Age | Commit message (Collapse) | Author |
|
[ Upstream commit d53628882255481b710641dd0118fbd80af6e983 ]
ieee80211_unregister_hw() might invoke operations to stop the interface,
that uses the hal_mutex. So don't destroy it until after we're done
using it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7f622593cc5add77a99cd39404e8a851be9de792 ]
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0a744d927406389e00687560d9ce3c5ab0e58db9 ]
Station pointers are RCU protected so driver must
be extra careful if it tries to store them
internally for later use outside of the RCU
section it obtained it in.
It was possible for station teardown to race with
some htt events. The possible outcome could be a
use-after-free and a crash.
Only peer-flow-control capable firmware was
affected (so hardware-wise qca99x0 and qca4019).
This could be done in sta_state() itself via
explicit synchronize_net() call but there's
already a convenient sta_pre_rcu_remove() op that
can be hooked up to avoid extra rcu stall.
The peer->sta pointer itself can't be set to
NULL/ERR_PTR because it is later used in
sta_state() for extra sanity checks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f35a7f91f66af528b3ee1921de16bea31d347ab0 upstream.
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfb5b098e0f40b68aa07f2ec55f4dd762efefbfa upstream.
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18ae68fff392e445af3c2d8be9bef8a16e1c72a7 upstream.
WMI ops wrappers did not properly check for null
function pointers for spectral scan. This caused
null dereference crash with WMI-TLV based firmware
which doesn't implement spectral scan.
The crash could be triggered with:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
The crash looked like this:
[ 168.031989] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 168.037406] IP: [< (null)>] (null)
[ 168.040395] PGD cdd4067 PUD fa0f067 PMD 0
[ 168.043303] Oops: 0010 [#1] SMP
[ 168.045377] Modules linked in: ath10k_pci(O) ath10k_core(O) ath mac80211 cfg80211 [last unloaded: cfg80211]
[ 168.051560] CPU: 1 PID: 1380 Comm: bash Tainted: G W O 4.8.0 #78
[ 168.054336] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 168.059183] task: ffff88000c460c00 task.stack: ffff88000d4bc000
[ 168.061736] RIP: 0010:[<0000000000000000>] [< (null)>] (null)
...
[ 168.100620] Call Trace:
[ 168.101910] [<ffffffffa03b9566>] ? ath10k_spectral_scan_config+0x96/0x200 [ath10k_core]
[ 168.104871] [<ffffffff811386e2>] ? filemap_fault+0xb2/0x4a0
[ 168.106696] [<ffffffffa03b97e6>] write_file_spec_scan_ctl+0x116/0x280 [ath10k_core]
[ 168.109618] [<ffffffff812da3a1>] full_proxy_write+0x51/0x80
[ 168.111443] [<ffffffff811957b8>] __vfs_write+0x28/0x120
[ 168.113090] [<ffffffff812f1a2d>] ? security_file_permission+0x3d/0xc0
[ 168.114932] [<ffffffff8109b912>] ? percpu_down_read+0x12/0x60
[ 168.116680] [<ffffffff811965f8>] vfs_write+0xb8/0x1a0
[ 168.118293] [<ffffffff81197966>] SyS_write+0x46/0xa0
[ 168.119912] [<ffffffff818f2972>] entry_SYSCALL_64_fastpath+0x1a/0xa4
[ 168.121737] Code: Bad RIP value.
[ 168.123318] RIP [< (null)>] (null)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07246c115801c27652700e3679bb58661ef7ed65 upstream.
The bug was triggered when do suspend/resuming continuously
on Dell XPS L322X/0PJHXN version 9333 (2013) with kernel
4.12.0-041200rc4-generic. But can't reproduce on DELL
E5440 + AR9300 PCIE chips.
The warning is caused by accessing invalid pointer sc->rng_task.
sc->rng_task is not be cleared after kthread_stop(sc->rng_task)
be called in ath9k_rng_stop(). Because the kthread is stopped
before ath9k_rng_kthread() be scheduled.
