| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 5bc8c230e2a993b49244f9457499f17283da9ec7 ]
i210 and i211 share the same PHY but have different PCI IDs. Don't
forget i211 for any i210 workarounds.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4e684f59d760a2c7c716bb60190783546e2d08a1 ]
Sometimes firmware may not properly initialize I347AT4_PAGE_SELECT causing
the probe of an igb i210 NIC to fail. This patch adds an addition zeroing
of this register during igb_get_phy_id to workaround this issue.
Thanks for Jochen Henneberg for the idea and original patch.
Signed-off-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.
In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.
Fixes: b83e30104bd9 ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.
In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.
Fixes: e10715d3e961 ("igb/igbvf: Add support for GSO partial")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Order of arguments is wrong.
The wrong code has been introduced by commit 7d4f8d871ab1, but is compiled
only since commit 9df70b66418e.
Note that this may break netlink dumps.
Fixes: 9df70b66418e ("i40e: Remove incorrect #ifdef's")
Fixes: 7d4f8d871ab1 ("switchdev; add VLAN support for port's bridge_getlink")
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If we fail on allocating enough MSI-X interrupts, we should disable
them since they were previously enabled in this point of code.
Not disabling them can lead to WARN_ON() being triggered and subsequent
failure in enabling MSI as a fallback; the below message was shown without
this patch while we played with interrupt allocation in i40e driver:
[ 21.461346] sysfs: cannot create duplicate filename '/devices/pci0007:00/0007:00:00.0/0007:01:00.3/msi_irqs'
[ 21.461459] ------------[ cut here ]------------
[ 21.461514] WARNING: CPU: 64 PID: 1155 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x88/0xc0
Also, we noticed that without this patch, if we modprobe the module without
enough MSI-X interrupts (triggering the above warning), unload the module
and re-load it again, we got a crash on the system.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
in commit a036244c068612a43fa8c0f33a0eb4daa4d8dba0 a fix
was put into place to avoid a kernel panic when a non-
supported traffic class configuration was put into place
and then lldp was enabled/disabled on the link partner
switch. This fix caused it to be necessary to
unload/reload the driver to reenable DCB once a supported
TC config was in place.
The root cause of the original panic was that the function
i40e_pf_get_default_tc was allowing for a default TC other
than TC 0, and only TC 0 is supported as a default.
This patch removes the get_default_tc function and replaces
it with a #define since there is only one TC supported as
a default.
Change-Id: I448371974e946386d0a7718d73668b450b7c72ef
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix NULL pointer dereference in the case where a macvlan interface is
brought up while the PF is still down:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffffa0170fb2>] ixgbe_alloc_rx_buffers+0x42/0x1a0 [ixgbe]
Call Trace:
[<ffffffffa017336b>] ixgbe_configure_rx_ring+0x2eb/0x3d0 [ixgbe]
[<ffffffffa0173811>] ixgbe_fwd_ring_up+0xd1/0x380 [ixgbe]
[<ffffffffa0179709>] ixgbe_fwd_add+0x149/0x230 [ixgbe]
[<ffffffffa0113480>] macvlan_open+0x260/0x2b0 [macvlan]
Reported-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-10-02
This series contains updates to fm10k only.
Jake fixes an issue where PTP applications requesting software timestamps
may complain that the requested mode is not supported, so add a generic
callback for those drivers that have software transmit timestamp support
enabled. Then provides a trivial cleanup where a code was not wrapped
properly. Got make sure that code looks good in a 80 character limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.
Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Trivial change here to cleanup a checkpatch.pl warning that got
introduced when changing to alloc_workqueue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This generic callback is for drivers which have software Tx timestamp
support enabled. Without this, PTP applications requesting software
timestamps may complain that the requested mode is not supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a reset occurs, the PPS SYS_WRAP interrupt was not re-enabled which
resulted in disabling of the PPS signaling. Fix this by recording when
the interrupt is on and ensuring that we re-enable it every time we
reset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump igb version to match other igb drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump version to match other igbvf drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/intel/igb/igb_ethtool.c:2707:5: warning:
symbol 'igb_rxnfc_write_vlan_prio_filter' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit a75e8005d506f3 ("i40e: queue-specific settings for interrupt
moderation") the i40e driver gained support for setting interrupt
moderation values per queue. This patch adds support for this feature
to the i40evf driver as well. In addition, a few changes are made to
the i40e implementation to add function header documentation comments,
as well.
This behaves in a similar fashion to the implementation in i40e. Thus,
requesting the moderation value when no queue is provided will report
queue 0 value, while setting the value without a queue will set all
queues at once.
Change-ID: I1f310a57c8e6c84a8524c178d44d1b7a6d3a848e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some rare cases, we might get a VSI with no queues. In this case, we
cannot configure RSS on this VSI as it will try to divide by zero when
configuring the lookup table.
Change-ID: I6ae173a7dd3481a081e079eb10eb80275de2adb0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This interface was only ever meant for debug only. Since it is not
supposed to be here we are removing it.
