| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 2cfe8f8290bd28cf1ee67db914a6e76cf8e6437b ]
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a4c61b92b3a4cbda35bb0251a5063a68f0861b2c ]
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f9c ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After discussing with Eric, it turns out that, while using
kexec_in_progress is a nice optimization, which prevents us from always
powering on the integrated PHY, let's just turn it on in the shutdown
path.
This removes a dependency on kexec_in_progress which, according to Eric
should not be used by modules
Fixes: 2399d6143f85 ("net: dsa: bcm_sf2: Prevent GPHY shutdown for kexec'd kernels")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For a kernel that is being kexec'd we re-enable the integrated GPHY in
order for the subsequent MDIO bus scan to succeed and properly bind to
the bcm7xxx PHY driver. If we did not do that, the GPHY would be shut
down by the time the MDIO driver is probing the bus, and it would fail
to read the correct PHY OUI and therefore bind to an appropriate PHY
driver. Later on, this would cause DSA not to be able to successfully
attach to the PHY, and the interface would not be created at all.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/dsa/bcm_sf2.ko | grep alias
alias: platform:brcm-sf2
After this patch:
$ modinfo drivers/net/dsa/bcm_sf2.ko | grep alias
alias: platform:brcm-sf2
alias: of:N*T*Cbrcm,bcm7445-switch-v4.0C*
alias: of:N*T*Cbrcm,bcm7445-switch-v4.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/dsa/bcm_sf2.c:963:19: warning:
symbol 'bcm_sf2_io_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While migrating the bcm_sf2 driver to use b53_common, we left a small
piece untouched where we kept our local copy of the per-port
port_vlan_ctl bitmask value. This value is now maintained by b53_device
so we need to use it instead of our local (and now stale) copy of it.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And while at it, remove the unecessary writing of zeroes to the CPU_MASK_CLEAR
register since it has no functional use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we are using b53_common for most VLAN, FDB and bridge
operations, delete all the redundant code that we had in bcm_sf2.c to
keep only the integration specific logic that we have to deal with:
power management, link management and the external interfaces (RGMII,
MDIO).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom Starfighter2 is almost entirely register compatible with
B53, yet for historical reasons came up first in the tree and is now
being updated to utilize b53_common.c to the fullest extent possible. A
few things need to be adjusted to allow that:
- the switch "core" registers currently operate on a 32-bit address,
whereas b53 passes a page + reg pair to offset from, so we need to
convert that, thankfully there is a generic formula to do that
- the link managemenent is not self contained with the B53/CORE register
set, but instead is in the SWITCH_REG block which is part of the
integration glue logic, so we keep that entirely custom here because
this really is part of the existing bcm_sf2 implementation
- there are additional power management constraints on the port's
memories that make us keep the port_enable/disable callbacks custom
for now, also, we support tagging whereas b53_common does not support
that yet
All the VLAN and bridge code is entirely identical though so, avoid
duplicating it. Other things will be migrated in the future like EEE and
possibly Wake-on-LAN.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we cannot complete bcm_sf2_sw_setup() for any reason, and we
go to the out_unmap label, but the MDIO bus has not been registered yet,
we will hit the BUG condition in drivers/net/phy/mdio_bus.c about the
bus not being registered. Fix this by dedicating a specific lable for
when we fail after the MDIO bus has been successfully registered.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-order the bcm_sf2_sw_setup() function so that it is at the far end of
the driver to avoid any kind of forward declarations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper function to fast age something that is controlled by the
caller: port, VLAN. We will use this to implement a VLAN fast age
operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.
We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are going to be more per-port members added to the switch
structure. So add a port structure and move the netdev into it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phys in phys_port_mask suggests this mask is about PHYs. In fact,
it means physical ports. Rename to enabled_port_mask, indicating
external enabled ports of the switch, which is hopefully less
confusing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the function called from the DSA to perform a probe for the
switch. This makes the normal _probe() name available for a standard
Linux device driver probe function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now the switch devices have a dev pointer, make use of it for allocating
the drivers private data structures using a devm_kzalloc().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By passing a device structure to the switch devices, it allows them
to use devm_* methods for resource management.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.
Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.
Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.