So set sc->rng_task to null after kthread_stop(sc->rng_task) to
resolve this issue.
WARNING: CPU: 0 PID: 984 at linux/kernel/kthread.c:71 kthread_stop+0xf1/0x100
CPU: 0 PID: 984 Comm: NetworkManager Not tainted 4.12.0-041200rc4-generic #201706042031
Hardware name: Dell Inc. Dell System XPS L322X/0PJHXN, BIOS A09 05/15/2013
task: ffff950170fdda00 task.stack: ffffa22c01538000
RIP: 0010:kthread_stop+0xf1/0x100
RSP: 0018:ffffa22c0153b5b0 EFLAGS: 00010246
RAX: ffffffffa6257800 RBX: ffff950171b79560 RCX: 0000000000000000
RDX: 0000000080000000 RSI: 000000007fffffff RDI: ffff9500ac9a9680
RBP: ffffa22c0153b5c8 R08: 0000000000000000 R09: 0000000000000000
R10: ffffa22c0153b648 R11: ffff9501768004b8 R12: ffff9500ac9a9680
R13: ffff950171b79f70 R14: ffff950171b78780 R15: ffff9501749dc018
FS: 00007f0d6bfd5540(0000) GS:ffff95017f200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc190161a08 CR3: 0000000232906000 CR4: 00000000001406f0
Call Trace:
ath9k_rng_stop+0x1a/0x20 [ath9k]
ath9k_stop+0x3b/0x1d0 [ath9k]
drv_stop+0x33/0xf0 [mac80211]
ieee80211_stop_device+0x43/0x50 [mac80211]
ieee80211_do_stop+0x4f2/0x810 [mac80211]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196043
Reported-by: Giulio Genovese <giulio.genovese@gmail.com>
Tested-by: Giulio Genovese <giulio.genovese@gmail.com>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bde717ab473668377fc65872398a102d40cb2d58 upstream.
The hard coded register 0x9864 and 0x9924 are invalid
for ar9300 chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf8ce1ea61b75712a154c93e40f2a5af2e4dd997 upstream.
One scenario that could lead to UAF is two threads writing
simultaneously to the "tx99" debug file. One of them would
set the "start" value to true and follow to ath9k_tx99_init().
Inside the function it would set the sc->tx99_state to true
after allocating sc->tx99skb. Then, the other thread would
execute write_file_tx99() and call ath9k_tx99_deinit().
sc->tx99_state would be freed. After that, the first thread
would continue inside ath9k_tx99_init() and call
r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl);
that would make use of the freed sc->tx99_skb memory.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b08b5b53a1ed2bd7a883f8fd29232c8f03604671 upstream.
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b3389a ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1427228d5869f5804b03d47acfa4a88122572a78 upstream.
This fixes the below crash when ath10k probe firmware fails, NAPI polling tries
to access a rx ring resource which was never allocated. An easy way to
reproduce this is easy to remove all the firmware files, load ath10k modules
and ath10k will crash when calling 'rmmod ath10k_pci'. The fix is to call
napi_enable() from ath10k_pci_hif_start() so that it matches with
napi_disable() being called from ath10k_pci_hif_stop().
Big thanks to Mohammed Shafi Shajakhan who debugged this and provided first
version of the fix. In this patch I just fix the actual problem in pci.c
instead of having a workaround in core.c.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
__ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
Call Trace:
[<ffffffffa113ec62>] ath10k_htt_rx_msdu_buff_replenish+0x42/0x90
[ath10k_core]
[<ffffffffa113f393>] ath10k_htt_txrx_compl_task+0x433/0x17d0
[ath10k_core]
[<ffffffff8114406d>] ? __wake_up_common+0x4d/0x80
[<ffffffff811349ec>] ? cpu_load_update+0xdc/0x150
[<ffffffffa119301d>] ? ath10k_pci_read32+0xd/0x10 [ath10k_pci]
[<ffffffffa1195b17>] ath10k_pci_napi_poll+0x47/0x110 [ath10k_pci]
[<ffffffff817863af>] net_rx_action+0x20f/0x370
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 3c97f5de1f28 ("ath10k: implement NAPI support")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebeb36670ecac36c179b5fb5d5c88ff03ba191ec upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16ff1fb0e32f76a5d285a6f23b82d21aa52813c6 upstream.