Change-ID: Id771a1e5e7d3e2b4b7f56591b61fb48c921e1d04
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In an effort to improve code readability I am splitting the Flow Director
filter configuration out into a separate function like we have done for the
standard xmit path. The general idea is to provide a single block of code
that translates the flow specification into a proper Flow Director
descriptor.
Change-ID: Id355ad8030c4e6c72c57504fa09de60c976a8ffe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a txring_txq function which allows us to convert a
i40e_ring/i40evf_ring to a netdev_tx_queue structure. This way we
can avoid having to make a multi-line function call for all the spots
that need access to this.
Change-ID: Ic063b71d8b92ea406d2c32e798c8e2b02809d65b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Tx cleanup flow was incorrectly assuming it could check for the flow
director bits after it had unmapped the buffer. However in this case it
results in us trying to free a raw_buf as though it is an sk_buff.
To fix this I am moving up the flag test for the FD_SB bit so that when
find a non-NULL skb or raw_buf value we then check the flag and use the
appropriate call to free the buffer.
Change-ID: I6284034ba1ea87c9922e56f6eb3181f7f09bddde
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
All of the code to support adaptive interrupt throttling is already in
the interrupt handler, it just needs to be enabled. Fill out the data
structures properly to make it happen. Single-flow traffic tests may
show slightly lower throughput, but interrupts per second will drop by
about 75%.
Change-ID: I9cd7d42c025b906bf1bb85c6aeb6112684aa6471
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch increases minimum number of allocated VSIs, so as to resolve
failure adding VSI for VF when 64-VFs assigned to a PF. The driver
supports up to 128 VFs per device, users can decide to enable up to
64-VFs on a single PF, especially 2 X 40 devices. In that scenario, with
VMDq co-existence, there would be starvation of VSIs - with this patch,
supported features would have enough VSIs for configuration now.
Change-ID: If084f4cd823667af8fe7fdc11489c705b32039d5
Signed-off-by: Akeem Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The return value from i40e_shutdown_adminq() is always 0
(I40E_SUCCESS). So, the test for non-0 will never be true. Cleanup
by removing the test and debug print statement.
Change-ID: Ie51e8e37515c3e3a6a9ff26fa951d0e5e24343c1
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In i40e_fdir_check_and_reenable(), the driver performs some checks to
determine whether it is safe to re-enable FD Sideband and FD ATR
support. The current check will only determine if there is available
space in the flow director table. However, this ignores the fact that
ATR should be disabled when there are TCP/IPv4 sideband rules in effect.
Add the missing check, and update the info message printed when
I40E_DEBUG_FD is enabled.
Change-ID: Ibb9c63e5be95d63c53a498fdd5dbf69f54a00e08
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.
Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.
Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.
Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add ENCAP_CSUM offload negotiation flag. Currently VF assumes checksum
offload for encapsulated packets is supported by default. Going forward,
this feature needs to be negotiated with PF before advertising to the
stack. Hence, we need a flag to control it.
This is in regards to prepping up for VF base mode functionality support.
Change-ID: Iaab1f25cc0abda5f2fbe3309092640f0e77d163e
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There exists a bug in which deleting a mac filter does not actually
occur. The driver reports that the filter has been deleted with no
error. The problem occurs because the wrong cmd_flag is passed to the
firmware when deleting the filter. The firmware reports an error back
to the driver but it is expressly ignored.
This fixes the bug by using the correct flag when deleting a filter.
Without this patch, deleted filters remain in firmware and function as
if they had not been deleted.
Change-ID: I5f22b874f3b83f457702f18f0d5602ca21ac40c3
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the problem where driver shows 100 Mbps as a supported speed,
and allows it to be configured for advertising on X722 devices. This patch
fixes the problem by not setting the 100 Mbps SGMII flag for X722 devices.
Without this patch, the user incorrectly thinks that 100 Mbps is supported
and hence might try to advertise it on X722 devices when it is actually not
a supported speed.
Change-ID: I8c3d7c4251a9402d98994ed29749b7b895a0f205
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-09-23
This series contains updates to ixgbe and ixgbevf.
Emil provides several changes, first simplifies the logic for setting VLAN
filtering by checking the VMDQ flag and the old 82598 MAC, instead of
having to maintain a list of MAC types. Then made two functions static
that are used only within the file, a by-product is sparse is now happy.
Added spinlocks to make sure that the MTU configuration is handled
properly. Fixed an issue where when SR-IOV is enabled while the
ixgbevf driver is loaded would result in all mailbox requests being
rejected by ixgbe, so call ixgbe_sriov_reinit() before pci_enable_sriov()
to ensure mailbox requests are properly handled.
Mark resolves a NULL pointer issue by simply setting the read and write
*_ref_mdi pointers for x550em_a devices. Then clearly indicates within
ethtool that all MACs support pause frames and made sure that the
advertising is set to the requested mode. Fixed an issue where
MDIO_PRTAD_NONE was not being used consistently to indicate no PHY
address.
