Age | Commit message (Collapse) | Author |
|
Add a new .bus_name to virtio_config_ops then modify virtio_net to
call through to it in an ethtool .get_drvinfo routine to report
bus_info in ethtool -i output which is consistent with other
emulated NICs and the output of lspci.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds phy reset functionality to mdio-gpio driver. Now
mdio_gpio_platform_data has new member as function pointer which can be
filled at the bsp level for a callback from phy infrastructure. Also the
mdio-bitbang driver fills-in the reset function of mii_bus structure.
Without this patch the bsp level code has to takecare of the reseting
PHY's on the bus, which become bit hacky for every bsp and
phy-infrastructure is ignored aswell.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue introduced recently with commit
452448f9283e1939408b397e87974a418825b0a8.
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy. It also does a modicum of other
cleaning in those routines.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x uses following formula to compute its rx_buf_sz :
dev->mtu + 2*L1_CACHE_BYTES + 14 + 8 + 8 + 2
Then core network adds NET_SKB_PAD and SKB_DATA_ALIGN(sizeof(struct
skb_shared_info))
Final allocated size for skb head on x86_64 (L1_CACHE_BYTES = 64,
MTU=1500) : 2112 bytes : SLUB/SLAB round this to 4096 bytes.
Since skb truesize is then bigger than SK_MEM_QUANTUM, we have lot of
false sharing because of mem_reclaim in UDP stack.
One possible way to half truesize is to reduce the need by 64 bytes
(2112 -> 2048 bytes)
Instead of allocating a full cache line at the end of packet for
alignment, we can use the fact that skb_shared_info sits at the end of
skb->head, and we can use this room, if we convert bnx2x to new
build_skb() infrastructure.
skb_shared_info will be initialized after hardware finished its
transfert, so we can eventually overwrite the final padding.
Using build_skb() also reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are recycled while still hot.
Performance results :
(820.000 pps on a rx UDP monothread benchmark, instead of 720.000 pps)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Tom Herbert <therbert@google.com>
CC: Jamal Hadi Salim <hadi@mojatatu.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Thomas Graf <tgraf@infradead.org>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 952c5ca1 (fsl_pq_mdio: Clean up tbi address configuration) .probe returns
-EBUSY when the "tbi-phy" node is missing. Fix this.
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds listen only mode to the mscan controller.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support enabling/disabling/querying internal loopback mode for
forcedeth NICs using ethtool.
Signed-off-by: Sanjay Hortikar <horti@google.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces new network device called team. It supposes to be
very fast, simple, userspace-driven alternative to existing bonding
driver.
Userspace library called libteam with couple of demo apps is available
here:
https://github.com/jpirko/libteam
Note it's still in its dipers atm.
team<->libteam use generic netlink for communication. That and rtnl
suppose to be the only way to configure team device, no sysfs etc.
Python binding of libteam was recently introduced.
Daemon providing arpmon/miimon active-backup functionality will be
introduced shortly. All what's necessary is already implemented in
kernel team driver.
v7->v8:
- check ndo_ndo_vlan_rx_[add/kill]_vid functions before calling
them.
- use dev_kfree_skb_any() instead of dev_kfree_skb()
v6->v7:
- transmit and receive functions are not checked in hot paths.
That also resolves memory leak on transmit when no port is
present
v5->v6:
- changed couple of _rcu calls to non _rcu ones in non-readers
v4->v5:
- team_change_mtu() uses team->lock while travesing though port
list
- mac address changes are moved completely to jurisdiction of
userspace daemon. This way the daemon can do FOM1, FOM2 and
possibly other weird things with mac addresses.
Only round-robin mode sets up all ports to bond's address then
enslaved.
- Extended Kconfig text
v3->v4:
- remove redundant synchronize_rcu from __team_change_mode()
- revert "set and clear of mode_ops happens per pointer, not per
byte"
- extend comment of function __team_change_mode()
v2->v3:
- team_change_mtu() uses rcu version of list traversal to unwind
- set and clear of mode_ops happens per pointer, not per byte
- port hashlist changed to be embedded into team structure
- error branch in team_port_enter() does cleanup now
- fixed rtln->rtnl
v1->v2:
- modes are made as modules. Makes team more modular and
extendable.
- several commenters' nitpicks found on v1 were fixed
- several other bugs were fixed.
- note I ignored Eric's comment about roundrobin port selector
as Eric's way may be easily implemented as another mode (mode
"random") in future.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The race may cause access of registers while MAC hw block is
in reset state. As a result syslog will show error messages.