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=1eda ProdID=2315 Rev=01.08
S: Manufacturer=ATHEROS
S: Product=USB2.0 WLAN
S: SerialNumber=12345
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 6 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40bea976c72b9ee60f8d097852deb53ccbeaffbe upstream.
relay_open() may return NULL, check the return value to avoid the crash.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
IP: [<ffffffffa01a95c5>] ath_cmn_process_fft+0xd5/0x700 [ath9k_common]
PGD 41cf28067 PUD 41be92067 PMD 0
Oops: 0000 [#1] SMP
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.6+ #35
Hardware name: Hewlett-Packard h8-1080t/2A86, BIOS 6.15 07/04/2011
task: ffffffff81e0c4c0 task.stack: ffffffff81e00000
RIP: 0010:[<ffffffffa01a95c5>] [<ffffffffa01a95c5>] ath_cmn_process_fft+0xd5/0x700 [ath9k_common]
RSP: 0018:ffff88041f203ca0 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 000000000000059f RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000040 RDI: ffffffff81f0ca98
RBP: ffff88041f203dc8 R08: ffffffffffffffff R09: 00000000000000ff
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffffffff81f0ca98 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88041f200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000040 CR3: 000000041b6ec000 CR4: 00000000000006f0
Stack:
0000000000000363 00000000000003f3 00000000000003f3 00000000000001f9
000000000000049a 0000000001252c04 ffff88041f203e44 ffff880417b4bfd0
0000000000000008 ffff88041785b9c0 0000000000000002 ffff88041613dc60
Call Trace:
<IRQ>
[<ffffffffa01b6441>] ath9k_tasklet+0x1b1/0x220 [ath9k]
[<ffffffff8105d8dd>] tasklet_action+0x4d/0xf0
[<ffffffff8105dde2>] __do_softirq+0x92/0x2a0
Reported-by: Devin Tuchsen <devin.tuchsen@gmail.com>
Tested-by: Devin Tuchsen <devin.tuchsen@gmail.com>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9f1e32600816d695f817477d56490bfc2ba43c6 upstream.
This patch fixes the OTP register definitions for the AR934x and AR9550
WMAC SoC.
Previously, the ath9k driver was unable to initialize the integrated
WMAC on an Aerohive AP121:
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: Unable to initialize hardware; initialization status: -5
| ath9k ar934x_wmac: failed to initialize device
| ath9k: probe of ar934x_wmac failed with error -5
It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA
definitions contain a typo.
Cc: Gabor Juhos <juhosg@openwrt.org>
Fixes: add295a4afbdf5852d0 "ath9k: use correct OTP register offsets for AR9550"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a5e969bb2f6692a256352649355d56d018d6b88 upstream.
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a70e1d6fd6b5e1a81fa6171600942bee34f5128f upstream.
Simply return -EOPNOTSUPP instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb4281528b62207918b1e95827cad7527aa4dbaa upstream.
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31b239824ece321c09bdb8e61e1d14814eaba38b upstream.
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220d2 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fcf7cf1551cae54e747a771f5808240f2a37708f upstream.
This partially reverts 'commit 2cdce425aa33
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa33 "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1f1c0e289e1bc46cd6873ba6dd6c627f459e7fa upstream.
