Age | Commit message (Collapse) | Author |
|
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
replace au_read/write/sync with __raw_read/write and wmb.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7465/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The NAND command helpers tend to automatically shift the column address
for x16 bus devices, since most commands expect a word address, not a
byte address. The Read ID command, however, expects an 8-bit address
(i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
0x20).
This fixes the column address for a few drivers which imitate the
nand_base defaults. Note that I don't touch sh_flctl.c, since it already
handles this problem slightly differently (note its comment "READID is
always performed using an 8-bit bus").
I have not tested this patch, as I only have x8 parts up for testing at
this point. Hopefully that can change soon...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Brian: dropped one incorrect hunk]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add missing platform_set_drvdata() in au1550nd_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Transform the au1550nd.c driver into a platform_driver and hook it
up in the PB1550 board (gen_nand works fine on the DB1550, but since
I don't have a PB1550 to test this driver stays for now).
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mtd@lists.infradead.org
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2875/
Patchwork: https://patchwork.linux-mips.org/patch/3160/
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
|
|
No longer required
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/include/asm/mach-au1x00/au1xxx.h
|
|
Therefor -> Therefore
[Intern], [Internal] -> [INTERN]
[REPLACABLE] -> [REPLACEABLE]
syndrom, syndom -> syndrome
ecc -> ECC
buswith -> buswidth
endianess -> endianness
dont -> don't
occures -> occurs
independend -> independent
wihin -> within
erease -> erase
blockes -> blocks
...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
|
|
The older add_mtd_device()/add_mtd_partitions() and their removal
counterparts will soon be gone. Replace uses with mtd_device_register()
and mtd_device_unregister().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6f359df4f45152f2b40e1d4d1891392
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/mtd/nand/sh_flctl.c
Maxim's patch to initialise sysfs attributes depends on the patch which
actually adds sysfs_attr_init().
|
|
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove unnecessary casts for p_nand, it is already a void __iomem *.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Use kzalloc() instead of kmalloc()/memset().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove unused variable from au1550 NAND driver.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The previous change of the command / hardware control allows to
remove the write_byte/word functions completely, as their only
user were nand_command and nand_command_lp.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The hwcontrol function enforced a step by step state machine
for any kind of hardware chip access. Let the hardware driver
know which control bits are set and inform it about a change
of the control lines. Let the hardware driver write out the
command and address bytes directly. This gives a peformance
advantage for address bus controlled chips and simplifies the
quirks in the hardware drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
First step of modularizing ECC support.
- Move ECC related functionality into a seperate embedded data structure
- Get rid of the hardware dependend constants to simplify new ECC models
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
At least two flashes exists that have the concept of a minimum write unit,
similar to NAND pages, but no other NAND characteristics. Therefore, rename
the minimum write unit to "writesize" for all flashes, including NAND.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
|
|
On AMD Au1550 the static bus controller fails to keep -CE asserted during
chip ready delay on read commands and the NAND chip being used requires this.
So, the current driver allows nand_base.c to drive -CE manually during the
entire sector read. When the PCMCIA driver is enabled however, occasionally
the ECC errors occur on NAND reads. This happens because the PCMCIA driver
polls sockets periodically and reads one of the board's control/status regs
(BCSRs) which are on the same static bus as the NAND flash, and just use
another chip select (and the NOR flash also resides on that bus), so as the
NAND driver forces NAND chip select asserted and the -RE signal is shared, a
contention occurs on the static bus when BCSR or NOR flash is read while we're
reading from NAND.
So, we either can't keep interrupts enabled during the whole NAND sector
read (which is hardly acceptable), or have to implement some interlocking
scheme between multiple drivers (which is painful, and makes me shudder :-).
There's a third way which has proven to work: to force -CE asserted only
while we're waiting for a NAND chip to become ready after a read command,
disabling interrupts for a maximum of 25 microseconds (according to Toshiba
TC58DVM92A1FT00 datasheet -- this chip is mentioned in the board schematics);
for Samsung NAND chip which seems to be actually used this delay is even less,
12 us.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
During the last cleanup of the AMD Au1550 NAND driver the old buglet was
reintroduced: as the MEM_STNDCTL register is write-only and seem to always
read as 0x31, read-modify-write to it done in au1xxx_nand_init() will have the
side effect of enabling -RCS0/1 pin override (via bits 4/5 of this reg.), thus
possibly causing a contention on the static bus when the NOR flash (using
-RCS0) or board control status registers (using -RCS2) are read. Luckily, this
goes away with a first NAND access, since au1550_hwcontrol() doesn't try to
read this register before writing anymore.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The _board_ driver needs to be mtd->owner, and it in turn pins the
nand.ko module. Fix them all to actually do that, and fix nand.ko not to
overwrite it -- and also to check that the caller sets it, if the caller
is a module.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
It was just too painful to deal with.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
- cleaned up the partitions and include files
- added more flexible CS and address detection and setup
Regression tested on db1200 and db1550.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|