| Age | Commit message (Collapse) | Author |
|---|
|
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
When "re-add" is writted to /sys/block/mdXX/md/dev-YYY/state,
the clustered md:
1. Sends RE_ADD message with the desc_nr. Nodes receiving the message
clear the Faulty bit in their respective rdev->flags.
2. The node initiating re-add, gathers the bitmaps of all nodes
and copies them into the local bitmap. It does not clear the bitmap
from which it is copying.
3. Initiating node schedules a md recovery to sync the devices.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This adds "remove" capabilities for the clustered environment.
When a user initiates removal of a device from the array, a
REMOVE message with disk number in the array is sent to all
the nodes which kick the respective device in their own array.
This facilitates the removal of failed devices.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
A --cluster-confirm without an --add (by another node) can
crash the kernel.
Fix it by guarding it using a state.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Algorithm:
1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues
ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD)
2. Node 1 sends NEWDISK with uuid and slot number
3. Other nodes issue kobject_uevent_env with uuid and slot number
(Steps 4,5 could be a udev rule)
4. In userspace, the node searches for the disk, perhaps
using blkid -t SUB_UUID=""
5. Other nodes issue either of the following depending on whether the disk
was found:
ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and
disc.number set to slot number)
ioctl(CLUSTERED_DISK_NACK)
6. Other nodes drop lock on no-new-devs (CR) if device is found
7. Node 1 attempts EX lock on no-new-devs
8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk
as SpareLocal
9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED
10. Other nodes understand if the device is added or not by reading the superblock again after receiving the METADATA_UPDATED message.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
|
If there is a resync going on, all nodes must suspend writes to the
range. This is recorded in the suspend_info/suspend_list.
If there is an I/O within the ranges of any of the suspend_info,
should_suspend will return 1.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
|
When a resync is initiated, RESYNCING message is sent to all active
nodes with the range (lo,hi). When the resync is over, a RESYNCING
message is sent with (0,0). A high sector value of zero indicates
that the resync is over.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
|
- request to send a message
- make changes to superblock
- send messages telling everyone that the superblock has changed
- other nodes all read the superblock
- other nodes all ack the messages
- updating node release the "I'm sending a message" resource.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
|
When a node joins, it does not know of other nodes performing resync.
So, each node keeps the resync information in it's LVB. When a new
node joins, it reads the LVB of each "online" bitmap.
[TODO] The new node attempts to get the PW lock on other bitmap, if
it is successful, it reads the bitmap and performs the resync (if
required) on it's behalf.
If the node does not get the PW, it requests CR and reads the LVB
for the resync information.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
|
DLM offers callbacks when a node fails and the lock remastery
is performed:
1. recover_prep: called when DLM discovers a node is down
2. recover_slot: called when DLM identifies the node and recovery
can start
3. recover_done: called when all nodes have completed recover_slot
recover_slot() and recover_done() are also called when the node joins
initially in order to inform the node with its slot number. These slot
numbers start from one, so we deduct one to make it start with zero
which the cluster-md code uses.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
|
This allows dynamic registering of cluster hooks.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
|