Starting with commit d94a461d7a7d ("ath9k: use ieee80211_tx_status_noskb
where possible") the driver uses rcu_read_lock() && rcu_read_unlock(), yet on
returning early in ath_tx_edma_tasklet() the unlock is missing leading to stalls
and suspicious RCU usage:
===============================
[ INFO: suspicious RCU usage. ]
4.9.0-rc8 #11 Not tainted
-------------------------------
kernel/rcu/tree.c:705 Illegal idle entry in RCU read-side critical section.!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/7/0:
#0:
(
rcu_read_lock
){......}
, at:
[<ffffffffa06ed110>] ath_tx_edma_tasklet+0x0/0x450 [ath9k]
stack backtrace:
CPU: 7 PID: 0 Comm: swapper/7 Not tainted 4.9.0-rc8 #11
Hardware name: Acer Aspire V3-571G/VA50_HC_CR, BIOS V2.21 12/16/2013
ffff88025efc3f38 ffffffff8132b1e5 ffff88017ede4540 0000000000000001
ffff88025efc3f68 ffffffff810a25f7 ffff88025efcee60 ffff88017edebdd8
ffff88025eeb5400 0000000000000091 ffff88025efc3f88 ffffffff810c3cd4
Call Trace:
<IRQ>
[<ffffffff8132b1e5>] dump_stack+0x68/0x93
[<ffffffff810a25f7>] lockdep_rcu_suspicious+0xd7/0x110
[<ffffffff810c3cd4>] rcu_eqs_enter_common.constprop.85+0x154/0x200
[<ffffffff810c5a54>] rcu_irq_exit+0x44/0xa0
[<ffffffff81058631>] irq_exit+0x61/0xd0
[<ffffffff81018d25>] do_IRQ+0x65/0x110
[<ffffffff81672189>] common_interrupt+0x89/0x89
<EOI>
[<ffffffff814ffe11>] ? cpuidle_enter_state+0x151/0x200
[<ffffffff814ffee2>] cpuidle_enter+0x12/0x20
[<ffffffff8109a6ae>] call_cpuidle+0x1e/0x40
[<ffffffff8109a8f6>] cpu_startup_entry+0x146/0x220
[<ffffffff810336f8>] start_secondary+0x148/0x170
Signed-off-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Fixes: d94a461d7a7d ("ath9k: use ieee80211_tx_status_noskb where possible")
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79e57dd113d307a6c74773b8aaecf5442068988a upstream.
The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit
0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.
I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.
This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.
With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.
While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.
Fixes: 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.")
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91851cc7a939039bd401adb6ca3da4402bec1d0c upstream.
Commit b2d70d4944c1 ("ath9k: make GPIO API to support both of WMAC and
SOC") refactored ath9k_hw_gpio_get() to support both WMAC and SOC GPIOs,
changing the return on success from 1 to BIT(gpio). This broke some callers
like ath_is_rfkill_set(). This doesn't fix any known bug in mainline at the
moment, but should be fixed anyway.
Instead of fixing all callers, change ath9k_hw_gpio_get() back to only
return 0 or 1.
Fixes: b2d70d4944c1 ("ath9k: make GPIO API to support both of WMAC and SOC")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
[kvalo@qca.qualcomm.com: mention that doesn't fix any known bug]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2cac2f74ab4bcf0db0dcf3a612f1e5b52d145c8 upstream.
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f28 ("ath10k: implement NAPI support")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
wlcore
* fix a double free regression causing hard to track crashes
rtl8xxxu
* fix driver reload issues, a memory leak and an endian bug
rtlwifi
* fix a major regression introduced in 4.9 with firmware loading on
certain hardware
ath10k
* fix regression about broken cal_data debugfs file (since 4.7)
ath9k
* revert temperature compensation for AR9003+ devices, it was causing
too much problems
ath6kl
* add Dell OEM SDIO I/O for the Venue 8 Pro
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SDIO ID 0271:0418
Signed-off-by: Alan Cox <alan@linux.intel.com>
Bugzilla-ID: https://bugzilla.kernel.org/show_bug.cgi?id=67921
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This reverts commit 171f6402e4aa ("ath9k_hw: implement temperature compensation
support for AR9003+"). Some users report that this commit causes a regression
in performance under some conditions.
