| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Xiaobo Xie <xiaobo.xie@nxp.com>
|
|
[ Upstream commit 19649e2c16fbc94b664f7074ec4fa9f15292fdce ]
wait_for_completion_timeout() returns 0 if a timeout occurred, 1
otherwise. Fix the sunxi_nfc_wait_events() accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Bufnum mask is used to calculate page position in the internal SRAM.
As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
versions which had 8KB. Hence bufnum mask needs to be updated.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
All IFC version >= 1.0 use 28nm technology for SRAM. Here SRAM has
a requirement to initialize before any read operation performed for
avoiding ECC Error.
So update condition check to initialize SRAM for all IFC version >=
1.0.0.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
commit 10777de570016471fd929869c7830a7772893e39 upstream.
The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which
0x1 : BCH_DISABLED
0x0 : BCH_ENABLED
But currently host->bch_enabled is being assigned to BCH_DISABLED.
Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8a9b320a26c1ea28e51e4f3ecfb593d5aac2910 upstream.
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bff08dffe3115a25ce04b95ea75f6d868572c60 upstream.
Commit a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7f8c1756e9a5f1258a7cc6b663f8451b724900f upstream.
When using soft ecc, if no ooblayout is given, the core automatically
uses one of the nand_ooblayout_{sp,lp}*() functions to determine the
layout inside the out of band data.
Until kernel version 4.6, struct nand_ecclayout was used for that
purpose. During the migration from 4.6 to 4.7, an error shown up in the
small page layout, in the case oob section is only 8 bytes long.
The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4)
as free bytes, one byte (5) for bad block marker and finally
two bytes (6, 7) as free bytes, as shown there:
[linux-4.6] drivers/mtd/nand/nand_base.c:52
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.eccpos = {0, 1, 2},
.oobfree = {
{.offset = 3,
.length = 2},
{.offset = 6,
.length = 2} }
};
This fixes the current implementation which is incoherent. It
references bit 3 at the same time as an ecc byte and a free byte.
Furthermore, it is clear with the previous implementation that there
is only one ecc section with 8 bytes oob sections. We shall return
-ERANGE in the nand_ooblayout_ecc_sp() function when asked for the
second section.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a11bf5ed951f8900d244d09eb03a888b59c7fc82 upstream.
Some ONFI NANDs do not support the SET/GET FEATURES commands, which,
according to the spec, is perfectly valid.
On these NANDs we can't set a specific timing mode using the "timing
mode" feature, and we should assume the NAND does not require any setup
to enter a specific timing mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reported-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As NAND support for Freescale/NXP IFC controller is available on
LS1021A, the dependency for LS1021A is added.
LS1021A is an earlier product and is not compatible with later
LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
commit 9d2ee0a60b8bd9bef2a0082c533736d6a7b39873 upstream.
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a623e07694437ad09f382a13f76cffc32239a7f upstream.
The old 1-bit hamming layout requires ECC data to be placed at a
fixed offset, and not necessarily at the end of the OOB area.
Add this old layout back in order to fix legacy setups.
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d283ede59869159f4bb84ae689258c5caffce54 upstream.
commit c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 675b11d94ce9baa5eb365a51b35d2793f77c8ab8 upstream.
The clk handling in orion_nand.c had two problems:
- In the probe function, clk_put() was called for an enabled clock,
which violates the API (see documentation for clk_put() in
include/linux/clk.h)
- In the error path of the probe function, clk_put() could be called
twice for the same clock.
In order to clean this up, use the managed function devm_clk_get() and
store the pointer to the clk in the driver data.
Fixes: baffab28b13120694fa3ebab08d3e99667a851d2 ('ARM: Orion: fix driver probe error handling with respect to clk')
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 656441478ed55d960df5f3ccdf5a0f8c61dfd0b3 upstream.
The commit 7a654172161c ("mtd/ifc: Add support for IFC controller
version 2.0") added support for version 2.0 of the IFC controller.
The version 2.0 controller has the ECC status registers at a different
location to the previous versions.
Correct the fsl_ifc_nand structure so that the ECC status can be read
from the correct location for both version 1.0 and 2.0 of the controller.
Fixes: 7a654172161c ("mtd/ifc: Add support for IFC controller version 2.0")
Signed-off-by: Mark Marshall <mark.marshall@omicronenergy.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2724663494f7313f53da10d8c0a729c5e3c4dea upstream.
Remove the usage of modules functions to make this driver compile
again. Otherwise an include of linux/modules.h would be needed.
Fixes: 024366750c2e ("mtd: nand: xway: convert to normal platform driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73529c872a189c747bdb528ce9b85b67b0e28dec upstream.
The xway_nand driver accesses the ltq_ebu_membase symbol which is not
exported. This also should not get exported and we should handle the
EBU interface in a better way later. This quick fix just deactivated
support for building as module.
Fixes: 99f2b107924c ("mtd: lantiq: Add NAND support on Lantiq XWAY SoC.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf9e1672a66c49ed8903c01b4c380a2f2dc91b40 upstream.