We can prevent this by using state from local variable.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shut down the device in case of fan failure to prevent HW damage.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need propagate the DCBX results from PMF to other functions
on the same port, in order to properly update netdev structure
and allow following new ETS and PFC configurations.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FCoE license info must be initialized at probe(), but
iSCSI at open().
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A FW cmd timeout (with a sufficiently large timeout value in the
order of tens of seconds) indicates an unresponsive FW. In this state
issuing further cmds and waiting for a completion will only stall the process.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we're spamming error messages each time a FW cmd call is made
while in EEH/UE error state. One log msg on error detection is enough.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize if_handle, vf_if_handle and vf_pmac_id with "-1" so that in
failure cases when be_clear() is called, we can skip over
if_destroy/pmac_del cmds if they have not been created.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables the ioctl support for the driver. So userspace
programs like mii-tool can work.
Resend in merge window
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tunnels can force an alignment of their percpu data to reduce number of
cache lines used in fast path, or read in .ndo_get_stats()
percpu_alloc() is a very fine grained allocator, so any small hole will
be used anyway.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To prevent the SBus driver for Sun Happy Meal cards from being loaded for
PCI cards utilizing the same chipset, a filter was added to the probe
function in commit 0b492fce3d72d982a7981905f85484a1e1ba7fde.
The filter was implemented by checking the name of the parent node in
the OF tree. This patch extends this filter, so that the driver will
load on SBus systems that are based upon SBI SBus Bridges.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver used NET_IP_ALIGN to remove some additional padding inside of
the rx_fixup function. On many architectures NET_IP_ALIGN defaults to 2
which removed the correct amount of bytes.
On MCORE2-machines commit ea812ca1b06113597adcd8e70c0f84a413d97544
introduces a change which sets NET_IP_ALIGN to 0 by default. Which
triggered the bug on these machines.
This fix introduces a new RXW_PADDING define and uses this instead of
NET_IP_ALIGN. The name was taken from the original SMSC7500 driver which
is provided by SMSC.
Signed-off-by: Nico Erfurth <ne@erfurth.eu>
Tested-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
|
|
This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx byte count was off; instead use the hardware's count. Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.
- The count of transmitted packets reported by the forcedeth driver
reports pre-TSO (TCP Segmentation Offload) packet counts and not the
count of the number of packets sent on the wire. This change fixes
the forcedeth driver to report the correct count. Fixed the code by
copying the count stored in the NIC H/W to the value reported by the
driver.
- Count rx_drop_frame errors as rx_fifo_errors:
We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
for too long. Normally, rx_fifo_errors would be counted in this case.
The rx_drop_frame error count is private to forcedeth and is not
reported by ifconfig or sysfs. The rx_fifo_errors count is currently
unused in the forcedeth driver. It is reported by ifconfig as overruns.
This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.
Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process. This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().
Tested:
x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
+ rmmod/modprobe/ifconfig in a loop
Initial-Author: Salman Qazi <sqazi@google.com>
Discussion: http://patchwork.ozlabs.org/patch/123548/
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the bug added in commit v3.1-rc7-1055-gf9b491e
SKB can be NULL at this point, at least for cdc-ncm.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix compiler errors and warnings with CONFIG_PCI_IOV defined and not
defined.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scsi: drop unused Kconfig symbol
pci: drop unused Kconfig symbol
stmmac: drop unused Kconfig symbol
x86: drop unused Kconfig symbol
powerpc: drop unused Kconfig symbols
powerpc: 40x: drop unused Kconfig symbol
mips: drop unused Kconfig symbols
openrisc: drop unused Kconfig symbols
arm: at91: drop unused Kconfig symbol
samples: drop unused Kconfig symbol
m32r: drop unused Kconfig symbol
score: drop unused Kconfig symbols
sh: drop unused Kconfig symbol
um: drop unused Kconfig symbol
sparc: drop unused Kconfig symbol
alpha: drop unused Kconfig symbol
Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/vmalloc-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
net: xen-netback: use API provided by xenbus module to map rings
block: xen-blkback: use API provided by xenbus module to map rings
xen: use generic functions instead of xen_{alloc, free}_vm_area()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
|
|
slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.
The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: Pavel Mateja <pavel@netsafe.cz>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When implementing VRRP v2 using macvlan several problems were
discovered. VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work. The problem is that packets with a macvlan device's
source address are not received.
The problem is actually a regression that date back almost 2 years now.
The original problems started with:
commit 618e1b7482f7a8a4c6c6e8ccbe140e4c331df4e9
Author: Arnd Bergmann <arnd@arndb.de>
Date: Thu Nov 26 06:07:10 2009 +0000
macvlan: implement bridge, VEPA and private mode
This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|