Fixes: 171f6402e4aa ("ath9k_hw: implement temperature compensation support for AR9003+")
Cc: <stable@vger.kernel.org> # 4.8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Commit 0b8e3c4ca29f ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:
static ssize_t ath10k_debug_cal_data_read(struct file *file,
char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
void *buf = file->private_data;
This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).
The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.
Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4ca29f ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that
happened in 4.8 for that filesystem. Overall, nothing major, just a
few fixes and cleanups.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent()
drivers: dma-coherent: Fix DMA coherent size for less than page
MAINTAINERS: extend firmware_class maintainer list
debugfs: propagate release() call result
driver-core: platform: Catch errors from calls to irq_get_irq_data
sysfs print name of undiscoverable attribute group
carl9170: fix debugfs crashes
b43legacy: fix debugfs crash
b43: fix debugfs crash
debugfs: introduce a public file_operations accessor
device core: Remove deprecated create_singlethread_workqueue
drivers/base dmam_declare_coherent_memory leaks
platform: don't return 0 from platform_get_irq[_byname]() on error
cpu: clean up register_cpu func
dma-mapping: use vma_pages().
drivers: dma-coherent: use vma_pages().
attribute_container: Fix typo
base: soc: make it explicitly non-modular
drivers: base: dma-mapping: page align the size when unmap_kernel_range
platform driver: fix use-after-free in platform_device_del()
...
|
|
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath9k RNG will dominates all the noise sources from the real HW
RNG, disable it by default. But we strongly recommand to enable
it if the system without HW RNG, especially on embedded systems.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Use the managed variant of reset_control_get() to simplify the
failure path and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Use the managed variant of clk_get() to simplify the failure path
and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Ben Greear reported:
> I see lots of instability as soon as I load up the carl9710 NIC.
> My application is going to be poking at it's debugfs files...
>
> BUG: KASAN: slab-out-of-bounds in carl9170_debugfs_read+0xd5/0x2a0
> [carl9170] at addr 0xffff8801bc1208b0
> Read of size 8 by task btserver/5888
> =======================================================================
> BUG kmalloc-256 (Tainted: G W ): kasan: bad access detected
> -----------------------------------------------------------------------
>
> INFO: Allocated in seq_open+0x50/0x100 age=2690 cpu=2 pid=772
>...
This breakage was caused by the introduction of intermediate
fops in debugfs by commit 9fd4dcece43a
("debugfs: prevent access to possibly dead file_operations at file open")
Thankfully, the original/real fops are still available in d_fsdata.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for 4.9. Major changes:
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
|
|
hw_4addr_pad was added to handle different types of padding
in 4-address rx frame. But this padding is not very specific
to 4-address, it can happen even with three address + ethernet
decap mode. Since the padding information can be obtained
through Rx desc for QCA99X0 and newer chips, this hw_param
is not needed any more.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In QCA99X0 (QCA99X0, QCA9984, QCA9888 and QCA4019) family chips,
hw adds padding at the begining of the rx payload to make L3
header 4-byte aligned. In the chips doing this type of padding,
the number of bytes padded will be indicated through msdu_end:info1.
Define a hw_rx_desc_ops wrapper to retrieve the number of padded
bytes and use this while doing undecap. This should fix padding
related issues with ethernt decap format with QCA99X0, QCA9984,
QCA9888 and QCA4019 hw.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There are slight differences in Rx hw descriptor information
among different chips. So far driver does not use those new
information for any functionalities, but there is one important
information which is available from QCA99X0 onwards to indicate
the number of bytes that hw padded at the begining of the rx
payload and this information is needed to undecap the rx
packet. Add an abstraction for Rx desc to make use of the
new desc information available. The callback that this patch
defines to retrieve the padding bytes will be used in follow-up
patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|