In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_upper_dev_unlink() which notifies NETDEV_CHANGEUPPER, returns
void, as well as del_nbp(). So there's no advantage to catch an eventual
error from the port_bridge_leave routine at the DSA level.
Make this routine void for the DSA layer and its existing drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename DSA port_join_bridge and port_leave_bridge routines to
respectively port_bridge_join and port_bridge_leave in order to respect
an implicit Port::Bridge namespace.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some DSA drivers may or may not support multiple software bridges on top
of an hardware switch.
It is more convenient for them to access the bridge's net_device for
finer configuration.
Removing the need to craft and access a bitmask also simplifies the
code.
This patch changes the signature of bridge related functions, update DSA
drivers, and removes dsa_slave_br_port_mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comparison check between cur_hw_state and hw_state is currently
invalid because cur_hw_state is right shifted by G_MISTP_SHIFT, while
hw_state is not, so we end-up comparing bits 2:0 with bits 7:5, which is
going to cause an additional aging to occur. Fix this by not shifting
cur_hw_state while reading it, but instead, mask the value with the
appropriately shitfted bitmask.
The other problem with the fast-ageing process is that we did not set
the EN_AGE_DYNAMIC bit to request the ageing to occur for dynamically
learned MAC addresses. Finally, write back 0 to the FAST_AGE_CTRL
register to avoid leaving spurious bits sets from one operation to the
other.
Fixes: 12f460f23423 ("net: dsa: bcm_sf2: add HW bridging support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SF2 driver currently overrides speed settings for its port
configured using a fixed PHY, this is both unnecessary and incorrect,
because we keep feedback to the hardware parameters that we read from
the PHY device, which in the case of a fixed PHY cannot possibly change
speed.
This is a required change to allow the fixed PHY code to allow
registering a PHY with a link configured as DOWN by default and avoid
some sort of circular dependency where we require the link_update
callback to run to program the hardware, and we then utilize the fixed
PHY parameters to program the hardware with the same settings.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Utilize the newly introduced BRCM_PSEUDO_PHY_ADDR constant from
brcmphy.h instead of open-coding the Broadcom Ethernet switches
pseudo-PHY address (30).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MoCA interfaces require the use of an user-space daemon (mocad) which
will typically use cmd->autoneg to force the link. This is causing other
network manager applications not to get proper carrier down
notifications because of the following sequence of events:
- link down interrupt is received, link is set to 0 by the interrupt
handler
- fixed_link update callback runs and updates the BMSR register
accordingly
- PHY library polls the PHY for link status, sees the link is down,
proceeds with reporting that
- mocad gets notified of the link state and call phy_ethtool_sset()
with cmd->autoneg set to the link status (0)
- phy_start_aneg() is called at the end of phy_ethtool_sset() and sets
the PHY state to PHY_FORCING
Just make sure we notify the interface carrier appropriately when we
detect that the link is down in our fixed_link update callback. This is
made local to the bcm_sf2 driver as the PHY library does the right thing
in any case. This is similar to the GENET change introduced in
54d7c01d3ed699cfc213115eaecfe1175cfaff8f ("net: bcmgenet: enable MoCA
link state change detection").
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.
Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the code that touches the single GPHY register from
bcm_sf2_sw_resume() to a separate function since we will have to
enable/disable the GPHY from different locations, and we want the code
to be self-contained.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor the interrupt disabling in a function: bcm_sf2_intr_disable()
since we are doing the same thing in the setup and suspend paths.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.
For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When EEE is enabled, negotiate this feature with the PHY and make sure
that the capability checking, local EEE advertisement, link partner EEE
advertisement and auto-negotiation resolution returned by phy_init_eee()
is positive, and enable EEE at the switch level.
While querying the current EEE settings, verify the low-power indication
and indicate its status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SF2 switch driver is already architected around per-port
enable/disable callbacks, so we just need a slight update to our
existing bcm_sf2_port_setup() resp. bcm_sf2_port_disable() functions to
be suitable as callbacks for port_enable/port_disable.
We need to shuffle a little the code that does the per-port VLAN
configuration/isolation since ports can now be brought up/down
separately, so we need to make sure that IMP (CPU, management) port is
always included in that specific port setup.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
