior to this patch,
there was a comma between them, which accidentally moved the ..._SCALE
bit to the next structure field. That field was .info_mask_shared_by_type
before the _available attributes was added by commit 51239600074b
("iio:core: add a callback to allow drivers to provide _available
attributes") and .info_mask_separate_available afterwards, and the
regression happened.
info_mask_shared_by_type is actually a better choice than the originally
intended info_mask_separate for the ..._SCALE bit since a constant is
returned from mpl3115_read_raw for the scale. Using
info_mask_shared_by_type also preserves the behavior from before the
regression and is therefore less likely to cause other interesting side
effects.
The above mentioned regression causes an unintended sysfs attibute to
show up that is not backed by code, in turn causing the following NULL
pointer defererence to happen on access.
Segmentation fault
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ecc3c000
[00000000] *pgd=87f91831
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1051 Comm: cat Not tainted 4.10.0-rc5-00009-gffd8858-dirty #3
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: ed54ec00 task.stack: ee2bc000
PC is at 0x0
LR is at iio_read_channel_info_avail+0x40/0x280
pc : [<00000000>] lr : [<c06fbc1c>] psr: a0070013
sp : ee2bdda8 ip : 00000000 fp : ee2bddf4
r10: c0a53c74 r9 : ed79f000 r8 : ee8d1018
r7 : 00001000 r6 : 00000fff r5 : ee8b9a00 r4 : ed79f000
r3 : ee2bddc4 r2 : ee2bddbc r1 : c0a86dcc r0 : ee8d1000
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 3cc3c04a DAC: 00000051
Process cat (pid: 1051, stack limit = 0xee2bc210)
Stack: (0xee2bdda8 to 0xee2be000)
dda0: ee2bddc0 00000002 c016d720 c016d394 ed54ec00 00000000
ddc0: 60070013 ed413780 00000001 edffd480 ee8b9a00 00000fff 00001000 ee8d1018
dde0: ed79f000 c0a53c74 ee2bde0c ee2bddf8 c0513c58 c06fbbe8 edffd480 edffd540
de00: ee2bde3c ee2bde10 c0293474 c0513c40 c02933e4 ee2bde60 00000001 ed413780
de20: 00000001 ed413780 00000000 edffd480 ee2bde4c ee2bde40 c0291d00 c02933f0
de40: ee2bde9c ee2bde50 c024679c c0291ce0 edffd4b0 b6e37000 00020000 ee2bdf78
de60: 00000000 00000000 ed54ec00 ed013200 00000817 c0a111fc edffd540 ed413780
de80: b6e37000 00020000 00020000 ee2bdf78 ee2bded4 ee2bdea0 c0292890 c0246604
dea0: c0117940 c016ba50 00000025 c0a111fc b6e37000 ed413780 ee2bdf78 00020000
dec0: ee2bc000 b6e37000 ee2bdf44 ee2bded8 c021d158 c0292770 c0117764 b6e36004
dee0: c0f0d7c4 ee2bdfb0 b6f89228 00021008 ee2bdfac ee2bdf00 c0101374 c0117770
df00: 00000000 00000000 ee2bc000 00000000 ee2bdf34 ee2bdf20 c016ba04 c0171080
df20: 00000000 00020000 ed413780 b6e37000 00000000 ee2bdf78 ee2bdf74 ee2bdf48
df40: c021e7a0 c021d130 c023e300 c023e280 ee2bdf74 00000000 00000000 ed413780
df60: ed413780 00020000 ee2bdfa4 ee2bdf78 c021e870 c021e71c 00000000 00000000
df80: 00020000 00020000 b6e37000 00000003 c0108084 00000000 00000000 ee2bdfa8
dfa0: c0107ee0 c021e838 00020000 00020000 00000003 b6e37000 00020000 0001a2b4
dfc0: 00020000 00020000 b6e37000 00000003 7fffe000 00000000 00000000 00020000
dfe0: 00000000 be98eb4c 0000c740 b6f1985c 60070010 00000003 00000000 00000000
Backtrace:
[<c06fbbdc>] (iio_read_channel_info_avail) from [<c0513c58>] (dev_attr_show+0x24/0x50)
r10:c0a53c74 r9:ed79f000 r8:ee8d1018 r7:00001000 r6:00000fff r5:ee8b9a00
r4:edffd480
[<c0513c34>] (dev_attr_show) from [<c0293474>] (sysfs_kf_seq_show+0x90/0x110)
r5:edffd540 r4:edffd480
[<c02933e4>] (sysfs_kf_seq_show) from [<c0291d00>] (kernfs_seq_show+0x2c/0x30)
r10:edffd480 r9:00000000 r8:ed413780 r7:00000001 r6:ed413780 r5:00000001
r4:ee2bde60 r3:c02933e4
[<c0291cd4>] (kernfs_seq_show) from [<c024679c>] (seq_read+0x1a4/0x4e0)
[<c02465f8>] (seq_read) from [<c0292890>] (kernfs_fop_read+0x12c/0x1cc)
r10:ee2bdf78 r9:00020000 r8:00020000 r7:b6e37000 r6:ed413780 r5:edffd540
r4:c0a111fc
[<c0292764>] (kernfs_fop_read) from [<c021d158>] (__vfs_read+0x34/0x118)
r10:b6e37000 r9:ee2bc000 r8:00020000 r7:ee2bdf78 r6:ed413780 r5:b6e37000
r4:c0a111fc
[<c021d124>] (__vfs_read) from [<c021e7a0>] (vfs_read+0x90/0x11c)
r8:ee2bdf78 r7:00000000 r6:b6e37000 r5:ed413780 r4:00020000
[<c021e710>] (vfs_read) from [<c021e870>] (SyS_read+0x44/0x90)
r8:00020000 r7:ed413780 r6:ed413780 r5:00000000 r4:00000000
[<c021e82c>] (SyS_read) from [<c0107ee0>] (ret_fast_syscall+0x0/0x1c)
r10:00000000 r8:c0108084 r7:00000003 r6:b6e37000 r5:00020000 r4:00020000
Code: bad PC value
---[ end trace 9c4938ccd0389004 ]---
Fixes: cc26ad455f57 ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver")
Fixes: 51239600074b ("iio:core: add a callback to allow drivers to provide _available attributes")
Reported-by: Ken Lin <ken.lin@advantech.com>
Tested-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a6e1d56a0769795a36c0461c64bf5e5b9bbb4c0 upstream.
