| Age | Commit message (Collapse) | Author |
|---|
|
Very similar to TPS65920
List of differences: http://www.ti.com/litv/pdf/swcu066b
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Purely for defensiveness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The tps65910_irq_exit() cleanup function was generating a warning from
sparse due to the lack of a prototype. This wasn't causing GCC warnings
as the driver wasn't cleaning up its IRQs on exit at all so there was no
use of an unprototyped function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Tunnel Creek has an additional watchdog core.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This synchronize the subdevice entries for the AB8500 MFD driver
with the latest development of subdrivers for things like battery
charging and temperature monitoring.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Internal MFD device structs are marked as __devinitdata since the kernel
will allocate memory for the same when calling mfd_add_devices.
Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Reviewed-by: Johan Palsson <johan.palsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This module controls the interrupt handling for the tps65912.
The interrupt sources can be the following:
- GPIO
- PWRON signal
- PWRHOLD signal
- Temperature detection
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The tps65912 chip is a power management IC. It contains the following
components:
- Regulators
- GPIO controller
The core driver is registered as a platform driver, it provides communication
through I2C and SPI interfaces.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the generic irq chip framework for implementing the irq chip for
the jz4740-adc driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Even if we would've BUG()ed we should still tidy up after ourselves if that
isn't enabled in the kernel config.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When the byte swap was factored out into the per-register I/O functions
the register restore for the IRQ mask cache (which we use and store in
CPU native format for the interrupt handler) was not updated to do a byte
swap when it uses the bulk I/O. Fix this by writing the cache out one
register at a time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x AUXADC hardware can schedule multiple conversions at once,
allowing higher performance when more than one source is in use as we
can have the hardware start new conversions without having to wait for
a register write.
Take advantage of this in the interrupt driven case, maintaining a list of
callers that are waiting for AUXADC conversions and completing them all
simultaneously. The external interface of the AUXADC is not changed so
there will be limited use of the feature immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Switch on the device type before revision since anything we do here will
be device as well as revision specific.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This allows boards to leave the irq_base field unitialized and
prevents them having to reserve irqs in the platform.
pdata can be optional for irq support now. Without pdata the
driver allocates some free irq range. With pdata and irq_base > 0
the driver allocates exactly the specified irq.
Without pdata the irq defaults to IRQF_TRIGGER_LOW.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In preparation for some additional work on the wm831x AUXADC code move the
support into a separate file. This is a simple code motion patch, there
should be no functional changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Ensure that there's no possibility of loosing an AUXADC interrupt by reading
the conversion result in the IRQ handler when using interrupts. Otherwise
it's possible that under very heavy load a new conversion could be initiated
before the acknowledgement for a previous interrupt has happened.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use irq_allocate_desc() to get the IRQ range, which turns into a noop on
non-sparse systems. Since all existing users are non-sparse there should
be no compatibility issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The RTC uses the 32.768kHz crystal so if it's not enabled (and it can only
be enabled via OTP or InstantConfig, not runtime software) the RTC can't
function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow platform data to flag the touchscreen as disabled so that if the
touch driver is built in we don't end up causing lots of work by spuriously
detecting touchscreen activity on systems where it isn't in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Systems using this functionality will be uncommon.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x IRQ set_type() operation is doing a direct register write when
called but since set_type() is called with the bus lock held this isn't
legal and could cause deadlocks in the IRQ core.
