| Age | Commit message (Collapse) | Author |
|---|
|
The interrupt worker code for the enc28j60 relies only on the TXIF flag to
determinate if the packet transmission was completed. However the datasheet
specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
transmit abort. Also in section 12.1.4 that TXIF will be set
when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
during transmission errors.
This causes a race condition, since the worker code will invoke
enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
called, the worker from the interrupt handler will enter the path for error
handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
and releasing the packet scheduled for transmission, causing a kernel crash with
due a NULL pointer.
These crashes due a NULL pointer were observed under stress conditions of the
device. A BUG_ON() sequence was used to validate the issue was fixed, and has
been running without problems for 2 years now.
Signed-off-by: Diego Dompe <dompe@hpe.com>
Acked-by: Sergio Valverde <sergio.valverde@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following patch adds the required match table for device tree support
(and while at, fix the indent). It's also possible to specify the
MAC address in the DT blob.
Also add the corresponding binding documentation file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current spi_read_buf function fails on SPI host masters which
are only half-duplex capable. Splitting the Tx and Rx part solves
this issue.
Tested on Raspberry Pi (full duplex) and I2SE Duckbill (half duplex).
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replace it by ndo_set_rx_mode
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.
CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