Fixes a regression triggered by a change in the layout of
struct iio_chan_spec, but the real bug is in the driver which assumed
a specific structure layout in the first place. Hint: the three bits were
not OR:ed together as implied by the indentation prior to this patch,
there was a comma between the first two, which accidentally moved the
..._SCALE and ..._OFFSET bits to the next structure field. That field
was .info_mask_shared_by_type before the _available attributes was added
by commit 51239600074b ("iio:core: add a callback to allow drivers to
provide _available attributes") and .info_mask_separate_available
afterwards, and the regression happened.
info_mask_shared_by_type is actually a better choice than the originally
intended info_mask_separate for the ..._SCALE and ..._OFFSET bits since
a constant is returned from mpl115_read_raw for the scale/offset. Using
info_mask_shared_by_type also preserves the behavior from before the
regression and is therefore less likely to cause other interesting side
effects.
The above mentioned regression causes unintended sysfs attibutes to
show up that are not backed by code, in turn causing a NULL pointer
defererence to happen on access.
Fixes: 3017d90e8931 ("iio: Add Freescale MPL115A2 pressure / temperature sensor driver")
Fixes: 51239600074b ("iio:core: add a callback to allow drivers to provide _available attributes")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 828f84ee8f84710ea1818b3565add268bcb824c8 upstream.
FIFO was being read every sample after the "almost full" state was
reached. This was due to an incorrect placement of the parenthesis
in the while condition check.
Note - the fixes tag is not actually correct, but the fix in this patch
would also be needed for it to function correctly so we'll go with that
one. Backports should pick up both.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Fixes: b74fccad7 ("iio: health: max30100: correct FIFO check condition")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c113b5e0082e90d2e1c7b12e96a7b8cf0623e27 upstream.
The DHT22 (AM2302) datasheet specifies that the LOW start pulse should not
exceed 20ms. However, observations with an oscilloscope of an RPi Model 2B
(rev 1.1) communicating with a DHT22 sensor showed that the driver was
consistently sending start pulses longer than 20ms:
Kernel 4.7.10-v7+ (n=132):
Minimum pulse length: 20.20ms
Maximum: 29.84ms
Mean: 24.96ms
StDev: 2.82ms
Sensor response rate: 100%
Read success rate: 76%
On kernel 4.8, the start pulse was so long that the sensor would not even
respond 97% of the time:
Kernel 4.8.16-v7+ (n=100):
Minimum pulse length: 30.4ms
Maximum: 74.4ms
Mean: 39.3ms
StDev: 10.2ms
Sensor response rate: 3%
Read success rate: 3%
The driver would return ETIMEDOUT and write log messages like this:
[ 51.430987] dht11 dht11@0: Only 1 signal edges detected
[ 66.311019] dht11 dht11@0: Only 0 signal edges detected
Replacing msleep(18) with usleep_range(18000, 20000) made the pulse length
sane again and restored responsiveness:
Kernel 4.8.16-v7+ with usleep_range (n=123):
Minimum pulse length: 18.16ms
Maximum: 20.20ms
Mean: 19.85ms
StDev: 0.51ms
Sensor response rate: 100%
Read success rate: 84%
Signed-off-by: John Brooks <john@fastquake.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5badd1e97e6caeca78ad74191f12fc923c403a8 upstream.
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Replace it with spi
functions to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 802ecfc113df1e15af1d028427cbbe785ae9cc4a upstream.
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Replace it with i2c
functions to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1aaf20ee655888c227d5137b7a63551f8d15416 upstream.
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Use dev_get_drvdata()
for a platform device to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