Semantics of NR_IRQS is different on machines with SPARSE_IRQ option
disabled or enabled, in the latter case IRQs are allocated starting
at least from the value specified by NR_IRQS and going upwards, so
the check of (irq >= NR_IRQ) to decide about an error code returned by
platform_get_irq() is completely invalid, don't attempt to overrule
irq subsystem in the driver.
The change fixes LPC32xx NAND MLC driver initialization on boot.
Fixes: 8cb17b5ed017 ("irqchip: Add LPC32xx interrupt controller driver")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When building with -Wmaybe-uninitialized, gcc produces a silly false positive
warning for the mtk_ecc_encode function:
drivers/mtd/nand/mtk_ecc.c: In function 'mtk_ecc_encode':
drivers/mtd/nand/mtk_ecc.c:402:15: error: 'val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The function for some reason contains a double byte swap on big-endian
builds to get the OOB data into the correct order again, and is written
in a slightly confusing way.
Using a simple memcpy32_fromio() to read the data simplifies it a lot
so it becomes more readable and produces no warning. However, the
output might not have 32-bit alignment, so we have to use another
memcpy to avoid taking alignment faults or writing beyond the end
of the array.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When changing from one data interface setting to another, one has to
ensure a specific sequence which is described in the ONFI spec.
One of these constraints is that the CE line has go high after a reset
before a command can be sent with the new data interface setting, which
is not guaranteed by the current implementation.
Rework the nand_reset() function and all the call sites to make sure the
CE line is asserted and released when required.
Also make sure to actually apply the new data interface setting on the
first die.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
|
|
We should disable the previously enabled GPMI clocks in the error paths.
Also, when gpmi_enable_clk() fails simply return the error
code immediately rather than jumping to to the 'err_out' label.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Pull MTD updates from Brian Norris:
"I've not been very active this cycle, so these are mostly from Boris,
for the NAND flash subsystem.
NAND:
- Add the infrastructure to automate NAND timings configuration
- Provide a generic DT property to maximize ECC strength
- Some refactoring in the core bad block table handling, to help with
improving some of the logic in error cases.
- Minor cleanups and fixes
MTD:
- Add APIs for handling page pairing; this is necessary for reliably
supporting MLC and TLC NAND flash, where paired-page disturbance
affects reliability. Upper layers (e.g., UBI) should make use of
these in the near future"
* tag 'for-linus-20161008' of git://git.infradead.org/linux-mtd: (35 commits)
mtd: nand: fix trivial spelling error
mtdpart: Propagate _get/put_device()
mtd: nand: Provide nand_cleanup() function to free NAND related resources
mtd: Kill the OF_MTD Kconfig option
mtd: nand: mxc: Test CONFIG_OF instead of CONFIG_OF_MTD
mtd: nand: Fix nand_command_lp() for 8bits opcodes
mtd: nand: sunxi: Support ECC maximization
mtd: nand: Support maximizing ECC when using software BCH
mtd: nand: Add an option to maximize the ECC strength
mtd: nand: mxc: Add timing setup for v2 controllers
mtd: nand: mxc: implement onfi get/set features
mtd: nand: sunxi: switch from manual to automated timing config
mtd: nand: automate NAND timings selection
mtd: nand: Expose data interface for ONFI mode 0
mtd: nand: Add function to convert ONFI mode to data_interface
mtd: nand: convert ONFI mode into data interface
mtd: nand: Introduce nand_data_interface
mtd: nand: Create a NAND reset function
mtd: nand: remove unnecessary 'extern' from function declarations
MAINTAINERS: Add maintainer entry for Ingenic JZ4780 NAND driver
...
|
|
Introduced by commit fde85cfd2d07 ("mtd: nand: Fix nand_command_lp() for
8bits opcodes") and I didn't have the heart to have Boris rewrite his
pull request just for that. Anyway, there's some value in having stable
commit hashes.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
"
Notable core changes:
- add the infrastructure to automate NAND timings configuration
- provide a generic DT property to maximize ECC strength
The rest is just a bunch of minor drivers and core fixes/cleanup
patches.
"
Also not noted: some refactoring in the core bad block table handling,
to help with improving some of the logic in error cases.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Pull late MTD fixes from Brian Norris:
"Another round of MTD fixes for v4.8
My apologies for sending this so late. I've been fairly absent as a
maintainer this cycle, but I did queue these up weeks ago. In the
meantime, Richard was able to handle some other fixes (thanks!) but
didn't pick these up.
On the bright side, these are very simple changes that should carry
little risk.
Summary:
- Davinci NAND: fix a long-standing bug in how we clear/prep 4-bit ECC
- OMAP NAND: an error-handling fix that made it into v4.8-rc1 caused
error-handling cases in other configurations/code-paths; this fixes
the fix"
* tag 'for-linus-20160928' of git://git.infradead.org/linux-mtd:
mtd: nand: davinci: Reinitialize the HW ECC engine in 4bit hwctl
mtd: nand: omap2: Don't call dma_release_channel() if dma_request_chan() failed
|
|
Provide a nand_cleanup() function to free all nand related resources
without unregistering the mtd device.
