| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 171f6402e4aa ("ath9k_hw: implement temperature compensation
support for AR9003+"). Some users report that this commit causes a regression
in performance under some conditions.
Fixes: 171f6402e4aa ("ath9k_hw: implement temperature compensation support for AR9003+")
Cc: <stable@vger.kernel.org> # 4.8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
commit 61b559dea40e ("ath9k: add extra GPIO led support")
added ath9k to support access SOC's GPIOs, but implemented
in a separated API: ath9k_hw_request_gpio().
So this patch make the APIs more common, to support both
of WMAC and SOC GPIOs. The new APIs as below,
void ath9k_hw_gpio_request_in();
void ath9k_hw_gpio_request_out();
void ath9k_hw_gpio_free();
NOTE, the BSP of the SOC chips(AR9340, AR9531, AR9550, AR9561)
should set the corresponding MUX registers correctly.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Define correct GPIO numbers and MASK bits to indicate the WMAC
GPIO resource.
Allow SOC chips(AR9340, AR9531, AR9550, AR9561) to access all GPIOs
which rely on gpiolib framework. But restrict SOC AR9330 only to
access WMAC GPIO which has the same design with the old chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
|
|
rename the variable as preparation for using the array with 2.4 GHz
band, etc.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ar9002_hw_spur_mitigate.
[ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code.
This patch will move common part of ar5008_hw_spur_mitigate to
ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate.
As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of
declarations for pilot_mask_reg and chan_mask_reg.
There should be no other difference with original code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ar9550 or later chips, the AR_GPIO_IN_OUT register only can
control GPIO[0:3]. For the extra GPIO, use standard GPIO calls
instead of WMAC internal registers.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since usb bus add extra delay on each request, a command
with read + write requests is too expensive. We can dramtically
reduce usb load by moving this command to firmware.
In my tests, this patch will reduce channel scan time
for about 5-10 seconds.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
AIC needs to be registered only when BTCOEX is enabled.
This fixes the error reported by kbuild:
>> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Cards based on AR9462/AR9565 support more PCIE
power save mechanisms, so register them correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use the value in ah->config.pll_pwrsave to determine
which array needs to be loaded. Also, initialize
pll_pwrsave to 1 by default.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These will be used to handle chip-specific
power save configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch addresses several issues with the
ath9k_hw_wow_enable() routine:
* The usage of set/clr variables is removed. Writing
the required values to registers is cleaner.
* The shift value of 28 for the contention window field
in AR_WOW_PATTERN is incorrect, change it to 27.
* Disabling Keep Alive needs to be done based on the
LINK_CHANGE option. This is done unconditionally now,
fix this.
* The workaround for the D1/D3 issue is required only
for AR9462.
* The bitfield for enabling pattern matching for packets
less than 256 bytes has expanded for new chips, handle
this accordingly.
* General cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Newer chips like WB222, WB335 support more than
8 user-configurable patterns. This patch adds
support for it by setting up the correct HW
registers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the maximum number of configurable patterns
is chip-specific, use the HW capability instead
of a fixed value for checking if a free pattern
slot is available.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the number of patterns that can be configured in
the HW is higher for newer chips, store the chip-specific
value in ath9k_hw_wow.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This can be used to hold the WOW state in
ath9k_hw.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Printing the value of the wakeup status is sufficient.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enabling WOW based on the chip is incorrect since
it needs to be done for specific sub-devices which
have proper platform support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add TX power per-rate tables for MIMO/legacy modes for AR9002 based chips
in order to cap the maximum TX power value per-rate in the TX descriptor path.
Add TX power adjustments for HT40 mode, open loop CCK rates and eeprom power
bias for AR9280 and later chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some devices have multiple bands enables in the EEPROM data, even though
they are only calibrated for one. Allow platform data to disable
unsupported bands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On some devices (especially little-endian ones), the flash EEPROM data
has a different endian, which needs to be detected.
Add a flag to the platform data to allow overriding that behavior
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When NF calibration fails, the radio often becomes deaf. The usual
hardware hang checks do not detect this, so it's better to issue a reset
when that happens.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The initvals use up quite a bit of space, and PC-OEM support is
typically not needed on embedded systems
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On AR9003, tx control and tx status are in separate descriptor rings.
Tx duration is extracted from the tx control descriptor data, which
ar9003_hw_proc_txdesc cannot access.
Fix getting the duration by adding a separate callback for it.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Tested-by: Philippe Duchein <wireless-dev@duchein.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A full HW reset is not required for all baseband watchdog
signatures. Some BB watchdog updates are benign and can
be discarded, some require re-programming of certain registers
and others require a chip reset.
This patch adds a routine to identify such signatures.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is required for adding separate hang check
routines for AR9002 and AR9003.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
HW hang checks have to be done on a per-chip basis.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_hw should not depend on any ath9k data structures like ath_softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove unused fields, pass timer info in usec instead of TU.
Preparation for fixing nexttbtt calculation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is unused
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
