| Age | Commit message (Collapse) | Author |
|---|
|
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6f359df4f45152f2b40e1d4d1891392
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
|
|
This patch adds the driver/map for NOR devices attached to the SoC via the
External Bus Unit (EBU).
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/2285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
These changes were incorrectly fixed by codespell. They were now
manually corrected.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
* git://git.infradead.org/mtd-2.6:
mtd: atmel_nand: use CPU I/O when buffer is in vmalloc(ed) region
mtd: atmel_nand: modify test case for using DMA operations
mtd: atmel_nand: fix support for CPUs that do not support DMA access
mtd: atmel_nand: trivial: change DMA usage information trace
mtd: mtdswap: fix printk format warning
|
|
* 'for-linus' of git://git.infradead.org/ubifs-2.6:
UBI: do not select KALLSYMS_ALL
UBI: do not compare array with NULL
UBI: check if we are in RO mode in the erase routine
UBIFS: fix debugging failure in dbg_check_space_info
UBIFS: fix error path in dbg_debugfs_init_fs
UBIFS: unify error path dbg_debugfs_init_fs
UBIFS: do not select KALLSYMS_ALL
UBIFS: fix assertion warnings
UBIFS: fix oops on error path in read_pnode
UBIFS: do not read flash unnecessarily
|
|
All UBI needs is to make sure we stacktraces when UBI debugging
is enabled. It is enough to select KALLSYMS for this, KALLSYMS_ALL
is not necessary.
And the current Kconfig line we have:
select KALLSYMS_ALL if KALLSYMS && DEBUG_KERNEL
is just too complex to be sane and right. But this "if" part there
is needed to prevent "unmet direct dependency" warnings, because
KALLSYMS_ALL depends on KALLSYMS and DEBUG_KERNEL, so we cannot
just select KALLSYMS_ALL.
Anyway, this feels messy, and we do not seem to really need KALLSYMS_ALL,
so select KALLSYMS instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
|
|
Coverity spotted that UBI debugging code tries to compare
an array and NULL, which obviously makes little sense. Kill
this check.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
'do_sync_erase()' has to check whether we are in R/O mode before
erasing the PEB. This patch adds the check and while on it, adds an
assertion which validates the 'pnum' argument, as well as removes
a check which is always true because it has already been done
few lines before.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The previous way of dealing with vmalloc(ed) region by walking
though the pages can not work well actually. We just fall back
to CPU I/O when the buffer address is higher than `high_memory'.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
We have better performances not using DMA for oob operations.
Modify size test so that it is using DMA for size greater than oobsize.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
use_dma was always "1" even if the CPU does not support DMA
Tested on AT91SAM9261EK by Jean-Christophe PLAGNIOL-VILLARD
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The number is actually a sizeof(), so using %zu for it builds
cleanly on 32-bit or 64-bit.
drivers/mtd/mtdswap.c:1456: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into for-linus-1
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6: (9356 commits)
[media] rc: update for bitop name changes
fs: simplify iget & friends
fs: pull inode->i_lock up out of writeback_single_inode
fs: rename inode_lock to inode_hash_lock
fs: move i_wb_list out from under inode_lock
fs: move i_sb_list out from under inode_lock
fs: remove inode_lock from iput_final and prune_icache
fs: Lock the inode LRU list separately
fs: factor inode disposal
fs: protect inode->i_state with inode->i_lock
lib, arch: add filter argument to show_mem and fix private implementations
SLUB: Write to per cpu data when allocating it
slub: Fix debugobjects with lockless fastpath
autofs4: Do not potentially dereference NULL pointer returned by fget() in autofs_dev_ioctl_setpipefd()
autofs4 - remove autofs4_lock
autofs4 - fix d_manage() return on rcu-walk
autofs4 - fix autofs4_expire_indirect() traversal
autofs4 - fix dentry leak in autofs4_expire_direct()
autofs4 - reinstate last used update on access
vfs - check non-mountpoint dentry might block in __follow_mount_rcu()
...
NOTE!
This merge commit was created to fix compilation error. The block
tree was merged upstream and removed the 'elv_queue_empty()'
function which the new 'mtdswap' driver is using. So a simple
merge of the mtd tree with upstream does not compile. And the
mtd tree has already be published, so re-basing it is not an option.
To fix this unfortunate situation, I had to merge upstream into the
mtd-2.6.git tree without committing, put the fixup patch on top of
this, and then commit this. The result is that we do not have commits
which do not compile.
In other words, this merge commit "merges" 3 things: the MTD tree, the
upstream tree, and the fixup patch.
|
|
Fix the following compilation warning:
drivers/mtd/mtdswap.c: In function ‘mtdswap_pick_gc_eblk’:
drivers/mtd/mtdswap.c:859: warning: ‘idx’ may be used uninitialized in this function
drivers/mtd/mtdswap.c:859: note: ‘idx’ was declared here
Initialize idx to -1 because this value means "no tree choosen".