This should allow drivers to call mtd_device_unregister() and handle
its return value and still being able to cleanup all nand related
resources.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We are about to drop the OF_MTD Kconfig option. Test CONFIG_OF
activation instead of CONFIG_OF_MTD.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
8 bits opcodes should be followed by a single address cycle. Make the
2nd address cycle dependent of !nand_opcode_8bits(command).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Setup the maximum ECC config when NAND_ECC_MAXIMIZE is set.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Add support for ECC maximization when software BCH with
nand_ooblayout_lp_ops layout is used.
Other cases should be handled by the NAND controller driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.
In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).
Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
So far we relied on reset default or the bootloader to configure a
suitable clk rate for the Nand controller. This works but we can
optimize the timing for better performance. This sets the clk rate for
v2 controllers (i.MX25/35) based on the timing mode read from the ONFI
parameter page. This may also enable the symmetric mode (aks EDO mode)
if necessary which reads one word per clock cycle.
Tested on an i.MX25 with a Micron MT29F4G08ABBDAHC attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
To be able to support different ONFI timing modes we have to implement
the onfi_set_features and onfi_get_features. Tested on an i.MX25 SoC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The NAND framework is now able to select the best NAND timings for us.
All we have to do is implement a ->setup_data_interface() function to
apply those timings and remove the timing selection code from the sunxi
driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The NAND framework provides several helpers to query timing modes supported
by a NAND chip, but this implies that all NAND controller drivers have
to implement the same timings selection dance. Also currently NAND
devices can be resetted at arbitrary places which also resets the timing
for ONFI chips to timing mode 0.
Provide a common logic to select the best timings based on ONFI or
->onfi_timing_mode_default information. Hook this into nand_reset()
to make sure the new timing is applied each time during a reset.
NAND controller willing to support timings adjustment should just
implement the ->setup_data_interface() method.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The nand layer will need ONFI mode 0 to use it as timing mode
before and right after reset.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
onfi_init_data_interface() initializes a data interface with
values from a given ONFI mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
struct nand_data_interface is the designated type to pass to
the NAND drivers to configure the timing. To simplify further
patches convert the onfi_sdr_timings array from type struct
nand_sdr_timings nand_data_interface.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When NAND devices are resetted some initialization may have to be done,
like for example they have to be configured for the timing mode that
shall be used. To get a common place where this initialization can be
implemented create a nand_reset() function. This currently only issues
a NAND_CMD_RESET to the NAND device. The places issuing this command
manually are replaced with a call to nand_reset().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some Keystone devices (e.g. K2G) include a OMAP NAND IP.
Allow the NAND driver to be usable for both
Keystone and OMAP devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This patch adds big endian and ONFI support for various iProc based
SoCs that use the core brcmstb NAND controller
This patch was originally implemented by Prafulla Kota
<prafulla.kota@broadcom.com> and fully tested on iProc based NS2 SVK
Signed-off-by: Prafulla Kota <prafulla.kota@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
If erasing or writing the BBT fails, we should mark the current BBT
block as bad and use the BBT descriptor to scan for the next available
unused block in the BBT. We should only return a failure if there isn't
any space left.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Suggested-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This clarifies the write_bbt() function by removing the write label
and simplifying the error/exit path.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
|
|
In the ONFI spec, the tRR_min entry is defined before the tRST_max one.
Reoder the definition to make it easier to review.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
ONFI 4.0 spec defines different values for the tADL_min timing.
Since we don't want to have different timings depending on the ONFI
version, we just set tADL_min to the maximum value (the one specified
in the ONFI 4.0 spec).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
change the way to calculate pagesize to get correct free oob space for
legacy_set_geometry function.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some build tools noticed that 'cookie' is being set but not used. Might
as well catch the errors here and handle them the same way we handle
other DMA prep steps.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The driver registered for CPU frequency transitions to recalculate its
clock when ARM clock frequency changes (ratio between frequencies of
ARM's parent clock (fclk) and clock for peripherals remains fixed).
This is needed only on S3C24xx platform when cpufreq driver is enabled
so limit the ifdef to respective cpufreq Kconfig.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Using "goto" and "switch" statement only makes it harder to follow
control flow and doesn't bring any advantages. Rewrite the code to avoid
using "goto".
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
If no user specified chip->select_chip() function is provided, code in
nand_base.c will automatically set this hook to nand_select_chip(),
which in turn depends on chip->cmd_ctrl() hook being valid. Not
providing both of those functions in NAND controller driver (for example
by mistake) will result in a bit cryptic segfault. Same is true for
chip->cmdfunc().
To avoid the above scenario add a check in nand_scan_dent and error out
if cmd_ctrl() is not provided.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
