| Age | Commit message (Collapse) | Author |
|---|
|
The OMAP IOMMU driver was originally designed as modules, and split
into a core module and a thin arch-specific module through the OMAP
arch-specific struct iommu_functions, to scale for both OMAP1 and
OMAP2+ IOMMU variants. The driver can only be built for OMAP2+
platforms currently, and also can only be built-in after the
adaptation to generic IOMMU API. The OMAP1 variant was never added
and will most probably be never added (the code for the only potential
user, its parent, DSP processor has already been cleaned up). So,
consolidate the OMAP2 specific omap-iommu2 module into the core OMAP
IOMMU driver - this eliminates the arch-specific ops structure and
simplifies the driver into a single module that only implements the
generic IOMMU API's iommu_ops.
The following are the main changes:
- omap-iommu2 module is completely eliminated, with the common
definitions moved to the internal omap-iommu.h, and the ops
implementations moved into omap-iommu.c
- OMAP arch-specific struct iommu_functions is also eliminated,
with the ops implementations directly absorbed into the calling
functions
- iotlb_alloc_cr() is no longer inlined and defined only when
PREFETCH_IOTLB is defined
- iotlb_dump_cr() is similarly defined only when CONFIG_OMAP_IOMMU_DEBUG
is defined
- Elimination of the OMAP IOMMU exported functions to register the
arch ops, omap_install_iommu_arch() & omap_uninstall_iommu_arch()
- Any stale comments about OMAP1 are also cleaned up
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The function omap2_iommu_fault_isr() does an unnecessary
recomputation of the return value. The logic relies on
setting the same bit fields as the MMU fault error status
bits, so simplify this function and remove the unneeded
macros. These macros were originally exported to notify
MMU faults to users prior to the IOMMU framework adaptation,
but are now redundant.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The omap2_iommu_save_ctx() and omap2_iommu_restore_ctx()
performs a sanity version check against a fixed value
that is correct only for OMAP2/OMAP3 IOMMUs. This fixed check
does not scale for all OMAP2+ IOMMUs and is not absolutely
required, so it has been removed.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The function omap_iommu_arch_version() is not used anymore,
and is not required either, so remove it. The .version field
in struct iommu_functions that this function uses is also
removed, as it is not really an ops to retrieve a version and
there won't be any usage for this field either.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The remoteproc MMUs in OMAP4+ SoCs have some additional debug
registers that can give out the PC value in addition to the
MMU fault address. The PC value can be extracted properly only
on the DSP cores, and is not available on the ARM processors
within the IPU sub-systems. Instead, the MMUs have been enhanced
to throw a bus-error response back to the IPU processors.
This functionality is programmable through the MMU_GP_REG register.
The cores are simply stalled if the MMU_GP_REG.BUS_ERR_BACK_EN bit
is not set. When set, a bus-error exception is raised allowing the
processor to handle it as a bus fault and provide additional debug
information. This feature is turned on by default by the driver on
iommus supporting it.
Signed-off-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
Use runtime PM functionality interfaced with hwmod enable/idle
functions, to replace direct clock operations and sysconfig
handling.
Due to reset sequence, pm_runtime_[get|put]_sync must be used, to
avoid possible operations with the module under reset. Because of
this and given that the driver uses spin_locks to protect their
critical sections, we must use pm_runtime_irq_safe in order for the
runtime ops to be happy, otherwise might_sleep_if checks in runtime
framework will complain.
The remaining pm_runtime out of iommu_enable and iommu_disable
corresponds to paths that can be accessed through debugfs, some of
them doesn't work if the module is not enabled first, but in future
if the mmu is idled withouth freeing, these are needed to debug.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
Use hwmod data and device attributes to build and register an
omap device for iommu driver.
- Update the naming convention in isp module.
- Remove unneeded check for number of resources, as this is now
handled by omap_device and prevents driver from loading.
- Now unused, remove platform device and resource data, handling
of sysconfig register for softreset purposes, use default
latency structure.
- Use hwmod API for reset handling.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move some of the definitions in omap-iommu.h that can be made local to
either drivers/iommu.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
[tony@atomide.com: updated for header changes in the series]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This file should not be in arch/arm. Move it to drivers/iommu
to allow making most of the header local to drivers/iommu.
This is needed as we are removing plat and mach includes
from drivers for ARM common zImage support.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