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
As Artem Bityutskiy suggested: this option is controversial, as we
do not really have any prove it is useful. And it is too much to have
it as a config parameter. So, better kill it and let the real mtdswap
users decide whether it is needed or not.
Signed-off-by: Yang Ruirui<ruirui.r.yang@tieto.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
* 'for-linus' of git://git.infradead.org/ubi-2.6:
UBIFS: fix assertion warning and refine comments
UBIFS: kill CONFIG_UBIFS_FS_DEBUG_CHKS
UBIFS: use GFP_NOFS properly
UBI: use GFP_NOFS properly
|
|
This patch fixes a brown-paperbag bug which was introduced by me:
I used incorrect "GFP_KERNEL | GFP_NOFS" allocation flags to make
sure my allocations do not cause write-back. But the correct form
is "GFP_NOFS".
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This silences warnings such as
drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type
These were added by me in commit 2a79bb1d.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use mfd_data for passing information from mfd drivers to mfd
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data(). This changes tmio-nand only; mfd drivers with
other cells are not modified.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (25 commits)
UBIFS: clean-up commentaries
UBIFS: save 128KiB or more RAM
UBIFS: allocate orphans scan buffer on demand
UBIFS: allocate lpt dump buffer on demand
UBIFS: allocate ltab checking buffer on demand
UBIFS: allocate scanning buffer on demand
UBIFS: allocate dump buffer on demand
UBIFS: do not check data crc by default
UBIFS: simplify UBIFS Kconfig menu
UBIFS: print max. index node size
UBIFS: handle allocation failures in UBIFS write path
UBIFS: use max_write_size during recovery
UBIFS: use max_write_size for write-buffers
UBIFS: introduce write-buffer size field
UBI: incorporate LEB offset information
UBIFS: incorporate maximum write size
UBI: provide LEB offset information
UBI: incorporate maximum write size
UBIFS: fix LEB number in printk
UBIFS: restrict world-writable debugfs files
...
|
|
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: make tests modes dynamic
UBI: make self-checks dynamic
UBI: make debugging messages dynamic
UBI: remove UBI_IO_DEBUG macro
UBI: kill debugging buffer
UBI: allocate erase checking buffer on demand
UBI: allocate write checking buffer on demand
UBI: always re-read in case of read failures
UBI: cleanup comments about corrupted PEBs
UBI: add slab cache for ubi_scan_leb objects
UBI: use raw mtd read function in debugging code
UBI: try to reveal buggy MTD drivers
UBI: add a commentary about allocating VID header buffer on stack
UBI: cleanup LEB start calculations
UBI: fix NOR erase preparation quirk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
|
|
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
|
|
* 'devicetree/next' of git://git.secretlab.ca/git/linux-2.6: (21 commits)
tty: serial: altera_jtaguart: Add device tree support
tty: serial: altera_uart: Add devicetree support
dt: eliminate of_platform_driver shim code
dt: Eliminate of_platform_{,un}register_driver
dt/serial: Eliminate users of of_platform_{,un}register_driver
dt/usb: Eliminate users of of_platform_{,un}register_driver
dt/video: Eliminate users of of_platform_{,un}register_driver
dt/net: Eliminate users of of_platform_{,un}register_driver
dt/sound: Eliminate users of of_platform_{,un}register_driver
dt/spi: Eliminate users of of_platform_{,un}register_driver
dt: uartlite: merge platform and of_platform driver bindings
dt: xilinx_hwicap: merge platform and of_platform driver bindings
ipmi: convert OF driver to platform driver
leds/leds-gpio: merge platform_driver with of_platform_driver
dt/sparc: Eliminate users of of_platform_{,un}register_driver
dt/powerpc: Eliminate users of of_platform_{,un}register_driver
dt/powerpc: move of_bus_type infrastructure to ibmebus
drivercore/dt: add a match table pointer to struct device
dt: Typo fix.
altera_ps2: Add devicetree support
...
|
|
Similarly to the debugging checks and message, make the test modes
be dynamically selected via the "debug_tsts" module parameter or
via the "/sys/module/ubi/parameters/debug_tsts" sysfs file. This
is consistent with UBIFS as well.
And now, since all the Kconfig knobs became dynamic, we can remove
the Kconfig.debug file completely.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch adds a possibility to dynamically switch UBI self-checks
on and off, instead of toggling them compile-time from the configuration
menu. This is much more flexible, and consistent with UBIFS, and this
also simplifies UBI Kconfig menu and the code.
This patch introduces two levels of self-checks - general, which
includes all self-checks which are relatively fast, and I/O, which
includes write-verify checks and erase-verify checks, which are
relatively slow and involve flash I/O.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch adds a possibility to dynamically select UBI debugging
messages, instead of selecting them compile-time from the configuration
menu. This is much more flexible, and consistent with UBIFS, and this
also simplifies UBI Kconfig menu and the code.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This additional little macro is used to print a bit more messages
while scanning the media. However, we have the 'dbg_bld()' macro
for this, so we better us 'dbg_bld()' and kill UBI_IO_DEBUG. This
simplifies the code a tiny bit.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch kills the 'ubi->dbg_peb_buf' debugging buffer and the
associated mutex, because all users of this buffer are now gone.
