| Age | Commit message (Collapse) | Author |
|---|
|
* Fix bad udelay calls (using > 2000us) in AR5210 code and clean up
some bits on nic_reset (AR5210 support is still in bad shape)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* No code changes...
* Split hw.c to multiple files for better maintenance and add some documentation on each file
code is going to grow soon (eeprom.c for example is going to get much stuff currently developed
on ath_info) so it's better this way.
* Rename following functions to maintain naming scheme:
ah_setup_xtx_desc -> ah_setup_mrr_tx_desc
(Because xtx doesn't say much, it's actually
a multi-rate-retry tx descriptor)
ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp
ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp
(We don't put any "buf" we set descriptor pointers on hw)
ath5k_hw_tx_start -> ath5k_hw_start_tx_dma
ath5k_hw_start_rx -> ath5k_hw_start_rx_dma
ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu
(It's easier this way to identify them, we also
have ath5k_hw_start_rx_pcu which completes the
set)
ath5k_hw_set_intr -> ath5k_hw_set_imr
(As in get_isr we set imr here, not "intr")
* Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can
include support for different rx descriptors in the future
* Further cleanups so that checkpatch doesn't complain
(only some > 80 col warnings for eeprom.h and reg.h as usual
due to comments)
Tested on 5211 and 5213 cards and works ok.
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Enable I/Q calibration each time we have correction results (we
were only enabling calibration during reset). If we don't we commit
the same results each time calibration routine is called.
* Add some documentation and a TODO on nf calibration
* Return -EAGAIN on noise floor timeout/failure
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Add channel function for RF2425 (got this from decompiling binary
HAL, i have no idea why there is a 5GHz section but i'm looking
into it)
* Update RF5112 channel function (also got this from decompiling binary HAL)
* Set JAPAN setting for channel 14 on all PHY chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Add initial RF gain settings for RF2425
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
*Add RF2425 initvals (still no rx/tx)
This was on my laptop for a long time so it has to go out even if
it still doesn't work, i hope i'll get my hands on an eeepc so i can
work this out.
base.c
Changes-licensed-under: 3-clause-BSD
rest
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
(test == true) is not nice.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Since RF2413 it seems that RF_BUFFER settings are different (notice
that the last part -"bank 7" or whatever- is smaller than in 5111/5112).
So until we know what's going on we assume there is no gain optimization
stuff in post-5112 chips.
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Add AR5K_RF2413 to radio check during hw_reset so it doesn't complain
* Write ah_phy_spending value we set during attach instead of checking
each time for radio revision
* Skip txpower setup for RF2413 because it can't transmit with it
(weird thing is that RF5413 has no problem with it).
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Add initial settings for RF2413
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Author: Adrian Bunk <bunk@kernel.org>
This patch fixes a negative array index spotted by the Coverity checker.
Changes-licensed-under: ISC
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cleanup after API changes patch (checkpatch.pl stuff) and on
ath5k_hw_channel() make use of the existing ath5k_channel_ok()
instead of re-implementing the checks again. This was necessary
to make the code cleaner and fit the 80-chars wide limit so
sending it within the same patch.
Finally make a note that we *may* eventually move cap_range stuff
to struct wiphy (band frequency range capabilities). This
information can later be exported to userspace, for example,
and giving it access to mac80211 and drivers in general can come
in handy.
Changes to initvals.c, phy.c
Changes-licensed-under: ISC
Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Author: Nick Kossifidis <mickflemm@gmail.com>
Tested on 5211, 5213+5112, 5213A+2112A and it wors fine.
Also i figured out a way to process rate vallue found
on status descriptors, it's still buggy but we are getting
closer (i think it improved stability a little).
Changes to hw.c, initvals.c, phy.c
Changes-licensed-under: ISC
Changes to ath5k.h, base.c, base.h
Changes-licensed-under: 3-Clause-BSD
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
add ath5k wireless driver
Portions of this driver are covered by one or both of the ISC and
3-clause BSD licenses. Specific license information is cited at the top
of each file.
Acked-by and Signed-off-by information is collected from individual
patches as collected in the wireless-2.6 tree prior to upstream
submission.
Acked-by: Matthew W. S. Bell <mentor@madwifi.org>
Acked-by: Michael Taylor <mike.taylor@apprion.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bradley M. Kuhn <bkuhn@softwarefreedom.org>
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Karen Sandler <karen@softwarefreedom.org>
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Matt Norwood <norwood@softwarefreedom.org>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Richard Fontana <fontana@softwarefreedom.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Ulrich Meis <meis@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