Fix this by posting the updates into an array and syncing in the
bus_sync_unlock() callback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
* git://git.infradead.org/battery-2.6:
gpio-charger: Fix checking return value of request_any_context_irq
power_supply: MAX17042: Support additional properties
max8903_charger: Allow platform data to be __initdata
power_supply: Add charger driver for MAX8998/LP3974
power_supply: Add charger driver for MAX8997/8966
max17042_battery: Remove obsolete cleanup for clientdata
twl4030_charger: Fix warnings
wm831x_power: Support multiple instances
wm831x_backup: Support multiple instances
apm_power: Fix style error in macros
s3c_adc_battery: Fix annotation for s3c_adc_battery_probe()
bq20z75: Enable detection after registering
bq20z75: Add support for external notification
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
|
|
This patch simplifies the platform data slightly, by removing
unused elements.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
|
|
Sync with Linus' tree to be able to apply pending patches that
are based on newer code already present upstream.
|
|
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch supports power supply APIs for MAX8998/LP3974.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
There is no need to have two different types for
tracking the selected PLL.
Use only the defines, when dealing with the PLLs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Remove the twl6040_request_irq/free_irq inline functions,
and use direct calls instead in the core driver to
register the threaded irq.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to operate correctly twl6040 needs correct
interrupt configuration.
The slave drivers (vibra, and ASoC codec) will refuse
to probe, if the interrupt configuration is not correct.
In this way some checks can be removed from the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Provide the irq number for slaves via resource on the
platform device.
The irq number configuration is done in the twl6040-core
at probe time, so machine drivers do not need to be
modified.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Base on Mark's comment [1], I make the Kconfig entry invisible to users.
[1] https://lkml.org/lkml/2011/5/14/136
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Fix below build error:
CC drivers/mfd/tps65911-comparator.o
drivers/mfd/tps65911-comparator.c: In function 'tps65911_comparator_probe':
drivers/mfd/tps65911-comparator.c:131: error: 'struct tps65910_platform_data' has no member named 'vmbch_threshold'
drivers/mfd/tps65911-comparator.c:137: error: 'struct tps65910_platform_data' has no member named 'vmbch2_threshold'
make[2]: *** [drivers/mfd/tps65911-comparator.o] Error 1
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This reverts commit 7e6502d577106fb5b202bbaac64c5f1b065e6daa.
Oops are produced during initialization of ehci and ohci
drivers. This is because the run time pm apis are used by
the driver but the corresponding hwmod structures and
initialization is not merged. hence revering back the
commit id 7e6502d577106fb5b202bbaac64c5f1b065e6daa
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reported-by: Luciano Coelho <coelho@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Pass twl4030_codec_data instead of the twl4030_audio_data
for the ASoC codec driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
TWL6040 IC provides analog high-end audio codec functions for
handset applications. It contains several audio analog inputs
and outputs as well as vibrator support. It's connected to the
host processor via PDM interface for audio data communication.
The audio modules are controlled by internal registers that
can be accessed by I2C and PDM interface.
TWL6040 MFD will be registered as a child of TWL-CORE, and will
have two children of its own: twl6040-codec and twl6040-vibra.
This driver is based on TWL4030 and WM8350 MFD drivers.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In preparation of renaming the driver from twl4030-codec
to twl4030-audio, first do some clean ups in the driver,
which does not cause any problems outside.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Liam Girdwood <lrg@ti.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This driver adds functionality to the tps65911 chip driver.
Two of the comparators are configurable by software and measures
VCCS voltage to detect high or low voltage scenarios.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
TPS65911 adds new interrupt sources, as well as two new registers
to handle them, one for interrupt status and one for interrupt
masking. The added irqs are:
-VMBCH2 - Low and High threshold
-GPIO1-8 - Rising and falling edge detection
-WTCHDG - Watchdog interrupt
-PWRDN - PWRDN reset interrupt
The code should handle these new registers only when the chip
version is TPS65911.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
The TPS65911 is the next generation of the TPS65910 family of
PMIC chips. It adds a few features:
- Watchdog Timer
- PWM & LED generators
- Comparators for system control status
It also adds a set of Interrupts and GPIOs, among other things.
The driver exports a function to identify between different
versions of the tps65910 family, allowing other modules to
identify the capabilities of the current chip.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
If bytes == (TPS65910_MAX_REGISTER + 1), we have a buffer overflow when
doing memcpy(&msg[1], src, bytes).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