We are killing this buffer because we are going to switch to
dynamic debugging control, just like in UBIFS, which means that
CONFIG_MTD_UBI_DEBUG_PARANOID will be removed. In this case we'd
end up always allocating 'ubi->dbg_peb_buf', which is rather large
(128KiB or more), and this would be wasteful. Thus, we are just
killing it.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Instead of using pre-allocated 'ubi->dbg_peb_buf' buffer in
'ubi_dbg_check_all_ff()', dynamically allocate it when needed. The
intend is to get rid of the pre-allocated 'ubi->dbg_peb_buf' buffer
completely. And the need for this arises because we want to change
to dynamic debugging control instead of compile-time control, i.e.,
we are going to kill the CONFIG_MTD_UBI_DEBUG_PARANOID Kconfig
option, which would mean that 'ubi->dbg_peb_buf' is always allocated,
which would be wasteful.
Thus, we are getting rid of 'ubi->dbg_peb_buf', and this is a
preparation for that.
signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Instead of using pre-allocated 'ubi->dbg_peb_buf' buffer in
'ubi_dbg_check_write()', dynamically allocate it when needed. The
intend is to get rid of the pre-allocated 'ubi->dbg_peb_buf' buffer
completely. And the need for this arises because we want to change
to dynamic debugging control instead of compile-time control, i.e.,
we are going to kill the CONFIG_MTD_UBI_DEBUG_PARANOID Kconfig
option, which would mean that 'ubi->dbg_peb_buf' is always allocated,
which would be wasteful.
Thus, we are getting rid of 'ubi->dbg_peb_buf', and this is a
preparation for that.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into devel-stable
Conflicts:
arch/arm/mm/Kconfig
|
|
* git://git.infradead.org/users/dwmw2/mtd-2.6.38:
mtd: add "platform:" prefix for platform modalias
mtd: mtd_blkdevs: fix double free on error path
mtd: amd76xrom: fix oops at boot when resources are not available
mtd: fix race in cfi_cmdset_0001 driver
mtd: jedec_probe: initialise make sector erase command variable
mtd: jedec_probe: Change variable name from cfi_p to cfi
|
|
This patch adds option 'bch' to nandsim, which can be used to enable
software BCH ECC (introduced in previous patches) and select BCH error
correction capability.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds software BCH ECC support to mtd, in order to handle recent
NAND device ecc requirements (4 bits or more).
It does so by adding a new ecc mode (NAND_ECC_SOFT_BCH) for use by board
drivers, and a new Kconfig option to enable BCH support. It relies on the
generic BCH library introduced in a previous patch.
When a board driver uses mode NAND_ECC_SOFT_BCH, it should also set fields
chip->ecc.size and chip->ecc.bytes to select BCH ecc data size and required
error correction capability. See nand_bch_init() documentation for details.
It has been tested on the following platforms using mtd-utils, UBI and
UBIFS: x86 (with nandsim), arm926ejs.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Because malloc/kzalloc may fail, we should check kmalloc/kzalloc return value
in sm_create_sysfs_attributes(), mtd/sm_rtl.c and do error handling.
Meanwhile, we should check sm_create_sysfs_attributes return value.
Signed-off-by: Xiaochen Wang <wangxiaochen0@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Steffen Sledz <sledz@dresearch.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
When page size is 4KiB, ecc.total is set to 8*9, and this causes
nand_write_page_hwecc() to read past the initialized part of the eccpos array,
which corrupts chip->oob_poi with bogus values from ecc_calc.
Fix this by creating a proper nand_ecclayout for 4KiB flashes.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The DaVinci NAND driver was including the mach-types.h header
file.
This prevented the DaVinci NAND driver from getting used
in a DSP only device. The linux port on c6x devices can make
use of the same driver and does not define a corresponding
header file.
This header file was required in the driver because earlier there was code
dependent on a machine_* check. This piece of code has now been factored out
and is in arch/arm/mach-davinci/aemif.c
Thus removing the header file is harmless
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Use nand_scan_ident to unify the need of mtd member initilization
for both normal detection and keep configuration method.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Different NAND driver may require its unique detection. For pxa3xx_nand,
it use its self id database to get the necessary info.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Make the interface simpler which could make both debug
and enhancement easier.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Since we have rework the irq process, we don't need additional
delay in wait_for_event. Also write_cmd and __readid is also
discarded for the same reason.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Enable all irq when we start the nand controller, and
put all the transaction logic in the pxa3xx_nand_irq.
By doing this way, we could dramatically increase the
performance by avoid unnecessary delay.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
