Age | Commit message (Collapse) | Author |
|
This patch adds V4L2 controls for Auto Exposure Control and Auto Gain
Control settings. These settings include low pass filter, update
frequency of these settings and the update interval for those units.
[Avoid forward declarations]
[Fix 80 columns limit violation]
[Rename controls to avoid underscores in names]
[Fix the AEC maximum shutter width on MT9V032]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The power_on function of the driver resets the chip and sets the
CHIP_CONTROL register to 0. This switches the operating mode to slave.
The s_stream function sets the correct mode. But this caused problems on
a board where the camera chip is operated as master. The camera started
after a random amount of time streaming an image, I observed between 10
and 300 seconds.
The STRFM_OUT and STLN_OUT pins are not connected on this board which
may cause some issues in slave mode. I could not find any documentation
about this.
Keeping the chip in master mode after the reset helped to fix this
issue for me.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
functionality
Since commit b42261078a91 ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The of_gpio.h header isn't needed, don't include it.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().
The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
These v4l2_ctrl_ops structures are never modified, like all the other
v4l2_ctrl_ops structures, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
drivers/media/i2c/mt9v032.c: In function ‘mt9v032_probe’:
CC [M] drivers/media/i2c/s5k4ecgx.o
drivers/media/i2c/mt9v032.c:996:20: warning: ‘pdata’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (pdata && pdata->link_freqs) {
^
It can indeed be uninitialized in one corner case. Initialize to NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Parse DT properties into a platform data structure when a DT node is
available.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The device requires control to be properly operated, they're not
optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
These drivers are moved to support asynchronous probing,
v4l2_async_unregister_subdev() unregisters the subdev so
there isn't a need to explicitly call v4l2_device_unregister_subdev().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Replace all references to the old definitions in i2c drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This switches all register accesses to use regmap. It allows to
use the regmap cache, tracing, and debug register dump facilities,
and removes the need to open code read-modify-writes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add support for registering the sensor subdevice using the v4l2-async API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
as are mt9v024 and mt9v034. With minimal changes it is possible
to support mt9v02[24] with the same driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The read mode register bits 8 and 9 are set and marked as reserved.
Don't clear them.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.
Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
clk_set_rate(), clk_prepare_enable() functions can fail, so check the return
values to avoid surprises.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The MT9V034 sensor is very similar to the MT9V032, with a couple of
different registers and parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
To prepare support of the MT9V034, add the necessary infrastructure to
support model-specific parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Identify the model based on the I2C device name and configure formats
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The sensor can scale the image down using binning by 1, 2 or 4 in both
directions. Update size enumeration and ratio and binning factor
computation accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The active pixel array size is 753x481 with 4 additional black rows at
the top. Fix the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The EXT_CLK macro is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Configure the device external clock using the common clock framework
instead of a board code callback function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The control handler must be freed in the probe error path and in the
remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
pattern control
V4L2_CID_TEST_PATTERN is now a standard control.
This patch replaces the user defined control for test
pattern to make use of standard control V4L2_CID_TEST_PATTERN.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Provide pixel rate control calculated from external clock and horizontal
binning factor.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Move ancillary I2C drivers into drivers/media/i2c, in order to
better organize them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|