Alex fixes an issue, where the support for multiple queues when SR-IOV
is enabled was added but the support was not reported. With that, fix
an issue where the hardware redirection table could support more queues
then the PF currently has when SR-IOV is enabled, so use the RSS mask to
trim off the bits that are not used. Lastly, instead of limiting the
VFs if we do not use 4 queues for RSS in the PF, we can instead just limit
the RSS queues used to a power of 2. We can now support use cases where
VFs are using more queues than the PF is currently using and can support
RSS if so desired.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-09-22
This series contains updates to i40e and i40evf only.
Sridhar fixes link state event handling by updating the carrier and
starts/stops the Tx queues based on the link state notification from PF.
Brady fixes an issue where a user defined RSS hash key was not being
set because a user defined indirection table is not supplied when changing
the hash key, so if an indirection table is not supplied now, then a
default one is created and the hash key is correctly set. Also fixed
an issue where when NPAR was enabled, we were still using pf->mac_seid
to perform the dump port query. Instead, go through the VSI to determine
the correct ID to use in either case.
Mitch provides one fix where a conditional return code was reversed, so
he does a "switheroo" to fix the issue.
Carolyn has two fixes, first fixes an issue in the virt channel code,
where a return code was not checked for NULL when applicable. Second,
fixes an issue where we were byte swapping the port parameter, then
byte swapping it again in function execution.
Colin Ian King fixes a potential NULL pointer dereference.
Bimmy changes up i40evf_up_complete() to be void since it always returns
success anyways, which allows cleaning up of code which checked the
return code from this function.
Alex fixed an issue where the driver was incorrectly assuming that we
would always be pulling no more than 1 descriptor from each fragment.
So to correct this, we just need to make certain to test all the way to
the end of the fragments as it is possible for us to span 2 descriptors
in the block before us so we need to guarantee that even the last 6
descriptors have enough data to fill a full frame.
v2: dropped patches 1-3, 10 and 12 from the original series since Or
Gerlitz pointed out several areas of improvement in the implementation
of the VF Port representor netdev. Sridhar is re-working the series
for later submission.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling SRIOV while the ixgbevf driver is loaded will result in all
mailbox requests from ixgbevf_open() being rejected by ixgbe because
adapter->clear_to_send is set to false on reset.
Call ixgbe_sriov_reinit() before pci_enable_sriov() to make sure that
mailbox requests are handled from the time ixgbevf is loaded.
Reported-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of limiting the VFs if we don't use 4 queues for RSS in the PF we
can instead just limit the RSS queues used to a power of 2. By doing this
we can support use cases where VFs are using more queues than the PF is
currently using and can support RSS if so desired.
The only limitation on this is that we cannot support 3 queues of RSS in
the PF or VF. In either of these cases we should fall back to 2 queues in
order to be able to use the power of 2 masking provided by the psrtype
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The hardware redirection table can support more queues then the PF
currently has when SR-IOV is enabled. In order to account for this use the
RSS mask to trim of the bits that are not used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The maximum queue count reported was 1, however support for multiple queues
with SR-IOV was added some time ago so we should report support for it to
the user so that they can select multiple queues if they so desire.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The value MDIO_PRTAD_NONE should be used to indicate no PHY address.
Not 0, not 0xFFFF. Use the MDIO_PRTAD_NONE value consistently.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Protect set_rlpml with mailbox lock to make sure the MTU configuration
is handled properly.
This change resolves an issue where set_rlpml can fail when the VF
interface is brought up:
ixgbevf 0000:03:1d.6: Failed to set MTU at 1500
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
All the MACs supported by ixgbe support pause frames, so indicate
that support in ethtool. Also set advertising according to requested
mode.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set the read_reg_mdi and write_reg_mdi method pointers for
X550EM_A_10G_T devices to resolve jumping to NULL.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These functions are only used in ixgbe_x550.c.
Fixes a warning when compiling with -Wmissing-prototypes
Reported-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Simplify the logic for setting VLNCTRL.VFE by checking the VMDQ flag
and 82598 MAC instead of having to maintain a list of MAC types.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e_shutdown_adminq function never returns failure. There is no need to
check the non-0 return value. Clean up the unnecessary error checking and
warning against it.
Change-ID: Ibb616f09cfb93bd1a872ebf3241a15fb8354b31b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e driver was incorrectly assuming that we would always be pulling
no more than 1 descriptor from each fragment. It is in fact possible for
us to end up with the case where 2 descriptors worth of data may be pulled
when a frame is larger than one of the pieces generated when aligning the
payload to either 4K or pieces smaller than 16K.
To adjust for this we just need to make certain to test all the way to the
end of the fragments as it is possible for us to span 2 descriptors in the
block before us so we need to guarantee that even the last 6 descriptors
have enough data to fill a full frame.
Change-ID: Ic2ecb4d6b745f447d334e66c14002152f50e2f99
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Function i40evf_up_complete() always returns success. Changed this to a
void type and removed the code that checks the return status and prints
an error message.
Change-ID: I8c400f174786b9c855f679e470f35af292fb50ad
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
